Surfacing Technology for the Inner Wall of a Pressurised Coal Gasifier
Why This Paper Matters to Anyone Who Has Ever Owned a Gasifier
I have spent more than thirty years in this business, and I have signed off on gasifiers, heat exchangers and pressure vessels that had to survive hydrogen, sulphides and high-temperature creep. The pressurised coal gasifier is one of the most punishing pieces of equipment we build. The inner wall does not just see process gas; it sees ash, slag, chlorides, sulphides and thermal cycling that would eat a carbon steel wall in months. This paper by Ma Xiaobing and his colleagues at Xinjiang Lanshi Heavy Energy Engineering is a practical look at how we choose a surfacing alloy and a surfacing process for that duty. It is not a laboratory curiosity; it is a production-floor decision.
The Corrosion Mechanism Is the Starting Point
The authors correctly identify that the inner wall of a pressurised gasifier fails by a combination of high-temperature oxidation, sulphidation and, in many cases, metal dusting. The gasifier atmosphere is reducing, with high partial pressures of CO and H2, and the presence of sulphur compounds drives sulphidation attack. The temperature range is typically 900 to 1400 degrees C, and the slag layer that forms on the wall is both chemically aggressive and mechanically abrasive.
| Corrosion Mode | Typical Temperature Range | Dominant Species | Practical Consequence |
|---|---|---|---|
| High-temperature oxidation | 800-1200 C | O2, CO2, H2O | Oxide scale spallation, wall thinning |
| Sulphidation | 600-1000 C | H2S, SO2, organic S | Rapid metal loss, pitting |
| Metal dusting | 400-800 C | CO, H2, carburising gas | Localised pitting, catastrophic metal loss |
| Slag erosion | 1000-1400 C | Molten ash, FeS, CaS | Abrasive wear, thermal shock cracking |
The key insight is that no single mechanism dominates in all zones. The upper wall may see more metal dusting, while the lower slag zone sees erosion and sulphidation. The surfacing alloy must therefore be selected for the worst-case combination, not for a single mechanism.
Surfacing Alloy Selection: What the Paper Really Tells Us
The paper compares a range of surfacing materials, from austenitic stainless steels to nickel-based alloys. The authors do not simply say "use Inconel 625"; they compare the corrosion resistance, the weldability and the cost. In my experience, the selection matrix is always a compromise between corrosion performance, dilution control and the ability to deposit a sound layer without cracking.
| Alloy Family | Typical Composition | Corrosion Resistance | Weldability | Relative Cost | Typical Use |
|---|---|---|---|---|---|
| 309L / 312L | Fe-Cr-Ni | Moderate | Excellent | Low | Transition layer only |
| 625 (Ni-Cr-Mo) | Ni-22Cr-9Mo-3.5Nb | High | Good | High | Full surfacing, high sulphur |
| C-276 (Ni-Cr-Mo) | Ni-16Cr-16Mo-4W | Very high | Moderate | Very high | Severe sulphidation |
| 59 (Ni-Cr-Mo) | Ni-23Cr-16Mo | Very high | Moderate | Very high | Severe sulphidation + erosion |
| 22 (Ni-Cr-Mo) | Ni-22Cr-13Mo-3W | High | Good | High | General service |
The paper's contribution is to highlight that the choice is not simply "nickel is better than stainless". The dilution from the carbon steel base metal is the enemy. If you deposit a 625 layer with 30 percent dilution, the effective nickel content drops and the corrosion resistance falls off a cliff. The authors emphasise that a two-layer deposit, or a buffer layer of 309L followed by a 625 cap, is often the only way to guarantee the specified chemistry at the surface.
Surfacing Process Selection: Where the Real Engineering Lives
The paper compares several surfacing processes, and this is where I want to focus my own comments. The process choice determines dilution, deposition rate, heat input and residual stress. In a production shop, the decision is rarely made on metallurgy alone; it is made on throughput, defect rate and the ability to repair.
| Process | Typical Dilution | Deposition Rate | Heat Input | Defect Risk | Best For |
|---|---|---|---|---|---|
| GTAW (TIG) | 5-10% | Low | Low | Low | Small areas, repairs, precision |
| GMAW (MIG) | 15-25% | Medium | Medium | Medium | General surfacing |
| FCAW | 15-25% | Medium | Medium | Medium | General surfacing, site work |
| SAW (strip or wire) | 10-20% | High | High | Low | Large flat surfaces, production |
| PTA (plasma transferred arc) | 5-10% | Medium | Low | Low | Precision, low dilution |
| Laser cladding | 2-5% | Medium | Very low | Low | High-end, thin sections |
The paper correctly notes that for a gasifier inner wall, the two dominant production routes are submerged arc strip cladding and plasma transferred arc surfacing. Strip cladding gives high deposition rates and low dilution, but it requires a flat or gently curved surface. PTA gives excellent control and low dilution, but it is slower and more sensitive to parameter drift. In my own experience, I have seen both routes used successfully, and I have also seen both fail when the parameters were not controlled.
Practical Lessons from the Shop Floor
I want to add a few observations that the paper touches on but does not fully develop, because they are the ones that cause real problems on the shop floor.
- Preheat and interpass temperature are not optional. A gasifier shell is typically 50 to 120 mm thick carbon steel. If you deposit a nickel-based layer on that without preheat, you get hydrogen cracking in the HAZ and, worse, you get delayed cracking that shows up days later during hydrotest. I have seen a 60 mm thick shell crack through the base metal because the welder ignored the preheat requirement. The paper mentions preheat, but the production floor must treat it as a hold point, not a suggestion.
- Dilution control is a quality control issue, not just a metallurgical one. The standard approach is to measure the iron content of the first layer. If it exceeds the specified limit (typically 10 percent for 625), you have two choices: deposit a second layer, or scrap the part. The paper's emphasis on single-layer versus multi-layer is well placed. In my experience, the cheapest way to guarantee chemistry is to use a buffer layer of 309L, then deposit the nickel layer on top. The buffer layer absorbs the dilution, and the nickel layer stays clean.
- Weld repair is a fact of life. Even with the best process control, you will get slag inclusions, lack of fusion and porosity. The paper does not discuss repair in detail, but the production engineer must plan for it. A repair on a nickel-based surfacing is not the same as a repair on carbon steel. You need a qualified repair procedure, a dedicated repair welder and a documented repair history. I have seen vessels rejected because the repair was done with the wrong filler and the chemistry at the repair site failed.
- NDT is the final gate. The paper mentions that the surfacing layer must be examined, but it does not specify the method. In practice, you will use UT for bond integrity, PT for surface defects and, in some cases, PAUT for volumetric examination. The acceptance criteria are typically based on API 5L, ASME Section VIII or a project-specific specification. The key point is that the NDT must be performed after any post-weld heat treatment, because PWHT can open up defects that were not visible before.
Standards and Specifications: What the Paper Leaves Out
The paper references Chinese standards, but it does not discuss the international framework. For a gasifier that is exported, the relevant standards are ASME Section VIII Div 1 or Div 2, and the surfacing requirements are typically specified in the purchase order. The key clauses are:
| Standard / Clause | Requirement | Practical Impact |
|---|---|---|
| ASME VIII Div 1, UW-27 | Welding procedure qualification | Surfacing must be qualified separately |
| ASME IX, QW-482 | WPS/PQR for surfacing | Must specify alloy, thickness range, position |
| API 5L, Annex H | Chemical composition limits | Iron content of first layer typically 10% max |
| Project spec | Hardness limit | Typically 22 HRC max for 625 |
| Project spec | Ferrite content | Typically 3-8 FN for austenitic stainless |
The paper's contribution is to show that the choice of surfacing alloy and process is not a simple "pick the most corrosion-resistant" decision. It is a systems engineering problem that involves the base metal, the welding process, the NDT requirements and the final service environment.
My Own Reflection and a Word of Caution
I have read this paper with interest because it addresses a real problem that I have seen on the shop floor and on site. The authors have done a competent job of comparing materials and processes, and their conclusion that a two-layer deposit is often necessary is correct. However, I would add one caution that is not in the paper: the corrosion resistance of a surfacing layer is only as good as its weakest point. A single lack of fusion, a single slag inclusion or a single crack at the bond line can become a corrosion cell that eats through the layer in months. The quality of the deposit, not just its chemistry, determines the service life.
I would also caution against the temptation to specify a more expensive alloy than necessary. I have seen projects where the client specified C-276 for a service that 625 would have handled, and the cost difference was significant. The paper's comparison table is useful, but the final decision must be based on the actual process conditions, not on a generic "nickel is better" assumption.
Key Takeaways for the Practising Engineer
- The corrosion mechanism is a combination of oxidation, sulphidation and metal dusting. The surfacing alloy must be selected for the worst-case combination.
- Dilution is the enemy. A buffer layer of 309L followed by a 625 cap is the most reliable route to guaranteed chemistry.
- Process selection is a production decision. Strip cladding for large flat surfaces, PTA for precision and low dilution.
- Preheat and interpass temperature are hold points, not suggestions. Ignoring them leads to cracking.
- NDT is the final gate. UT, PT and PAUT are all required, and they must be performed after PWHT.
- Repair is a fact of life. Plan for it, qualify it and document it.
Conclusion
This paper is a solid contribution to the practical literature on gasifier inner wall surfacing. It does not break new ground in metallurgy, but it provides a clear framework for the production engineer who has to make a decision on the shop floor. The key message is that the choice of surfacing alloy and process is a systems engineering problem, not a materials selection exercise. If you take one thing away from this paper, it is this: the corrosion resistance of a surfacing layer is only as good as its weakest point, and the weakest point is usually a welding defect. Control the process, control the dilution, control the NDT, and you will have a gasifier that lasts.
Zhuojin Pipe Fitting Co., Ltd