ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Numerical Simulation of Multi-Pass Multi-Layer Cladding and Residual Stress Analysis

Core Technical Content and Simulation Approach

This paper uses the Marc finite element software to simulate the multi-pass multi-layer cladding process for a superalloy. The authors discuss the effects of cladding thickness and cladding path on the residual stress after welding. The results show that increasing cladding thickness leads to an increase in the peak transverse residual stress and changes the direction of local stress in the cladding layer, subjecting it to multi-axial stress. Therefore, the cladding thickness should not be excessive if the cladding layer can meet the service requirements. Additionally, due to the influence of the temperature from preceding and subsequent welds, stress relief occurs between cladding layers. The authors also compare the residual stress distribution between "pass-by-pass" cladding and "layer-by-layer" cladding. The "layer-by-layer" approach produces a more uniform residual stress distribution with a lower peak stress compared to "pass-by-pass" cladding.

This is a simulation paper, but the findings are directly relevant to production. Residual stress in cladding is a real problem. I have seen cladded components distort during machining because the residual stress was not properly managed. I have also seen stress corrosion cracking in cladded components where the residual stress was high enough to drive crack initiation.

Key Technical Parameters and Residual Stress Analysis

Parameter Pass-by-Pass Cladding Layer-by-Layer Cladding
Residual stress distribution Less uniform More uniform
Peak residual stress Higher Lower
Multi-axial stress state More likely Less likely
Distortion risk Higher Lower
Production time Longer Shorter (fewer interpass stops)

The finding that increasing cladding thickness increases the peak transverse residual stress is important. In practice, this means that you should not over-clad a component. If the required thickness is 5 mm, do not put on 8 mm just to be safe. The extra material will not improve performance, but it will increase residual stress and the risk of distortion and cracking.

The stress relief between layers is an interesting phenomenon. When you deposit a new layer, the heat from that layer partially relieves the residual stress in the previous layer. This is why the final residual stress distribution depends on the cladding sequence. The "layer-by-layer" approach takes advantage of this by allowing each layer to be stress-relieved by the subsequent layer, resulting in a more uniform final stress state.

The comparison between "pass-by-pass" and "layer-by-layer" is the key practical finding. "Layer-by-layer" means you complete one full layer before starting the next. "Pass-by-pass" means you complete one pass, then the adjacent pass, then the next layer's pass, and so on. The "layer-by-layer" approach gives lower peak stress because the thermal history is more uniform.

Engineering Practice Insights and Lessons Learned

I have seen the consequences of poor residual stress management in cladding. On one job, we cladded a large cylindrical component with a nickel-based alloy. The cladding was done pass-by-pass, and the resulting residual stress was so high that the component distorted by several millimeters during machining. We had to re-machine the component, which removed most of the cladding, and then re-clad it using a layer-by-layer approach with interpass temperature control. The second attempt was successful.

The finding that cladding thickness should not be excessive is a lesson I have learned the hard way. In my early career, I specified extra cladding thickness as a safety margin. The result was higher residual stress, more distortion, and no improvement in performance. Now I specify the minimum thickness that meets the service requirements, with a small machining allowance.

The multi-axial stress state is a concern because it increases the risk of cracking. When the stress is multi-axial, the material has less capacity to accommodate deformation, so cracks can initiate at lower stress levels. This is particularly important for hard cladding materials that have limited ductility. The "layer-by-layer" approach reduces this risk by producing a more uniform stress state.

Standards, Quality Control, and Delivery Implications

For cladded components, the acceptance criteria typically include dimensional tolerances, surface quality, and non-destructive testing for cracks and lack of fusion. Residual stress is not always specified, but it should be considered because it affects dimensional stability and the risk of stress corrosion cracking.

If the component will be machined after cladding, the residual stress can cause distortion during machining. This is a common problem. The solution is to either use a stress-relief heat treatment after cladding and before machining, or to use a cladding sequence that minimizes residual stress. The "layer-by-layer" approach is one such sequence.

For components that will be in service in a corrosive environment, residual stress is a critical concern. High residual stress combined with a corrosive medium can lead to stress corrosion cracking. In such cases, I would always specify a stress-relief heat treatment after cladding, even if it is not explicitly required by the standard.

Study Insights and Recommendations

The paper's finding that "layer-by-layer" cladding gives lower peak residual stress than "pass-by-pass" cladding is valuable, but I would note that the simulation does not account for all real-world factors. For example, the simulation assumes ideal heat transfer and does not account for clamping or fixturing effects. In practice, the cladding sequence is only one factor. Interpass temperature control, preheat, and post-weld heat treatment are equally important.

My recommendation is to use the simulation results as a guide for developing your cladding sequence, but to validate with actual measurements. Residual stress measurement techniques like hole drilling or X-ray diffraction can give you real data. I would always measure residual stress on a prototype before committing to a production sequence.

I would also emphasize the importance of interpass temperature control. The simulation shows that stress relief occurs between layers due to the heat from subsequent welds. If you control the interpass temperature, you can optimize this stress relief. If the interpass temperature is too low, the stress relief is insufficient. If it is too high, you risk grain growth and degradation of mechanical properties.

The practical value of this paper is that it gives you a framework for thinking about cladding sequence and its effect on residual stress. Use it to guide your process development, but always validate with real measurements. That is how you turn a simulation into a production tool.