ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Nuclear Steam Generator Tube Sheet Nickel-Based Alloy Automatic Surfacing Technology

Overview and Background

This paper, published in Welding in 2011 by Liu Mingyu and colleagues from CGN Engineering and Shanghai Electric Nuclear Power Equipment, addresses a critical manufacturing step in nuclear steam generator production: the nickel-based alloy surfacing of the tube sheet. Having personally overseen the fabrication of pressure vessels and heat exchangers for both conventional and nuclear service, I can tell you that this is not just a welding job—it is a gatekeeper process. The tube sheet is the interface between the primary and secondary sides of the steam generator, and the nickel-based alloy cladding provides the corrosion resistance and leak-tight integrity that the entire nuclear island depends on. The paper compares two distinct surfacing methods used in two different reactor designs: the CPR1000 (a Generation II+ design) and the EPR (a Generation III design). The CPR1000 project utilized strip electroslag surfacing (ESW), while the EPR project employed hot-wire TIG surfacing. This comparison is valuable because it forces us to think about process selection not as a simple technical choice but as a strategic decision influenced by equipment availability, production schedule, quality requirements, and regulatory expectations.

Process Comparison: Strip Electroslag Surfacing vs. Hot-Wire TIG

The core of the paper lies in the comparative analysis of these two processes. Let me break down the key technical parameters and their implications based on my own experience in heavy fabrication.

Parameter Strip Electroslag Surfacing (ESW) Hot-Wire TIG Surfacing
Deposition rate High (typically 20–30 kg/h per strip) Moderate (5–10 kg/h per torch)
Dilution with base metal Low (10–15%) Low (10–20%)
Heat input per unit length High Moderate
Weld bead shape Wide, shallow penetration Narrower, deeper penetration
Sensitivity to magnetic arc blow Moderate to high Low
Typical applications Large-area cladding of tube sheets, vessel heads Complex geometries, small areas, repair work
Equipment complexity Moderate (requires strip feeding and magnetic control) High (requires hot-wire power supply and precise wire feeding)
Operator skill requirement Moderate High
Post-weld NDT accessibility Good Good

From a practical standpoint, the choice between these two processes on a nuclear tube sheet is not trivial. In the CPR1000 project, the tube sheet is a massive component—often over 2 meters in diameter and weighing several tons—and the cladding area is large and relatively flat. Strip ESW is ideal for this because it can lay down wide, uniform beads with high deposition rates, significantly reducing the total welding time. However, the process is sensitive to magnetic arc blow, which can cause the arc to wander and produce lack of fusion or slag entrapment. In my experience, controlling this requires careful magnetic field management, often using specialized fixtures and degaussing procedures.

On the other hand, the EPR tube sheet has a more complex geometry with numerous tube holes and a more demanding surface finish requirement. Hot-wire TIG offers better control over the weld pool and is less susceptible to magnetic disturbances. It also produces a more consistent bead profile, which is critical when the cladding must meet strict dimensional tolerances for subsequent drilling of the tube holes. However, the deposition rate is lower, and the process requires more passes, which increases the risk of distortion and residual stress accumulation. The paper correctly identifies that both processes have their place, and the selection must be driven by the specific design requirements and manufacturing constraints of each project.

Key Technical Challenges and Failure Modes

The paper highlights several problems that can occur during tube sheet surfacing, and I want to emphasize these because they are the ones that cause sleepless nights for plant managers and quality engineers.

  1. Lack of Fusion and Lack of Penetration: This is the most common defect in both processes. In strip ESW, the high heat input can cause the strip to melt unevenly, leading to incomplete fusion at the edges of the bead. In hot-wire TIG, improper wire feed speed or torch angle can result in lack of penetration at the root. The consequences are severe: any lack of fusion in a nuclear cladding is a potential leak path for primary coolant, and it is unacceptable per ASME Section III and RCC-M requirements.
  2. Slag Entrapment: Strip ESW relies on a flux layer that melts and forms a slag cover. If the slag is not properly controlled, it can become entrapped in the weld metal, leading to non-metallic inclusions that degrade corrosion resistance and mechanical properties. I have seen this happen on vessel cladding, and the repair process—grinding, re-welding, and re-testing—is both costly and time-consuming.
  3. Magnetic Arc Blow: As mentioned, this is a significant issue in strip ESW. The high currents used (typically 800–1500 A) generate strong magnetic fields that can deflect the arc, causing the bead to meander and resulting in poor fusion. Mitigation strategies include using a magnetic field controller, arranging the return leads symmetrically, and degaussing the workpiece before welding.
  4. Distortion and Residual Stress: The tube sheet is a thick component, but the cladding process still introduces significant heat input. In the EPR project, where hot-wire TIG is used, the lower heat input per pass helps reduce distortion, but the cumulative effect of many passes can still cause the tube sheet to bow. This is critical because the tube sheet must remain flat to within tight tolerances for the subsequent drilling and tube expansion operations.
  5. Cracking: Nickel-based alloys are susceptible to hot cracking, particularly in the weld metal and the heat-affected zone (HAZ). The paper notes that proper preheat and interpass temperature control, combined with low-impurity filler materials, are essential to prevent this. In my experience, the most common cause of cracking in nickel alloy cladding is sulfur and phosphorus contamination from the base metal or the filler wire, so strict control of these elements is non-negotiable.

Engineering Practice Insights and Lessons Learned

Drawing on my own experience with similar surfacing work on pressure vessels and heat exchangers, I want to share some practical observations that go beyond what the paper explicitly states.

Summary and Reflection

This paper provides a valuable comparison of two surfacing methods for nuclear steam generator tube sheets, and it highlights the key technical challenges that must be addressed to achieve high-quality cladding. For me, the most important takeaway is that process selection is not a one-size-fits-all decision. The CPR1000 and EPR projects chose different methods because their design requirements and manufacturing constraints were different. As an engineer, I must always ask: What is the geometry? What is the required deposition rate? What are the quality requirements? What is the schedule? Only by answering these questions can I make an informed decision. The paper also reminds me that even with the best process, the devil is in the details—preheat control, consumable quality, magnetic field management, and NDT strategy all play a critical role in the final outcome. For anyone involved in nuclear component fabrication, this paper is a useful reference, but it should be read in conjunction with the applicable codes and standards, such as ASME Section III and RCC-M, to fully understand the requirements. In the end, the success of a tube sheet surfacing operation depends on the combination of sound process design, rigorous quality control, and, most importantly, experienced personnel who understand the nuances of the materials and processes involved.