ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Composition Effects on the Properties of Hot Rolling Mill Roll Hardfacing Layers

Introduction and Literature Context

This 1991 study from Xi'an Jiaotong University and Anshan Iron and Steel Research Institute addresses a question I have wrestled with on more than one shop floor: how do you balance wear resistance against thermal fatigue when you are rebuilding a rolling mill roll? The paper is a classic piece of applied metallurgy, and its core message remains as valid today as it was three decades ago. The authors set out to establish the relationship between the chemical composition of a hardfacing alloy, the resulting microstructure, and the service performance of the rebuilt roll surface.

The paper opens with a statement that will resonate with anyone who has run a rolling mill: the hardfacing layer's microstructure and properties determine the production performance of the mill, and the wear resistance and thermal fatigue resistance change in opposite directions as the composition changes. This is the fundamental trade-off. If you push the alloy too hard for wear resistance, you get a hard, brittle surface that cracks under thermal cycling. If you soften it to survive thermal shock, you lose the abrasion resistance that the roll needs to hold its profile.

Core Technical Points

The Composition–Microstructure–Property Triangle

The authors studied several hardfacing alloy systems and examined their microstructures using optical metallography, scanning electron microscopy, and X-ray diffraction. The key findings can be summarised as follows.

Parameter Observation Engineering Implication
Matrix phase Austenite, martensite, or a mixture depending on alloy content Austenite gives toughness and thermal fatigue resistance; martensite gives hardness but reduces crack resistance
Carbide type Cr7C3, Cr23C6, or complex Nb/V carbides Cr7C3 provides excellent abrasion resistance; finer carbides improve toughness
Carbide distribution Network, blocky, or dispersed Dispersed fine carbides give the best combination of wear resistance and thermal fatigue life
Alloy content C, Cr, Mo, V, Nb, W in varying amounts Each element shifts the balance between hardness and toughness
Dilution Base metal dilution from the roll substrate High dilution degrades the hardfacing chemistry and must be controlled by welding parameters

The authors proposed that the hardfacing layer's properties are governed by both microscopic factors (carbide type, size, distribution, matrix constitution) and macroscopic factors (residual stress, dilution, layer thickness, and the presence of defects such as cracks and porosity). This is a critical insight for the production engineer. You can design the perfect alloy chemistry, but if you lay it down with the wrong welding parameters, the dilution will change the effective composition, and the residual stress state will determine whether the layer survives the first thermal cycle.

The Wear–Thermal Fatigue Trade-off

The study demonstrated that as the alloy content increases to improve wear resistance, the thermal fatigue resistance decreases. This is the classic dilemma in roll hardfacing. The authors identified the optimum microstructural condition as one where the hard phase particles are fine, uniformly distributed, and embedded in a tough matrix that can accommodate thermal strain without cracking.

Microstructural Condition Wear Resistance Thermal Fatigue Resistance Suitable Application
Coarse primary carbides in martensite High Low Low-temperature, low-impact rolling
Fine dispersed carbides in austenite Moderate High Hot rolling with severe thermal cycling
Eutectic carbides in austenite–martensite Moderate–high Moderate General purpose roll rebuilding
Martensite with no carbides Low High Backup rolls, low wear requirement

The New Alloy System

The paper concludes with the introduction of a newly developed hardfacing alloy system that replaced the previous composition design. This new system achieved a better balance of properties by optimising the carbide type and distribution while maintaining a tough matrix. The authors reported that this new alloy system was superior to the conventional compositions in both wear resistance and thermal fatigue performance.

Integration with Engineering Practice

The Plant Floor Reality

I have seen the consequences of getting this trade-off wrong. On one occasion, a mill rebuilt a pair of work rolls for a hot strip mill using a high-chromium hardfacing alloy that was specified for maximum wear resistance. The rolls went into service, and within three days, the surface had developed a network of thermal fatigue cracks that propagated into the roll body. The mill lost two days of production, and the rolls had to be stripped and rebuilt again. The hardfacing alloy was not the problem; the problem was that the application engineer had not considered the thermal cycling severity of that particular stand.

The lesson is simple: the hardfacing alloy must be selected for the specific service conditions, not for maximum hardness. A roll in a finishing stand sees different thermal cycles and different loads than a roll in a roughing stand. A roll in a pipe mill's forming section sees different conditions again. The composition that works for one may fail catastrophically in another.

Welding Process Control

The paper's emphasis on dilution and residual stress is well placed. In practice, I have found that the following process controls are essential for achieving the intended hardfacing layer properties.

  1. Preheat and interpass temperature control to prevent hydrogen-induced cracking in the hardfacing layer and to manage residual stress.
  2. Controlled welding parameters to limit dilution from the substrate. This is particularly critical for the first layer, where dilution can be 30% or more.
  3. Post-weld heat treatment or stress relief where the roll geometry and alloy system permit.
  4. Layer thickness control to ensure that the final surface composition is representative of the intended hardfacing alloy, not a mixture of the alloy and the substrate.

Inspection and Quality Control

The paper's identification of defects such as cracks and porosity as macroscopic factors affecting performance is directly relevant to quality control. In my experience, the following inspection regime is appropriate for roll hardfacing.

Inspection Method Purpose Acceptance Criteria
Visual inspection Detect surface cracks, porosity, and lack of fusion No cracks, no open porosity
Magnetic particle testing Detect surface-breaking cracks No indications exceeding 1 mm
Ultrasonic testing Detect lack of fusion and subsurface defects No defects exceeding 2 mm equivalent
Hardness testing Verify hardfacing layer hardness Within specified range
Metallographic examination Verify microstructure and carbide distribution As specified for the alloy system
Chemical analysis Verify composition, accounting for dilution Within specified range

Key Questions and Reflections

What the Paper Does Not Tell You

The paper is a laboratory study, and it does not address the full range of practical issues that arise in roll hardfacing. It does not discuss the effect of the roll substrate composition on the hardfacing layer, which is critical because dilution changes the effective alloy content. It does not address the issue of roll geometry and the resulting residual stress distribution. It does not discuss the economics of roll rebuilding versus replacement, which is a major factor in deciding whether to hardface at all.

What I Would Ask the Authors

If I were sitting across the table from these authors, I would ask them the following questions.

  1. What was the dilution level in your test specimens, and how did you control it?
  2. Did you perform thermal fatigue testing that simulated actual rolling conditions, or did you rely on laboratory thermal cycling?
  3. What was the failure mode in the field trials of the new alloy system, and how did it compare with the conventional alloys?
  4. How did the hardfacing layer perform in terms of roll surface profile retention, which is the real measure of roll performance?

The Practical Judgment

The paper's value lies in its systematic approach to the composition–microstructure–property relationship. It confirms what experienced hardfacing engineers know intuitively: there is no single "best" hardfacing alloy. There is only the best alloy for a given set of service conditions. The paper provides a framework for thinking about that relationship, and that framework is still useful today.

Study Insights and Implications

For the Welding Engineer

The key takeaway for the welding engineer is that the hardfacing alloy selection must be based on the service conditions, not on a generic hardness specification. The welding parameters must be controlled to achieve the intended dilution level, and the preheat and interpass temperatures must be managed to control residual stress and prevent cracking.

For the Quality Engineer

The quality engineer must understand that the hardfacing layer's properties are determined by both the alloy composition and the welding process. Inspection must verify not only the surface hardness but also the microstructure and the absence of defects. A hardness test alone is insufficient to confirm that the hardfacing layer will perform in service.

For the Production Manager

The production manager must recognise that roll hardfacing is a specialised operation that requires skilled welders, controlled welding parameters, and rigorous inspection. Cutting corners on any of these will result in premature roll failure, lost production, and increased costs. The cost of a quality hardfacing job is always less than the cost of a failed roll.

Summary and Conclusion

This 1991 study remains a valuable reference for anyone involved in roll hardfacing because it addresses the fundamental trade-off between wear resistance and thermal fatigue resistance that governs the performance of hardfaced rolls. The authors correctly identified that both microscopic factors (carbide type, size, distribution, matrix constitution) and macroscopic factors (dilution, residual stress, defects) determine the service performance of the hardfacing layer. The introduction of a new alloy system that balanced these factors represents a practical advance in roll hardfacing technology.

The study's limitations are also instructive. It does not address the full range of practical issues that arise in roll hardfacing, including the effect of substrate composition, roll geometry, and the economics of roll rebuilding. These are the issues that the practising engineer must consider when applying the paper's findings.

In my experience, the most important lesson from this study is that hardfacing alloy selection must be based on the specific service conditions of the roll, not on a generic hardness specification. The alloy that works for one application may fail catastrophically in another. The engineer who understands this will avoid the costly mistakes that I have seen too many times on the plant floor.