Friction and Wear Properties of Nanocrystalline Surface Layers on Hardfacing Deposits
The Paper's Core Contribution
This 2014 study by Badema and colleagues at the Academy of Armored Forces Engineering addresses a problem I have wrestled with for decades: how do you improve the surface properties of a hardfaced component without changing its bulk composition? The answer they propose is surface nanocrystallization through pre-stress rolling, and their results are genuinely impressive. Using transmission electron microscopy and scanning electron microscopy, they confirmed that the process creates a nanocrystalline layer approximately 10 micrometers thick, with grain sizes below 100 nanometers. At the very surface, the average grain size is around 10 nanometers.
The mechanical property improvements are striking. Nanoindentation testing showed that the hardness of the outermost nanocrystalline layer is approximately three times that of the original hardfacing deposit. In dry friction testing, the friction coefficient of the nanocrystallized samples decreased by 10 percent compared to the original hardfacing, and the wear volume decreased by 25 to 30 percent. The wear mechanism changed from a combination of abrasive and adhesive wear to predominantly abrasive wear.
Why This Matters for Pipe Manufacturing
| Property | Original Hardfacing | After Surface Nanocrystallization |
|---|---|---|
| Surface grain size | Micron-scale | 10-100 nm |
| Layer thickness | N/A | ~10 μm |
| Surface hardness | Baseline | ~3x baseline |
| Friction coefficient | Baseline | -10% |
| Wear volume | Baseline | -25% to -30% |
| Wear mechanism | Abrasive + adhesive | Predominantly abrasive |
In the pipe industry, we hardface forming rolls, sizing rolls, and mandrel bars to resist wear, but the surface finish is often the limiting factor. A hardfaced roll that wears uniformly is acceptable; a hardfaced roll that develops a rough, adhesive-worn surface will mark the pipe surface and require immediate dressing. The ability to create a nanocrystalline layer on the surface of a hardfaced deposit offers a way to improve both wear resistance and surface finish without changing the underlying material.
Practical Application on the Shop Floor
I have seen pre-stress rolling used on roll surfaces in pipe mills, and the results are consistent with this paper. The process is simple — a hardened roller is pressed against the surface with a controlled preload while the component rotates. The plastic deformation at the surface creates a gradient of grain refinement, with the finest grains at the outermost surface. The key parameters are the preload force, the number of passes, and the roller geometry.
The paper's finding that the wear mechanism changes from abrasive-plus-adhesive to purely abrasive is significant. Adhesive wear is the enemy of surface finish in pipe forming — it causes material transfer from the roll to the pipe, creating pick-up marks and galling. By eliminating the adhesive component, the nanocrystalline surface maintains its finish for much longer.
Veteran's Reflection
The paper's conclusion that grain refinement leads to high hardness and low plasticity, which in turn improves friction and wear performance, is a fundamental insight. But I would add a practical caveat: the nanocrystalline layer is only 10 micrometers thick. In a pipe mill environment, where forming rolls experience high contact stresses and occasional impact loads, a 10-micrometer layer can be worn through relatively quickly. The real value is in the gradient — the nanocrystalline layer sits on top of a plastically deformed zone that extends deeper into the material, providing a gradual transition in properties rather than a sharp interface.
For my own operations, I see this technology as most valuable for sizing rolls and finishing passes, where surface finish is critical and wear rates are relatively low. For roughing passes, where the material is subjected to severe abrasion and impact, I would still rely on bulk hardfacing with carbide particles. The combination — bulk hardfacing for wear resistance, surface nanocrystallization for finish — is the optimal solution.
The practical advice I give to young engineers: never dismiss a surface treatment because it is only 10 micrometers thick. In tribology, the surface is where the action is. A 10-micrometer layer with three times the hardness can double the service life of a finishing roll, and the cost of the treatment is a fraction of the cost of the roll itself.
Zhuojin Pipe Fitting Co., Ltd