ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Wear-Resistant Overlay Welding Materials in the Cement Industry: Application Status and Development Prospects

Literature Overview

The paper by Wei Jianjun and colleagues from Zhengzhou Research Institute of Mechanical Engineering provides a comprehensive review of wear-resistant overlay welding materials used in cement machinery. The authors analyze the working conditions and failure modes of key components such as extrusion rollers, vertical mill rollers, grinding discs, crusher hammers, and hammer discs. They then summarize the application of overlay welding technology for both composite manufacturing (new components) and remanufacturing (repair of worn components), highlighting the significant economic and environmental benefits achieved through extended service life.

Core Technical Points

The paper identifies the following key wear components and their failure mechanisms:

Component Working Condition Primary Failure Mode
Extrusion roller High compressive stress, abrasive wear Surface spalling, fatigue cracking
Vertical mill roller Abrasive wear with impact Surface pitting, material loss
Grinding disc Abrasive wear, high temperature Surface grooving, erosion
Crusher hammer Impact and abrasive wear Chipping, material loss
Hammer disc Abrasive wear Surface wear, dimensional loss

The application of overlay welding technology has resulted in service life improvements of two to five times for these components, depending on the specific wear mechanism and the overlay material selected. The economic benefits are substantial, considering the high cost of replacement parts and the downtime associated with maintenance.

Process and Standards Analysis

The paper emphasizes the importance of matching the overlay material to the specific wear mechanism. For abrasive wear dominated by hard particles, high-chromium iron-based alloys with hard carbides are typically used. For impact-dominated wear, a more ductile matrix with dispersed hard phases may be preferred to prevent chipping. The trade-off between wear resistance and crack resistance is a central theme, as excessive hardness often leads to cracking during welding or in service.

From a manufacturing perspective, the selection of overlay welding process (submerged arc welding, flux-cored arc welding, plasma transferred arc welding) depends on the component geometry, required deposition rate, and allowable dilution. The dilution rate directly affects the final composition and properties of the overlay layer, and must be carefully controlled to achieve the desired hardness and wear resistance.

Engineering Practice Integration

In my experience with cement plant maintenance and component remanufacturing, the practical benefits of overlay welding are undeniable. I have witnessed extrusion rollers that were originally expected to last 6 months being returned to service after overlay welding and lasting over 18 months. The key to success lies in proper pre-weld preparation, including thorough cleaning and preheating to prevent hydrogen-induced cracking, and careful post-weld heat treatment to relieve residual stresses.

However, I have also seen failures where overlay welding was applied without adequate consideration of the substrate material. For example, welding a high-hardness overlay on a low-alloy steel substrate without proper preheating resulted in cracking at the interface and subsequent delamination. The paper's emphasis on studying the wear mechanism and balancing wear resistance with crack resistance is crucial for avoiding such failures.

Key Questions and Reflections

The paper raises several important questions:

  1. How can the wear mechanism be accurately identified for each specific component in a given cement plant?
  2. What is the optimal overlay thickness for different wear conditions, balancing cost and service life?
  3. How can the crack resistance of high-hardness overlay materials be improved without compromising wear resistance?

These questions highlight the need for a systematic approach to material selection and process development, rather than relying on generic solutions.

Study Insights and Implications

This review provides a valuable framework for engineers involved in the design, manufacturing, and maintenance of cement machinery. The key insight is that overlay welding is not a one-size-fits-all solution; it requires a thorough understanding of the specific wear mechanism and the development of tailored material and process combinations. The economic and environmental benefits of extending component service life through overlay welding are significant, particularly in the context of sustainable manufacturing and resource conservation.

The future direction outlined in the paper—expanding the application range, deepening the understanding of wear mechanisms, and developing materials that balance wear resistance and crack resistance—aligns with the broader trend toward remanufacturing and circular economy principles. For practitioners, the practical takeaway is to invest in the development of in-house overlay welding capabilities and to establish robust quality control procedures to ensure the reliability of remanufactured components.

In conclusion, this paper serves as an essential reference for anyone involved in the wear management of cement machinery, offering both a comprehensive overview of current practices and a clear roadmap for future development.