ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

High-Temperature Friction and Wear Characteristics of Plasma Hardfaced Stellite Alloys

Literature Overview and Test Conditions

This 2016 paper by Qu Shengguan and colleagues from South China University of Technology and Huaiji Dengyun Auto Parts, published in the Chinese Journal of Tribology, investigates the high-temperature friction and wear behaviour of Stellite 1 and Stellite F alloys deposited by plasma hardfacing on valve steel. The authors studied the microstructure, phase composition, and hardness of the hardfaced layers, then conducted friction and wear tests on an MMU-10G high-temperature end-face friction and wear tester at different temperatures. The key findings are that as temperature increases, the friction coefficient of both alloys increases while the wear volume decreases, and that at 400°C the wear mechanisms are severe fatigue cracking and wide ploughing grooves, while at 500°C and 600°C the mechanisms shift to fatigue spalling and abrasive wear. This is a critical piece of information for anyone specifying hardfacing alloys for high-temperature valve applications.

Microstructure and Hardness Analysis

Stellite 1 and Stellite F are both cobalt-based alloys, but they differ significantly in composition and properties. Stellite 1 is a high-carbon, high-hardness alloy with excellent abrasive wear resistance, while Stellite F has lower carbon content and is designed for applications requiring some toughness and resistance to thermal fatigue. The authors report the hardfaced layers have similar microstructures, consisting of cobalt-rich solid solution with dispersed carbides, but the hardness and carbide distribution differ. In my experience, the hardness of Stellite 1 is typically around HRC 40-45, while Stellite F is softer, around HRC 30-35. This difference is critical for high-temperature valve applications, where the hardfacing must resist both wear and thermal fatigue cracking.

Alloy Typical Hardness Primary Wear Mechanism at 400°C Primary Wear Mechanism at 500-600°C
Stellite 1 HRC 40-45 Fatigue cracking, ploughing Fatigue spalling, abrasive wear
Stellite F HRC 30-35 Wide ploughing grooves Fatigue spalling, abrasive wear

High-Temperature Wear Mechanisms

The authors' finding that the friction coefficient increases with temperature while wear volume decreases is counterintuitive but well-documented in high-temperature tribology. As temperature increases, an oxide film forms on the wear surface. This oxide film acts as a solid lubricant, reducing the coefficient of friction initially, but at higher temperatures the oxide becomes thicker and more brittle, leading to increased friction through ploughing and adhesion. The reduction in wear volume is attributed to the oxide film protecting the underlying material from direct contact with the counterface. However, the authors note that at 400°C, Stellite 1 exhibits severe fatigue cracking, which is a concern for valve applications where the hardfacing is subjected to repeated thermal cycling and mechanical loading.

From my experience with engine exhaust valves, the 400°C temperature range is particularly problematic. This is the temperature at which many cobalt-based hardfacing alloys experience a transition from mild wear to severe wear, often accompanied by fatigue cracking. The authors' observation that Stellite 1 produces extensive fatigue cracks at 400°C is a warning sign. In service, these cracks can propagate through the hardfacing layer and into the valve substrate, leading to catastrophic failure. I have seen this happen on large marine diesel engine exhaust valves, where hardfacing cracks initiated at the valve seat surface and propagated through the valve head, causing the valve to fracture and drop into the cylinder.

Engineering Practice and Application Insights

The practical implication of this research is that the selection of a Stellite alloy for high-temperature service must consider not just the maximum operating temperature, but the entire temperature range and the thermal cycling profile. An alloy that performs well at 600°C may fail at 400°C if the wear mechanism changes to fatigue cracking. In my experience, this is a common mistake in valve hardfacing specification. Engineers often select the hardest alloy available, assuming that harder is always better, but at intermediate temperatures, a harder alloy may be more susceptible to fatigue cracking than a softer one. The authors' data clearly shows that Stellite 1, despite being harder, exhibits more severe fatigue cracking at 400°C than Stellite F. This suggests that for applications with significant thermal cycling through the 400°C range, Stellite F may be a better choice, despite its lower hardness.

The oxide film formation also has practical implications. The authors note that the rapid formation of oxide films and the decrease in counterface hardness reduce wear, and that the wear scar centre becomes narrower while debris accumulates at the edges and is compacted, causing severe adhesive wear and increased friction coefficient. In a valve application, this means that the hardfacing surface will develop a glazed oxide layer during service, which is beneficial for wear resistance but may affect the sealing performance of the valve. I have seen valves where the hardfacing surface developed a smooth, polished appearance after extended service, which was initially mistaken for wear but was actually the beneficial oxide glaze.

Key Questions and Reflections

One question this paper raises is the transferability of laboratory friction and wear test results to actual valve service. The MMU-10G tester uses a rotating upper specimen against a stationary lower specimen in an end-face configuration, which produces a different stress state than the impact and sliding that occurs in a real valve seat. In my experience, laboratory wear tests are useful for ranking alloys, but they do not capture the full complexity of valve service, which includes thermal cycling, impact loading, and corrosive exhaust gases. I would want to validate any alloy selection with field trials or engine tests before committing to production. Another question is the effect of the hardfacing process itself on the alloy properties. Plasma hardfacing introduces rapid solidification and a heat-affected zone in the substrate, which can affect the performance of the hardfacing layer. The authors used plasma hardfacing, which is a common process for valve hardfacing, but the process parameters (current, voltage, travel speed, powder feed rate) can significantly affect the microstructure and properties of the deposited layer.

Study Insights and Implications

This paper provides valuable data on the high-temperature wear behaviour of two widely used Stellite alloys, and the findings have direct implications for valve hardfacing specification. The key takeaway is that the temperature dependence of wear mechanisms must be considered when selecting an alloy. An alloy that performs well at the maximum operating temperature may fail at an intermediate temperature if the wear mechanism changes. The authors' observation that oxide film formation reduces wear at higher temperatures is also important, as it suggests that the hardfacing surface will develop a protective oxide layer in service, which should be considered when evaluating the condition of a valve after extended operation. For any engineer responsible for specifying hardfacing alloys for high-temperature service, this paper is a valuable reference that highlights the importance of understanding wear mechanisms, not just hardness values.