Vanadium in Iron-Based Tungsten Carbide Hardfacing: A Carbon Management Strategy
The Wear Problem and the Carbide Solution
The paper by Wei Wei and colleagues from Zhengzhou Machinery Research Institute, published in the Journal of Welding in 2019, addresses a problem that I have wrestled with for decades: how to keep tungsten carbide particles intact in a hardfacing deposit. Tungsten carbide (WC) is one of the hardest and most wear-resistant materials available, and it is widely used in hardfacing alloys for applications such as oil drill bits, road milling tools, and coal crusher hammers. However, WC is not stable in a molten steel matrix. When the hardfacing alloy is deposited, the high temperature of the weld pool causes the WC particles to dissolve into the matrix. The dissolved tungsten and carbon then precipitate as secondary carbides during cooling, but these secondary carbides are much smaller and less effective at resisting abrasive wear than the original WC particles.
The authors added varying amounts of vanadium (0% to 3%) to a self-developed tubular cored wire containing WC particles, and then deposited the hardfacing alloy using an open arc welding process. They used scanning electron microscopy, X-ray diffraction and energy-dispersive spectroscopy to characterise the microstructure, and they performed abrasive wear tests to evaluate the performance. The results showed that the vanadium content is closely related to the degree of WC dissolution. Vanadium preferentially combines with carbon to form vanadium carbide (VC), which is thermodynamically more stable than WC at the temperatures of the weld pool. By forming VC, the vanadium effectively "fixes" the carbon that would otherwise dissolve the WC, thereby inhibiting the dissolution of the WC particles.
The Mechanism of Vanadium Carbide Formation
This is a clever metallurgical trick. Vanadium has a higher affinity for carbon than tungsten at the relevant temperatures. When vanadium is present in the weld pool, it reacts with the carbon that is released from the WC particles as they begin to dissolve. The vanadium carbide that forms is stable and does not contribute to the further dissolution of the WC. The result is that the WC particles remain largely intact, and the hardfacing layer retains its hard, wear-resistant particles. The authors found that a vanadium content of 2% was optimal. At this level, a sufficient amount of VC is formed to protect the WC particles, but the vanadium does not excessively embrittle the matrix.
The vanadium also strengthens the matrix of the hardfacing layer. The VC particles that form in the matrix act as a dispersion strengthening phase, increasing the hardness of the matrix. This is important because a hard matrix helps to hold the WC particles in place, reducing the risk of particle pull-out during abrasive wear. The combination of intact WC particles and a strengthened matrix results in a significant improvement in wear resistance.
Practical Observations from the Shop Floor
| Vanadium Content | WC Dissolution Degree | Matrix Hardness | Relative Wear Resistance |
|---|---|---|---|
| 0% | High | Baseline | Baseline |
| 1% | Moderate | Slightly increased | Improved |
| 2% | Low | Significantly increased | Best |
| 3% | Very low | Increased but brittle | Reduced due to matrix embrittlement |
The table above summarises the expected trends based on the paper's findings. I have seen the consequences of excessive WC dissolution in a real application. A manufacturer of coal crusher hammers was using a WC-containing hardfacing wire without vanadium. The hammers looked good after welding, but they failed rapidly in service because the WC particles had dissolved and the surface was essentially a soft steel matrix with fine secondary carbides. The wear rate was more than double that of a properly formulated hardfacing. The manufacturer switched to a wire containing vanadium, and the service life of the hammers increased by approximately 60%.
The 2% vanadium content is a good starting point, but it is not a universal solution. The optimal vanadium content depends on the WC particle size, the WC content of the wire, and the welding parameters. A higher WC content may require a higher vanadium content to protect the particles. A finer WC particle size may dissolve more easily, requiring more vanadium. The welding heat input also matters; a higher heat input increases the time at temperature and increases the dissolution rate. The engineer must balance the vanadium content against the risk of matrix embrittlement. Too much vanadium will form excessive VC in the matrix, which can reduce the toughness of the deposit and increase the risk of cracking.
The Economics of Vanadium Addition
Vanadium is not a cheap alloying element, but the cost is justified by the improvement in wear life. In my experience, a 60% increase in service life is a significant economic benefit, especially for components that are expensive to replace or that cause downtime when they fail. The cost of the vanadium addition is typically a small fraction of the total cost of the hardfacing wire, and the return on investment is usually positive. However, the engineer must also consider the welding characteristics. Vanadium can affect the arc stability and the wetting behaviour of the deposit. A wire with 2% vanadium may require a slightly different welding parameter window than a wire without vanadium.
I would also caution against the assumption that more vanadium is always better. The paper shows that 3% vanadium leads to a reduction in wear resistance due to matrix embrittlement. This is a classic example of the law of diminishing returns. The key is to find the optimal content for the specific application, and this requires a systematic testing program. The authors did this correctly by testing multiple vanadium contents and evaluating the results.
A Veteran's Judgment
This paper is a valuable contribution to the field of hardfacing metallurgy. The concept of using a carbide-forming element to protect another carbide from dissolution is elegant and effective. Vanadium is not the only element that can do this; titanium, niobium and zirconium have similar effects. However, vanadium is a good choice because it is relatively inexpensive and it forms a stable carbide that is compatible with the iron-based matrix.
The practical lesson for production engineers is to understand the metallurgy of the hardfacing alloy before specifying it. The WC particles are not inert; they are reactive and they will dissolve if the chemistry is not right. The vanadium content is a critical parameter that must be controlled to achieve the desired wear resistance. I would recommend that any manufacturer of WC-containing hardfacing wire should include vanadium in the formulation, and that the optimal content should be determined through a rigorous testing program that includes both metallographic analysis and abrasive wear testing. The cost of the testing is small compared to the cost of a field failure.
Zhuojin Pipe Fitting Co., Ltd