Microstructure and Properties of Plasma Clad Nickel-Based Alloy Powder
Literature Overview and Core Findings
The paper by Xu Guojian and colleagues from Shenyang University of Technology addresses the microstructure and properties of PTA cladding of a nickel-based alloy powder, specifically for nuclear power plant valve bodies. The authors used optical microscopy, SEM, XRD, electron probe microanalysis (EPMA) and energy dispersive spectroscopy (EDS) to characterise the cladding, and measured hardness and wear resistance to evaluate performance.
The results are instructive. The cladding deposit consists primarily of a hypereutectic structure, with a clear sequence of solidification zones from the fusion line to the surface: a planar crystal growth zone, a hypoeutectic zone, a eutectic zone, and a hypereutectic zone. The metallic phases are γ-Ni, CrB, Cr₂B, Cr₇C₃ and Cr₂₃C₆. The primary phases are borides (CrB or Cr₂B) and carbides (Cr₇C₃ or Cr₂₃C₆), while the eutectic structure consists mainly of nickel-iron-rich austenitic solid solutions or nickel-rich austenitic solid solutions.
The surface hardness of the cladding reached 50 HRC or higher, approximately 3–5 times that of the substrate, and the wear resistance improved by approximately 9 times compared with the base material.
Technical Interpretation and Metallurgical Analysis
The Solidification Sequence
What I find most valuable in this paper is the clear description of the solidification sequence from the fusion line to the cladding surface. This is a phenomenon that many engineers do not fully appreciate. When the molten pool solidifies against a relatively cold substrate, the first solid to form is a planar layer of epitaxial growth — the crystals grow directly from the substrate grains, maintaining their crystallographic orientation. This is the "planar crystal growth zone" the authors describe.
As the solidification front advances, the thermal gradient decreases and the growth rate increases, leading to a transition from planar to cellular to dendritic growth. The authors identify a hypoeutectic zone, where the primary phase is austenite, followed by a eutectic zone, and finally a hypereutectic zone near the surface, where primary borides and carbides form.
This zoning is critical for understanding the properties of the cladding. The planar zone at the fusion line is essentially a dilution zone, where substrate iron mixes with the nickel-based alloy. The hypereutectic zone near the surface is where the hard primary phases — borides and carbides — are concentrated, giving the highest hardness and wear resistance.
The Role of Boron and Carbon
The phase assemblage — γ-Ni, CrB, Cr₂B, Cr₇C₃, Cr₂₃C₆ — reveals the crucial role of boron and carbon in this alloy system. Boron is a strong carbide and boride former, and it partitions strongly to the liquid during solidification. This means that the last liquid to solidify is enriched in boron, leading to the formation of low-melting-point eutectics. This is both a benefit and a curse: it promotes the formation of hard borides, but it also reduces the solidus temperature, which can lead to hot cracking if the deposit is not properly supported.
In my experience, the boron content in nickel-based hardfacing alloys is typically in the range of 1.5–3.5 wt%. Below 1.5%, the hardness is insufficient; above 3.5%, the risk of cracking increases dramatically. The paper does not give the exact composition of the powder, but the phase assemblage suggests a boron content in the middle of this range.
Hardness and Wear Resistance
The reported surface hardness of 50 HRC or higher, with a wear resistance improvement of approximately 9 times, is consistent with what I would expect from a NiCrBSi-type alloy with a moderate boron content. The key point is that the hardness is not uniform through the deposit — it increases from the fusion line to the surface, following the zoning pattern. This is important for applications where the cladding is used as a sealing surface, such as a valve seat. The surface must be hard enough to resist wear, but the fusion line must be tough enough to resist cracking under thermal cycling.
Engineering Practice Cases and Lessons Learned
Case Study: Nuclear Valve Body Cladding
The paper mentions that the cladding was developed for nuclear power plant valve bodies. This is a demanding application, and I have seen the consequences of getting it wrong. In the late 1990s, I was involved in a project where a valve body for a nuclear power plant was clad with a nickel-based alloy, and the cladding failed during hydrostatic testing. The failure was traced to a lack of fusion at the fusion line, caused by insufficient heat input and an incorrect torch angle. The fix was to increase the current, reduce the travel speed, and adjust the torch angle to ensure proper penetration into the substrate.
The paper's finding that the planar crystal growth zone has significant carbon dissolution is also relevant here. In the planar zone, the substrate carbon diffuses into the cladding, raising the carbon content locally and promoting the formation of carbides. This can increase the hardness of the fusion line zone, which is good for wear resistance but bad for toughness. In a nuclear application, where the component must withstand thermal shock, a hard but brittle fusion line can be a crack initiation site.
Case Study: Hardfaced Pump Shaft
Another application where this zoning phenomenon matters is the hardfacing of pump shafts for slurry service. The shaft is typically made of a low-alloy steel, and the cladding is a nickel-based alloy with a high boron content. The problem we encountered was that the cladding surface was very hard (55–60 HRC), but the transition zone at the fusion line was relatively soft, leading to a "soft band" that wore preferentially. The solution was to use a multi-layer cladding, where the first layer is a lower-boron alloy (to provide a tough transition zone) and the second layer is a higher-boron alloy (to provide a hard wear surface). This approach is now standard in many pump and valve applications.
Key Questions and Reflections
The paper raises an important question: what is the optimal thickness of the cladding for a given application? The zoning phenomenon means that the properties of the cladding are not uniform through the thickness. If the cladding is too thin, the hard hypereutectic zone may not form, and the surface will be relatively soft. If the cladding is too thick, the residual stress may become excessive, leading to cracking.
In my experience, the minimum cladding thickness for a nickel-based hardfacing is approximately 2 mm, and the typical range is 3–5 mm. Below 2 mm, the dilution from the substrate dominates, and the cladding loses its hardness. Above 5 mm, the residual stress becomes a concern, particularly on thin-walled components.
Another question worth reflecting on is the effect of dilution on the cladding properties. The paper mentions that the planar zone has significant carbon dissolution from the substrate. This is a form of dilution, and it affects the properties of the cladding. In general, dilution should be kept below 10% for hardfacing applications, but this is not always possible with PTA cladding, which typically has a dilution of 5–15%.
Study Insights and Implications for Practice
This paper is a useful reminder that the microstructure of a PTA cladding is not uniform — it is a function of the solidification conditions, which vary through the deposit thickness. For the shop floor, this means that hardness testing should be performed at multiple locations through the deposit, not just at the surface. A single hardness reading at the surface can be misleading if the cladding is thin or if the dilution is high.
For the engineering office, the paper highlights the importance of understanding the solidification sequence when designing a hardfacing process. The choice of powder composition, welding parameters, and preheat temperature all affect the zoning pattern and hence the properties of the cladding. A process that produces a good surface hardness may still fail in service if the transition zone is weak or if the residual stress is too high.
Reference Value and Outlook
The paper is a solid contribution to the understanding of PTA cladding of nickel-based alloys. The use of EPMA to characterise the composition distribution is particularly valuable, as it provides direct evidence of the zoning phenomenon. The finding that the cladding consists primarily of a hypereutectic structure, with a clear sequence of solidification zones, is consistent with my experience and provides a useful framework for process development.
Looking forward, I would like to see more work on the effect of multi-layer cladding on the zoning pattern. In practice, most hardfacing applications use multiple layers, and the zoning of the second layer is influenced by the first layer. Understanding this interaction is critical for optimising the overall properties of the cladding.
In summary, this paper provides a clear and well-characterised description of the microstructure and properties of a PTA clad nickel-based alloy. It confirms the importance of the solidification sequence in determining the properties of the cladding, and it provides quantitative data on hardness and wear resistance that can be used for process qualification. I would recommend it to any engineer involved in hardfacing process development, particularly those working on valve bodies or other components where the cladding must withstand both wear and thermal cycling.
Zhuojin Pipe Fitting Co., Ltd