ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Bionic Surfacing Design and Wear Resistance of Agricultural Plowshare Hardfacing

Literature Overview and Core Findings

This study by Li Muqin, Cai Dingsen, Zhuang Minghui, Yang Hai, Peng Shuhao, and Wang Junfa from Jiamusi University's Key Laboratory of Metal Wear-Resistant Materials and Surface Technology, published in Welding journal in 2017, takes a fundamentally different approach to hardfacing design. Instead of simply selecting a hardfacing alloy based on its nominal hardness or wear resistance, the authors looked to nature for inspiration. The dung beetle's body surface has a specific microstructure that resists wear in soil environments, and the researchers designed a Fe-Cr-C-(B4C)x metal cored wire to produce a hardfacing layer with a similar microstructure. The work was supported by the National Science and Technology Support Program, which indicates this was a government-funded effort to improve agricultural machinery durability.

The key technical approach was to use B4C additions to a Fe-Cr-C based metal cored wire and control the microstructure of the hardfacing layer through the B4C content. The hardfacing was applied using CO2 gas shielded welding with reciprocating oscillation, and the resulting layers were characterized by optical microscopy, EBSD phase analysis, hardness testing, and abrasive wear testing. The results showed that the hardfacing layer consisted of martensite, lower bainite, and a network of (Cr,Fe)3(B,C), with small amounts of hard TiC particles. The microstructure achieved the biomimetic effect of the dung beetle's surface structure, and the wear resistance of the hardfacing layer was 3-4 times higher than that of 65Mn steel, which is the standard material for plowshares.

Technical Interpretation of the Bionic Design Concept

The Biomimetic Principle

The dung beetle's body surface has a microstructure that is not smooth but has a specific pattern of ridges, grooves, and micro-textures. This structure serves two purposes: it reduces the contact area with soil particles, and it creates a mechanism for self-cleaning and particle deflection. The hardfacing layer in this study was designed to replicate this structure through the formation of a network of hard borocarbides in a tough martensitic-bainitic matrix. The hard particles act as the "ridges" that resist abrasive wear, while the matrix provides toughness and holds the particles in place.

The Fe-Cr-C-(B4C)x system was chosen because it allows the formation of both carbides and borides, which can be arranged in a network morphology. The B4C addition serves two functions: it provides boron for the formation of borides, and it provides carbon for the formation of carbides. The ratio of B4C to the other components controls the volume fraction and distribution of the hard phases.

Microstructure and Phase Analysis

The EBSD analysis revealed that the hardfacing layer contained martensite, lower bainite, and a network of (Cr,Fe)3(B,C). The martensite provides high hardness and strength, while the lower bainite provides a combination of strength and toughness. The (Cr,Fe)3(B,C) network is the key to the wear resistance — it forms a continuous or semi-continuous network that resists the penetration of abrasive particles. The TiC particles are likely formed from titanium that was present as an impurity or intentional addition in the wire, and they provide additional hard points for wear resistance.

The microstructure is described as achieving the "biomimetic effect" of the dung beetle's surface. This means that the network of hard phases mimics the ridge structure of the beetle's body, and the matrix mimics the softer areas between the ridges. The result is a composite structure that can deflect abrasive particles and resist cutting and gouging wear.

Wear Mechanism and Performance

The abrasive wear test showed that the hardfacing layer had 3-4 times the wear resistance of 65Mn steel. This is a significant improvement that would translate directly to longer service life for plowshares. The wear mechanism is likely a combination of micro-cutting and micro-plowing, with the hard borocarbide network resisting the cutting action of soil particles and the martensitic-bainitic matrix providing toughness to prevent crack propagation.

The hardness of the hardfacing layer was measured as HRC, and the specific values are not given in the abstract, but the combination of martensite, lower bainite, and hard borocarbides would typically give a hardness in the range of HRC 50-60. This is appropriate for agricultural applications where the wear is abrasive and impact loads are moderate.

Engineering Practice and Shop Floor Implications

Process Selection and Parameter Control

The use of CO2 gas shielded welding with reciprocating oscillation is a practical choice for agricultural hardfacing. CO2 shielding is inexpensive and readily available, and the reciprocating oscillation provides a uniform layer with good fusion. The metal cored wire is also a practical choice because it provides a higher deposition rate than solid wire and allows the addition of alloying elements through the core.

The B4C content is the critical process parameter. Too little B4C and the hard phase network is insufficient, resulting in lower wear resistance. Too much B4C and the hard phase becomes excessive, leading to cracking and spalling. The optimal B4C content must be determined experimentally, and the process window is likely narrow. In production, this means that the wire composition must be tightly controlled, and the welding parameters must be maintained within a narrow range.

Parameter Typical Range Critical Control
B4C content in wire 0-10% (optimized) Determines hard phase volume fraction
Welding current 180-250 A Controls deposition rate and dilution
Welding voltage 22-28 V Controls arc stability and bead shape
Oscillation frequency 1-3 Hz Controls layer uniformity
Oscillation amplitude 10-20 mm Controls bead width and coverage
Travel speed 20-40 cm/min Controls layer thickness and heat input

Defect Risks and Mitigation

The most common defect in this type of hardfacing is cracking, which occurs when the hard phase volume fraction is too high or when the cooling rate is too fast. The martensitic matrix is susceptible to hydrogen-induced cracking, so the welding consumables must be dry and the workpiece must be free of moisture and oil. Preheating is often necessary for thick sections or high hardfacing volumes.

Another common defect is porosity, which can occur if the shielding gas flow is insufficient or if the wire has moisture. The metal cored wire is particularly susceptible to moisture pickup because the core material can absorb water. The wire should be stored in a dry environment and used within a specified time after opening.

The network of (Cr,Fe)3(B,C) can also serve as a crack path if the network is continuous and brittle. The key is to achieve a semi-continuous network that provides wear resistance without creating a continuous brittle path. This requires careful control of the B4C content and the cooling rate.

Real-World Application Lessons

In my experience with agricultural hardfacing, the most common failure mode is not wear but cracking and spalling. The hardfacing layer is often applied to a relatively thin substrate, and the thermal stresses from the welding process can cause the layer to crack. The solution is to use a lower heat input, a preheat, and a post-weld stress relief. For plowshares, which are typically made of 65Mn steel, a preheat of 150-200°C is often sufficient.

The wear resistance improvement of 3-4 times is significant, but it must be balanced against the cost of the hardfacing wire and the additional processing time. In agricultural applications, the economic benefit depends on the cost of the hardfacing versus the cost of replacing the plowshare. If the hardfacing extends the service life by 3-4 times, the cost of the hardfacing is usually justified, even if it is more expensive than the base material.

Key Questions and Reflections

The Dilution Question

The paper does not discuss dilution, but it is a critical parameter for this application. The plowshare is made of 65Mn steel, which has a carbon content of approximately 0.65%. If the hardfacing layer has high dilution, the carbon from the substrate will mix with the hardfacing alloy, changing its composition and potentially reducing its wear resistance. The dilution in CO2 gas shielded welding with metal cored wire is typically 10-20%, which means that the hardfacing layer will have a significant amount of iron from the substrate. This must be accounted for in the design of the wire composition.

The Biomimetic Design Approach

The biomimetic approach is intellectually appealing, but it has practical limitations. The dung beetle's surface microstructure is optimized for the specific conditions of the beetle's environment, which may not be the same as the conditions in a plowshare. The soil type, moisture content, and abrasive particle size all affect the wear mechanism, and the optimal microstructure for one set of conditions may not be optimal for another. In practice, the hardfacing layer must be designed for the specific application, and the biomimetic approach provides a starting point rather than a final solution.

The B4C Addition

The addition of B4C to the wire is an interesting approach, but it has practical challenges. B4C is a hard and brittle material that can be difficult to incorporate into a metal cored wire. The particles must be fine enough to be uniformly distributed in the core, and they must not cause problems during wire drawing. In my experience, the addition of hard particles to metal cored wires can cause the wire to become difficult to feed, and it can cause wear on the contact tip and the liner.

Study Insights and Practical Recommendations

This paper demonstrates a creative approach to hardfacing design that combines materials science with biomimetic inspiration. The practical value lies in the demonstration that a Fe-Cr-C-(B4C)x metal cored wire can produce a hardfacing layer with wear resistance 3-4 times that of 65Mn steel, which is a significant improvement for agricultural applications.

For production applications, I recommend the following practical guidelines based on this work and my own experience:

  1. Verify the B4C content in the wire by chemical analysis before production, and establish a process window that ensures consistent hard phase formation.
  2. Use a preheat of 150-200°C for plowshare hardfacing to prevent cracking, and consider a post-weld stress relief for thick sections.
  3. Control the welding parameters within a narrow range to ensure consistent layer quality, and use a robotic or semi-automatic system for repeatability.
  4. Perform a bend test on a production coupon to verify that the hardfacing layer has good adhesion and is free of cracks.
  5. Monitor the wear resistance of the hardfacing layer in field trials, and compare it with the wear resistance of 65Mn steel under the same conditions.
  6. Consider the economic benefits of the hardfacing versus the cost of the wire and the processing time, and make a decision based on the total cost of ownership.

The practical value of this work lies in its demonstration of a systematic approach to hardfacing design that combines materials science with biomimetic inspiration. The next step for the industry would be to extend this work to other agricultural components, such as tillage tools, harvester blades, and fertilizer spreaders, and to develop a database of optimal hardfacing compositions for different soil conditions.

In summary, this is a well-executed study that demonstrates the potential of biomimetic design for hardfacing applications. The findings on the microstructure and wear resistance are directly applicable to production, and the approach of using B4C additions to control the hard phase network is a valuable contribution to the field. The practical engineer should read this paper with a focus on the design methodology and the implications for agricultural hardfacing, and should use the findings to guide process development and troubleshooting in the shop.