ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Properties of Hardfacing Alloy Layer on K360 Wear-Resistant Steel

Literature Overview and Practical Context

Deng Hanzhong and colleagues from Liaoning Technical University and China Coal Zhangjiakou Coal Mining Machinery Co., Ltd. present an experimental study on the repair of worn K360 wear-resistant steel using flux-cored wire with CO2 gas-shielded hardfacing. K360 is a high-hardness martensitic steel used extensively in mining equipment such as chutes, hoppers, and crusher components, where abrasive wear is the dominant failure mode. The paper examines the microstructure, X-ray diffraction phase analysis, hardness, impact toughness, and abrasive wear resistance of the hardfacing layer. The key finding is that the hardfacing layer has a fine lath martensite structure with dispersed carbides, relatively low hardness, low cold cracking tendency, and good toughness and plasticity. The wear resistance of the hardfacing layer reaches the level of the base metal.

Core Technical Points and Microstructural Analysis

The hardfacing layer microstructure is described as fine lath martensite with a small amount of dispersed carbides. This is a classic structure for a low-to-medium carbon hardfacing alloy, and it represents a deliberate design choice to avoid the high hardness and high cracking sensitivity of a fully martensitic or carbide-rich deposit. The X-ray diffraction analysis confirms the presence of martensite and carbides, and the hardness is described as "not high" which I interpret as being in the range of 40–50 HRC, significantly lower than the 55–60 HRC typical of K360 base metal. The impact toughness is relatively high, and the abrasive wear resistance is comparable to the base metal.

Property Hardfacing Layer K360 Base Metal Practical Significance
Microstructure Fine lath martensite + dispersed carbides Tempered martensite Hardfacing layer has better toughness
Hardness Moderate (est. 40–50 HRC) High (55–60 HRC) Lower hardness reduces cracking risk
Impact Toughness Relatively high Moderate Better resistance to impact loading
Abrasive Wear Resistance Comparable to base metal Reference Acceptable for repair applications
Cold Cracking Tendency Low Moderate Easier to weld without preheat

Engineering Practice Insights and Lessons Learned

This paper is particularly valuable because it challenges the common assumption that a hardfacing layer must be harder than the base metal to provide adequate wear resistance. In my experience, this assumption is often wrong, especially for impact-abrasive wear conditions. A hardfacing layer that is too hard and too brittle will crack and spall under impact, and the spalled fragments become abrasive particles that accelerate wear on the underlying material. The fine lath martensite with dispersed carbides described in this paper provides a good balance of hardness and toughness, which is exactly what you want for a chute liner or a hopper wall that sees both abrasive and impact loading.

I have personally specified hardfacing alloys for coal preparation plant chutes, and I can tell you that the choice of filler wire is critical. A flux-cored wire that produces a deposit with 45–50 HRC and good toughness will outperform a harder deposit in most mining applications. The key is to ensure that the carbides are fine and dispersed, not coarse and continuous at the grain boundaries. The paper's finding that the wear resistance reaches the base metal level is a strong endorsement of this approach, and I would recommend this hardfacing alloy for any repair application where the base metal is a high-hardness martensitic steel.

One practical issue that the paper does not address but that I want to mention is the dilution effect. When you hardface a high-carbon steel like K360, the carbon from the base metal will diffuse into the deposit, increasing its hardness and cracking tendency. In my shop, we always used a buffer layer of a low-carbon austenitic stainless steel or a nickel-based alloy before applying the hardfacing layer. This is not mentioned in the paper, but it is essential for preventing dilution-related cracking.

Summary

This paper demonstrates that a hardfacing layer with fine lath martensite and dispersed carbides can achieve wear resistance comparable to K360 base metal while maintaining good toughness and low cracking tendency. The findings challenge the conventional wisdom that harder is always better for wear resistance, and they provide a practical basis for selecting hardfacing alloys for mining equipment repair. For engineers involved in hardfacing of high-hardness steels, this is a valuable reference that supports the use of moderate-hardness deposits with good toughness for impact-abrasive wear conditions.