Low-Frequency Magnetic Field Effect on Roll Submerged Arc Surfacing Microstructure and Properties
Why This Paper Matters on the Shop Floor
I have spent over three decades in the steel pipe and fitting industry, and I have seen more rolls scrapped prematurely than I care to count. When a roll fails on a forming mill or a pipe straightener, the entire line stops, and the cost is measured in tonnes of lost production, not just in the cost of the roll itself. This paper by Chang Yunlong and colleagues addresses a problem I have wrestled with personally: how do you get a hardfaced roll to hold up under repeated thermal and mechanical cycling without the surface spalling or cracking prematurely? The answer they propose, using a low-frequency pulsed longitudinal magnetic field during submerged arc surfacing, is not just an academic curiosity. It is a practical process modification that can be implemented on existing hardfacing equipment with relatively modest investment.
The authors set out to determine whether an externally applied magnetic field could influence the solidification of the weld metal in a way that improves grain structure and hardness. They used a roll substrate, applied a pulsed longitudinal magnetic field during the submerged arc welding process, and then characterized the resulting deposit. The key parameters they varied were the peak current (Ip), the base current (Ib), and the frequency (f) of the magnetic field. The results showed that at Ip=300A, Ib=200A, and f=5Hz, the grain size was refined to 30.1μm, and the hardness increased by 4.5HRC compared to a deposit made without the magnetic field.
Technical Parameters and Process Window
The following table summarizes the key parameters and results from the study.
| Parameter | Value / Range | Effect on Deposit |
|---|---|---|
| Magnetic field type | Pulsed longitudinal | Electromagnetic stirring of the weld pool |
| Peak current (Ip) | 300 A | Optimal for grain refinement in this study |
| Base current (Ib) | 200 A | Maintains arc stability while allowing stirring |
| Frequency (f) | 5 Hz | Optimal for the observed refinement |
| Grain size (with field) | 30.1 μm | Refined compared to no-field condition |
| Hardness increase | +4.5 HRC | Attributed to finer grains and denser carbide distribution |
| Mechanism | Arc rotation and pool stirring | Changes nucleation and growth kinetics |
From my experience, the ability to achieve a 30μm grain size in a hardfacing deposit is significant. In many roll hardfacing applications, especially those involving high chromium alloys, the grain structure can be coarse and columnar, which makes the deposit more susceptible to thermal fatigue cracking. The authors' finding that the magnetic field promotes a more equiaxed, refined structure is directly relevant to extending roll service life.
The Mechanism Behind the Improvement
The authors explain that the pulsed longitudinal magnetic field causes the arc to rotate, which in turn stirs the molten weld pool. This electromagnetic stirring has two primary effects. First, it breaks up the growing dendrites, creating more nucleation sites for new grains. Second, it distributes the heat more uniformly within the pool, reducing the temperature gradient and promoting a more equiaxed solidification mode. The result is a finer, more homogeneous grain structure with a corresponding increase in hardness.
I have seen the consequences of coarse, columnar grains in hardfaced rolls. When a roll is subjected to cyclic loading, the columnar boundaries act as preferential paths for crack propagation. A finer, equiaxed structure distributes the stress more evenly and resists crack initiation and growth. The 4.5HRC hardness improvement is also meaningful. In abrasive wear applications, a few points of hardness can translate into a significant increase in wear life, especially when the hard phase distribution is uniform.
Practical Implications for Roll Manufacturing and Repair
For a plant manager or a welding engineer, the immediate question is whether this process modification is feasible on existing equipment. The answer is yes, with some caveats. Applying a magnetic field requires either a set of coils around the workpiece or a specialized torch design that can generate the field at the point of welding. In my experience, retrofitting a hardfacing lathe with magnetic coils is not a trivial task, but it is well within the capability of a competent maintenance team. The power requirements are modest, and the control system can be integrated with the existing welding power source.
The frequency of 5Hz is particularly interesting. At low frequencies, the magnetic field has time to influence the pool during each cycle, but not so much time that the pool becomes unstable. This is a sweet spot that balances stirring effectiveness with process stability. I have seen attempts to use higher frequencies, and they often lead to arc instability and spatter, which are unacceptable in a production environment.
Lessons Learned and Reflections
One of the most important lessons I take from this paper is the importance of controlling solidification conditions in hardfacing. In many shops, the approach to roll hardfacing is still "set the parameters, run the weld, and hope for the best." This paper demonstrates that a relatively simple external influence can have a profound effect on the deposit quality. It also reinforces a principle I have preached for years: the properties of a weld deposit are determined as much by the cooling and solidification conditions as by the chemistry of the filler metal.
However, I would caution against over-reliance on a single set of optimal parameters. The authors found that the effect was most pronounced at Ip=300A, Ib=200A, and f=5Hz, but this was for a specific roll material and a specific set of welding conditions. In practice, the optimal parameters will vary with the roll diameter, the base material, the filler wire composition, and the heat input. A thorough process qualification is essential before implementing this technique on a production line.
Summary and Outlook
This study provides a clear demonstration that low-frequency pulsed longitudinal magnetic fields can significantly refine the grain structure and increase the hardness of submerged arc hardfacing deposits on rolls. The mechanism, electromagnetic stirring of the weld pool, is well understood and can be practically implemented with appropriate equipment. For the steel pipe industry, where rolls are critical to the forming and sizing of pipe, this technique offers a viable path to extending roll life and reducing downtime. The key is to qualify the process for the specific application and to monitor the deposit quality rigorously. I would recommend that any plant considering this approach start with a small-scale trial on a sacrificial roll, measure the grain size and hardness, and compare the results with a conventional deposit before committing to a full production change.
Zhuojin Pipe Fitting Co., Ltd