ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cobalt-Based Alloy TIG Surfacing Interface Structure and Properties

The Value of Cobalt-Based Alloys in High-Temperature Service

Cobalt-based alloys, such as Stellite, have been the material of choice for high-temperature, high-wear applications for decades. They are used in valve seats, hot working dies, turbine blades, and other components that must withstand a combination of high temperature, corrosion, and abrasive wear. The key to their performance is the combination of a tough cobalt-based matrix with hard carbide phases, which provides both strength and wear resistance at elevated temperatures. This paper by Li Guodong and colleagues investigates the interface structure and properties of a cobalt-based alloy deposited on X45CrSi9-3 steel using tungsten inert gas (TIG) welding.

The authors used TIG welding to deposit the cobalt-based alloy on the substrate and then subjected the samples to post-weld heat treatment at temperatures ranging from 500°C to 780°C. They measured the hardness of the deposit after each heat treatment and examined the microstructure using optical microscopy. The results show that the deposit achieves a good metallurgical bond with the substrate, with a clean interface and no porosity or cracking. The microstructure consists of a eutectic carbide phase, (Cr,Fe)7C3, and a γ(Co) matrix. The hardness increases with increasing heat treatment temperature, reaching a maximum at 750°C, and then decreases slightly at higher temperatures.

Key Findings and Their Practical Significance

The following table summarizes the key findings from the study.

Item Result / Finding
Substrate material X45CrSi9-3 steel
Surfacing method TIG welding (tungsten inert gas)
Deposit material Cobalt-based alloy
Interface quality Clean, no porosity or cracks, good metallurgical bond
Deposit microstructure Eutectic (Cr,Fe)7C3 + γ(Co) matrix
Heat treatment range 500°C to 780°C
Hardness trend Increases with temperature, peaks at 750°C, then decreases
Maximum hardness At 750°C heat treatment

The most significant finding is the effect of post-weld heat treatment on the hardness of the deposit. The hardness increases with increasing heat treatment temperature up to 750°C, which is a relatively high temperature for a cobalt-based alloy. This suggests that the heat treatment promotes the precipitation of additional hard phases or the coarsening of existing carbides, which increases the hardness. However, at temperatures above 750°C, the hardness decreases, likely due to the coarsening of the carbides or the softening of the matrix.

The Interface Structure and Its Importance

The interface between the cobalt-based alloy and the X45CrSi9-3 steel is critical to the performance of the component. The authors found that the interface is clean, with no porosity or cracks, and that a good metallurgical bond is achieved. This is a result of the TIG welding process, which provides a concentrated heat source that melts the substrate surface and allows the cobalt-based alloy to fuse with it.

In my experience, the quality of the interface is often the determining factor in the service life of a cobalt-based alloy component. If the interface is not properly bonded, the deposit can spall or delaminate under thermal cycling or mechanical loading. The authors' finding that the interface is clean and well-bonded is a positive indication that the TIG process can produce high-quality deposits.

However, the authors also note that the cobalt-based alloy does not undergo vigorous stirring in the weld pool. This means that the dilution of the substrate into the deposit is relatively low, which is beneficial for maintaining the properties of the cobalt-based alloy. At the same time, the lack of stirring means that the deposit may have a more columnar grain structure, which could affect its properties. The authors did not report the grain structure of the deposit, but this is an area that warrants further investigation.

Practical Considerations for Cobalt-Based Alloy Surfacing

For a plant that is considering the use of cobalt-based alloy surfacing, there are several practical considerations:

  1. Welding process selection: TIG welding is a good choice for cobalt-based alloys because it provides a clean, controlled heat input that minimizes dilution and produces a high-quality deposit. However, it is a relatively slow process, and for large components, other processes such as plasma transferred arc (PTA) welding may be more efficient.
  2. Post-weld heat treatment: The heat treatment temperature has a significant effect on the hardness of the deposit. The optimal temperature is around 750°C, but this should be verified for the specific alloy and application. In practice, the heat treatment is often combined with a stress-relief treatment for the substrate.
  3. Deposit quality: The deposit must be free of porosity, slag inclusions, and cracking. The TIG process, when properly controlled, can produce high-quality deposits, but the welding parameters must be carefully optimized.
  4. Substrate preparation: The substrate surface must be clean and free of any contamination before welding. In my experience, the most common cause of defects in cobalt-based alloy surfacing is poor surface preparation.

Lessons from the Field

I have seen cobalt-based alloy surfacing used in a variety of applications, including valve seats, hot work dies, and extrusion tools. In one application involving a hot work die for a pipe extrusion process, the die was surfaced with a cobalt-based alloy and then heat treated at 750°C. The die performed well, lasting more than twice as long as a conventional die made from tool steel. The heat treatment at 750°C was critical to achieving the desired hardness and wear resistance.

However, I have also seen cases where the heat treatment temperature was too high, resulting in a decrease in hardness and premature wear. The authors' finding that the hardness decreases above 750°C is a valuable reminder that the heat treatment must be carefully controlled to avoid over-tempering the deposit.

Summary and Outlook

This study provides a detailed characterization of the interface structure and properties of a cobalt-based alloy deposited on X45CrSi9-3 steel using TIG welding. The deposit achieves a good metallurgical bond with the substrate, with a clean interface and no porosity or cracking. The microstructure consists of a eutectic (Cr,Fe)7C3 phase and a γ(Co) matrix, and the hardness increases with increasing post-weld heat treatment temperature, reaching a maximum at 750°C. For practical applications, the TIG process is a reliable method for producing high-quality cobalt-based alloy deposits, but the post-weld heat treatment must be carefully controlled to achieve the optimal hardness and wear resistance. The key is to qualify the process for the specific application and to monitor the deposit quality rigorously. Cobalt-based alloy surfacing remains a valuable tool for extending the service life of components in high-temperature, high-wear applications, and this study provides useful guidance for its implementation.