Effect of TiC on Microstructure and Wear Resistance of High-Chromium Hardfacing Layers
Literature Overview and Core Findings
The paper by Lu et al. (2012) investigates the influence of TiC additions to a high-chromium hardfacing alloy deposited by flux-cored wire using the open-arc (self-shielded) process. The work is particularly relevant to the steel pipe and fitting industry because high-chromium hardfacing is commonly used to protect components such as pump casings, valve bodies, and pipe fittings that handle abrasive slurries.
The authors found that as TiC content in the flux-cored wire increases, the dilution effect from the Q235A substrate decreases, and the undesirable microstructural features—such as chromium-rich α-Fe solid solution and network or dendritic carbides—diminish and eventually disappear. This is a crucial finding because these microstructural features are associated with poor toughness and anisotropic properties in hardfacing layers.
Technical Interpretation and Process Parameters
The open-arc flux-cored wire process is widely used in the field because it requires no shielding gas, making it ideal for outdoor work and large components. However, it is also a process that is prone to high dilution, because the arc is more energetic and the deposition rate is higher than with shielded processes. The authors' finding that TiC reduces dilution is therefore of great practical importance.
The mechanism is likely twofold. First, TiC particles in the flux act as nucleation sites for the primary carbides, promoting a more uniform and refined microstructure. Second, the TiC may react with the substrate material, forming a barrier layer that limits the mixing of substrate and deposit. The result is a hardfacing layer that more closely retains the intended alloy composition.
The wear test results, conducted using the wet sand abrasion method, showed that a certain amount of TiC improves the wear resistance of the open-arc hardfacing alloy. The wear mechanism was identified as micro-spalling, which suggests that the hardfacing layer fails by the removal of small particles rather than by gross plastic deformation or cutting. This is characteristic of a hard, brittle microstructure where the matrix is unable to support the hard particles under high-stress abrasion.
Comparison of Microstructures and Properties
The following table summarizes the microstructural evolution and wear behavior as TiC content increases:
| TiC Content | Microstructure | Dilution Effect | Wear Mechanism | Wear Resistance |
|---|---|---|---|---|
| Low | Network/dendritic carbides, Cr-rich α-Fe | High | Micro-spalling | Moderate |
| Moderate | Refined carbides, less α-Fe | Moderate | Micro-spalling | Improved |
| High | Uniform fine carbides, minimal α-Fe | Low | Micro-spalling | Best |
The key insight is that TiC does not simply add hard particles; it changes the solidification behavior of the entire deposit. By promoting heterogeneous nucleation, it refines the microstructure and reduces the segregation of chromium, which is responsible for the brittle network carbides.
Engineering Practice and Lessons Learned
In my experience, high-chromium hardfacing alloys are notorious for their poor toughness and tendency to crack, especially when deposited in thick layers or on thick substrates. The addition of TiC appears to address this problem by refining the microstructure and reducing the formation of brittle phases.
However, I would caution against over-reliance on TiC as a universal solution. The paper used a specific base composition and a specific deposition process. In practice, the optimal TiC content will depend on the base alloy, the substrate, the deposition parameters, and the service conditions. A TiC addition that improves wear resistance in a wet sand test may not perform as well under high-stress abrasion or impact loading.
Another practical consideration is the cost and availability of TiC-containing flux-cored wires. TiC is a relatively expensive material, and the addition of TiC to a flux-cored wire may not be economically justified for all applications. The decision to use a TiC-containing wire should be based on a cost-benefit analysis that considers the expected increase in service life versus the additional cost of the wire.
Study Insights and Reflections
This paper is a good example of how a small addition of a reactive compound can have a disproportionate effect on the properties of a hardfacing layer. The authors did not simply add TiC as a hard particle; they used it as a metallurgical tool to control solidification and reduce dilution. This is a sophisticated approach that shows a deep understanding of the underlying metallurgy.
From a practical standpoint, the most valuable contribution of this work is the demonstration that the open-arc process can be used to produce high-quality hardfacing layers, provided the alloy system is properly designed. This is important because the open-arc process is often dismissed as a low-quality process, suitable only for non-critical applications. This paper shows that with the right alloy design, it can produce deposits with excellent wear resistance.
One gap in the study is the lack of data on the impact toughness of the hardfacing layers. While wear resistance is important, many components also experience impact loading, and a hardfacing layer that is too brittle will fail by chipping or spalling. Future work should include impact tests to ensure that the TiC-containing hardfacing layers can withstand both abrasive and impact loading.
Conclusion and Outlook
The addition of TiC to high-chromium hardfacing alloys deposited by open-arc flux-cored wire offers a practical route to improving wear resistance while reducing dilution and microstructural anisotropy. The mechanism is primarily microstructural refinement and the suppression of brittle network carbides. This work has direct relevance to the hardfacing of components in the steel pipe and fitting industry, particularly those handling abrasive slurries. However, the economic viability and performance under impact loading need to be evaluated before the approach can be recommended for widespread industrial adoption. The next logical step is to conduct field trials on actual components in service to validate the laboratory findings under real-world conditions.
Zhuojin Pipe Fitting Co., Ltd