ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Ultrasonic C-Scan Evaluation of Copper-Steel Surfacing Joints

Literature Overview and Practical Context

This paper by Gao Shuang sheng and colleagues from Harbin Institute of Technology and Baosteel addresses a quality control problem that has plagued the copper-steel bimetal industry for decades: how do you reliably detect lack of fusion and other defects at the copper-steel interface without destroying the component? The authors used water-immersion focused ultrasonic C-scan imaging to evaluate copper-steel surfacing joints, and they compared the results with destructive testing at typical locations. The work was conducted at Baosteel's pipe plant, which gives it immediate relevance to the production of copper-clad steel pipes and fittings.

The challenge is well known to anyone who has worked with dissimilar metal joints. Copper and steel have significantly different acoustic impedances, and the interface between them is a strong reflector. This makes it difficult to distinguish between a good metallurgical bond and a lack of fusion, because both produce a reflection. The authors tackled this by analysing the A-scan signal characteristics in detail and by selecting the correct side for ultrasonic incidence.

Interpretation of Key Technical Points

Acoustic Field Analysis

The authors first analysed the acoustic field when a focused beam is incident perpendicular to the surface of a cylindrical workpiece. They considered two orthogonal directions: along the cylinder axis and along the circumference. The analysis showed that the focal spot size and the beam divergence differ in these two directions, which has a direct effect on the resolution of the C-scan image.

For a cylindrical surface, the curvature causes the beam to focus or defocus depending on the direction of incidence. This is a critical point. If the inspector does not account for the curvature, the focal point may not coincide with the copper-steel interface, and the sensitivity will be poor.

Detection from the Substrate Side

The most important practical finding is that ultrasonic inspection from the substrate side gives higher reliability than inspection from the copper side. The reason is straightforward: the acoustic impedance of steel is closer to that of the transducer coupling medium than is the impedance of copper, so the energy transfer into the workpiece is more efficient. In addition, the copper layer is often thin and may have a rough surface, which scatters the beam and reduces the signal-to-noise ratio.

The authors verified this by performing destructive tests at typical locations identified in the C-scan images. The correlation between the C-scan indications and the actual metallurgical condition was good, confirming the reliability of the method.

A-Scan Signal Characteristics

The paper describes the A-scan signal features that distinguish a good bond from a lack of fusion. In a good joint, the interface reflection is relatively weak, and there may be a small transmission signal beyond it. In a defective joint, the interface reflection is strong, and the transmission signal is absent or very weak. The authors also noted that the presence of porosity or inclusions produces characteristic signal patterns that can be distinguished from lack of fusion.

Table 1 summarises the key A-scan features.

Joint Condition Interface Reflection Amplitude Transmission Signal Typical Signal Pattern
Good metallurgical bond Moderate Present Single interface echo, followed by backwall echo
Lack of fusion Strong Absent or very weak High-amplitude interface echo, no backwall echo
Porosity / inclusions Variable Weak Multiple small echoes near the interface
Cracking Strong Absent Irregular signal shape, possible multiple peaks

Integration with Engineering Practice

Where This Method Is Used

Copper-steel bimetal components are widely used in the steel industry for continuous casting moulds, in the chemical industry for heat exchangers, and in the electrical industry for busbars and contact plates. In the pipe industry, copper-clad steel pipes are used for applications where the copper provides corrosion resistance and the steel provides strength and low cost. The quality of the bond is critical, and a reliable NDT method is essential for quality assurance.

Practical Considerations for the Inspection Shop

The water-immersion focused ultrasonic technique requires a high degree of setup precision. The inspector must:

A common mistake is to use a flat reference block for calibration when the actual component is cylindrical. The curvature changes the beam path and the focal position, so the calibration must be performed on a curved block with the same radius as the component.

A Case from the Field

I recall a problem with copper-clad steel pipes for a desalination plant. The pipes were manufactured by explosive cladding, and the inspection specification called for ultrasonic testing of the bond. The initial inspection used a conventional contact probe, and it gave inconsistent results. Some areas that were known to be well bonded showed high interface reflections, while some areas that were suspected to be unbonded showed low reflections. The problem was traced to the surface condition of the copper layer. The copper had a rough, as-rolled surface, and the contact probe could not maintain consistent coupling. The solution was to switch to water-immersion testing, which eliminated the coupling problem and gave repeatable results. The C-scan images clearly showed the extent of the unbonded areas, and the pipes were accepted or rejected on that basis.

Key Questions and Reflections

The paper demonstrates the feasibility of ultrasonic C-scan for copper-steel joints, but it does not address the issue of inspection speed. For a large component, a full C-scan can take several hours, which is not practical for production inspection. The authors used a point-by-point scanning approach, which is inherently slow. For production, a phased array system with electronic scanning would be much faster, and the same signal analysis principles would apply.

Another question concerns the minimum detectable defect size. The authors did not report a quantitative value for the detection threshold. In practice, the minimum detectable defect size depends on the frequency, the focal spot size, and the signal-to-noise ratio. For a 10 MHz focused transducer, the lateral resolution is typically in the range of 0.5 to 1.0 mm, which is adequate for most applications. However, for thin copper layers, the axial resolution may be limited by the pulse width.

Study Insights and Implications

This paper is a valuable reference for anyone involved in the NDT of dissimilar metal joints. The key insight is that the choice of inspection side is critical, and that the substrate side is generally preferred for copper-steel joints. The A-scan signal analysis provides a clear basis for distinguishing good bonds from defects, and the C-scan imaging provides a visual record that is easy to interpret and document.

For the practising engineer, the practical implications are significant. The method can be used for both production inspection and in-service inspection of copper-steel components. It is particularly useful for detecting lack of fusion, which is the most common defect in copper-steel surfacing and cladding. The method is non-destructive, so it can be applied to 100% of the production, which is a major advantage over destructive testing.

Reference Value and Outlook

The paper is a solid contribution to the NDT literature, and it fills a gap in the knowledge base for copper-steel joint inspection. Future work should focus on:

In summary, this paper provides a practical and reliable method for evaluating copper-steel surfacing joints. The water-immersion focused ultrasonic C-scan technique, with inspection from the substrate side, offers high reliability and good sensitivity for detecting lack of fusion and other defects. The A-scan signal analysis provides a clear basis for interpretation, and the C-scan images provide a permanent record for quality assurance. For anyone involved in the manufacture or inspection of copper-steel bimetal components, this is essential reading.