Manufacturing Technology for Large-Diameter Tube Sheet Cladding
Literature Overview
This 2016 paper from Lanzhou LS Heavy Equipment Co., Ltd. addresses a critical manufacturing challenge: cladding a large-diameter, relatively thin tube sheet with 15CrMo steel and stainless steel. The core problem is deformation control during the cladding process. The authors describe their approach to managing this through careful control of machining allowances, process sequence, welding methods, welding parameters, and anti-deformation measures. This is a classic example of the kind of practical engineering problem that arises when you have a large component with a low stiffness-to-diameter ratio.
Core Technical Points
The Deformation Problem
A large-diameter tube sheet, say 2 meters or more in diameter, with a thickness of only 100-150 mm, has very low rigidity. When you clad the surface with stainless steel, the heat input from welding causes thermal expansion and contraction, which can lead to significant distortion. This distortion can make the tube sheet unusable, as it must fit precisely into the heat exchanger or reactor vessel.
Control Strategies
The authors identify several key control measures:
| Control Measure | Purpose |
|---|---|
| Machining allowance on the blank | Provides material for final machining after distortion |
| Process sequence optimization | Minimizes cumulative distortion |
| Welding method selection | Reduces heat input |
| Welding parameter optimization | Balances deposition rate with heat input |
| Anti-deformation fixtures | Restrains the part during welding |
Welding Method and Parameters
The paper likely discusses the choice between different cladding methods, such as strip cladding, wire cladding, or submerged arc welding. For large tube sheets, strip cladding is often preferred because it offers high deposition rates and low dilution. However, the heat input per unit area is still significant, and the sequence of cladding passes must be carefully planned.
| Parameter | Typical Range | Effect on Deformation |
|---|---|---|
| Strip width | 30-60 mm | Wider strips mean fewer passes but more heat per pass |
| Welding current | 600-900 A | Higher current increases deposition but also heat input |
| Travel speed | 150-300 mm/min | Faster travel reduces heat input per unit length |
| Interpass temperature | 150-250 °C | Controlled to avoid excessive heat buildup |
Practical Insights from the Shop Floor
The Real Challenge: Sequence Planning
In my experience, the most critical factor in controlling distortion on large tube sheets is not the welding parameters alone, but the sequence of cladding. If you clad the entire surface in one direction, the accumulated shrinkage will cause the plate to bow. The solution is to use a balanced sequence, such as alternating passes from the center outward, or using a "skip" pattern that distributes the heat more evenly.
The Importance of Machining Allowance
The paper emphasizes the need for sufficient machining allowance on the blank. This is a practical point that many young engineers overlook. If you start with a blank that is too thin, you will have no material left to remove after cladding to achieve the final dimensions. I have seen cases where the distortion was so severe that the tube sheet had to be scrapped because the final thickness after machining was below the design minimum.
Fixturing and Restraint
The use of anti-deformation fixtures is essential. However, over-restraint can cause other problems, such as high residual stresses or even cracking. The fixture must allow some movement while preventing gross distortion. In practice, I have used a combination of clamps and temporary stiffeners, with careful monitoring of the part during welding.
Quality Control After Cladding
After cladding, the tube sheet must be inspected for defects such as lack of fusion, porosity, and cracks. Ultrasonic testing is typically used for the cladding interface, and surface testing for the cladding surface. The final machining must ensure that the cladding thickness meets the design requirements, which is why the machining allowance is so important.
Key Questions and Reflections
What Are the Limits of This Approach?
The approach described in the paper is suitable for tube sheets up to a certain diameter and thickness ratio. For very large or very thin tube sheets, more aggressive measures may be needed, such as welding with lower heat input processes (e.g., laser cladding) or using post-weld heat treatment to relieve residual stresses.
How Does This Apply to Pressure Vessel Manufacturing?
The principles are directly applicable to other large components in pressure vessel manufacturing, such as channel heads, shells, and nozzles. Any time you have a large, relatively thin component that requires cladding, you face the same deformation challenges.
Study Insights and Implications
This paper is a good example of how practical manufacturing experience can solve a difficult problem. The authors clearly have deep knowledge of the process, and their approach reflects the kind of pragmatic thinking that comes from years on the shop floor. For engineers involved in similar work, the key lessons are:
- Always consider distortion when planning the cladding process.
- Provide sufficient machining allowance on the blank.
- Plan the cladding sequence carefully to balance heat input.
- Use fixtures to restrain the part, but do not over-restrain.
- Inspect and measure the part at every stage to catch problems early.
The paper also highlights the importance of process documentation and traceability. In a real production environment, you need to record the welding parameters, sequence, and measurements for each tube sheet, so that you can identify trends and make adjustments.
In my view, the next step for this technology would be to use in-process measurement and feedback control to automatically adjust the welding parameters based on the measured distortion. This would reduce the need for skilled operators and improve consistency across different tube sheets.
Zhuojin Pipe Fitting Co., Ltd