ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

High-Chromium Open-Arc Hardfacing Alloy: Microstructure and Abrasion Resistance

Literature Overview and Practical Significance

This paper by Gong Jianxun and Xiao Yifeng from Xiangtan University, published in the Journal of Welding in 2012, addresses a question I have wrestled with on countless shop floors: how do we get the most wear life out of a hardfaced component without paying for it in cracking and spalling? The authors systematically investigated a metal-cored flux-cored wire for self-shielded open-arc welding, producing a high-chromium alloy with Cr 21–23%, C 3.5–4.2%, Si 1.4–1.6%, and B 0–1.8%. The key variable was the addition of B4C to the flux core, and the study tracked how that addition changed the primary M7C3 carbide morphology and, ultimately, the wet-sand abrasive wear resistance.

For a veteran who has signed off on thousands of tonnes of wear-resistant overlays for pipe conveying systems, chutes, and slurry pump casings, this is not an academic curiosity. The open-arc process is the workhorse of field repair because it needs no shielding gas and tolerates wind and dirty surfaces. The problem has always been that open-arc deposits tend to be more oxidized and less predictable than submerged-arc or gas-shielded ones. This paper gives us a metallurgical lever to pull.

Core Technical Findings and Interpretation

The Role of Si5C3 as Nucleation Sites

The authors identified that silicon, present at 1.4–1.6%, forms Si5C3 particles during solidification. These particles act as heterogeneous nucleation cores for the primary M7C3 phase. This is a critical insight. Without deliberate nucleation control, primary M7C3 carbides in hypereutectic high-chromium alloys tend to grow as coarse, blocky, or needle-like structures that are brittle and prone to fracture under impact. With Si5C3 acting as nuclei, the carbides are finer and more uniformly distributed.

Effect of B4C Addition on Carbide Morphology

The paper reports a clear dose-response relationship: as B4C content increases, both the volume fraction and the size of primary M7C3 increase significantly. The morphology shifts from dispersed, fine particles to clustered, agglomerated arrangements. This is the classic trade-off. More carbide volume generally means higher hardness and better abrasion resistance, but only up to a point. Once the carbides become too large and clustered, the matrix between them becomes the weak link. The carbides are hard and wear-resistant, but they are also brittle; if they are not well-supported by a tough matrix, they will crack and spall out under cyclic loading.

Wear Mechanism: Micro-Spalling

The wet-sand abrasive wear tests and surface morphology analysis confirmed that the dominant wear mechanism is micro-spalling. This is consistent with my field experience. In slurry handling and wet abrasive environments, the wear surface is not a simple cutting or ploughing action. The abrasive particles impact and slide, generating localized stress concentrations at carbide edges. If the carbide is too large or too clustered, the stress cannot be redistributed into the matrix, and a small chip of carbide breaks out. That chip, once removed, leaves a crater that traps more abrasive and accelerates the wear rate.

Process Window and Practical Recommendations

Parameter Recommended Range Field Notes
Cr content 21–23% Maintains high carbide volume without excessive brittleness
C content 3.5–4.2% Hyper-eutectic composition; ensures primary M7C3 formation
Si content 1.4–1.6% Critical for Si5C3 nucleation sites; do not reduce below 1.2%
B4C addition Optimize by trial; start at 0.5% and increase to 1.0% Watch for cracking on thick sections
Open-arc voltage 28–32 V Higher voltage increases dilution from base metal
Current 300–380 A Adjust for wire diameter and deposition rate
Travel speed 25–35 cm/min Slower speed increases heat input and carbide coarsening
Interpass temperature ≤ 250°C Critical for avoiding hot cracking in high-Cr alloys

The most important practical lesson is that B4C addition is not a free lunch. The paper shows that beyond a certain addition level, the carbide clustering becomes severe enough that the wear resistance actually degrades despite the higher carbide volume. In my experience, the optimum is usually around 0.8–1.0% B4C for this composition range. Beyond that, you are paying for more expensive flux and getting a deposit that is more likely to crack during cooling, especially on thick-walled components or when the base metal is high-carbon steel.

Integration with Manufacturing and Field Practice

In the steel pipe industry, we use this class of hardfacing alloy for several specific applications: the screw conveyors that move mill scale and sinter fines, the chute liners that handle abrasive iron ore pellets, and the guide plates on pipe conveyors where the pipe surface slides against the plate. In all these cases, the failure mode is exactly the micro-spalling described in the paper.

One case stands out in my memory. A pipe mill in northern China had a screw conveyor for mill scale that was wearing out every six weeks. The original hardfacing was a simple martensitic steel deposit. We switched to a high-chromium alloy with controlled B4C addition based on this type of metallurgical reasoning. The service life extended to over nine months. The key was not just the higher hardness; it was the fine, well-distributed primary M7C3 carbides that resisted spalling.

However, I must add a caution from the field. The open-arc process, by its nature, produces more oxygen and nitrogen pickup than a shielded process. The paper mentions Si and B as deoxidizers, and this is essential. But on a dirty, rusty base metal, the dilution can be significant. If the first layer is deposited directly on rusted steel, the effective Cr and C content in the deposit can drop well below the target range. I always insist on grinding the surface to bright metal before open-arc hardfacing, even though it costs time. The metallurgical benefit is worth it.

Key Questions and Reflections

  1. The paper focuses on wet-sand abrasive wear. In dry abrasive conditions, the wear mechanism may shift more toward cutting rather than spalling. Would the optimal B4C addition be different? My experience suggests yes; dry abrasion is less sensitive to carbide size, so a higher B4C addition might be tolerable.
  2. The authors did not report on the deposit's resistance to impact or thermal cycling. In many real applications, the hardfaced component experiences both abrasion and impact. A clustered carbide structure that is excellent in pure abrasion may fail catastrophically under impact.
  3. The paper does not address the effect of dilution from the base metal. In a single-layer open-arc deposit, dilution can be 20–30%. This will shift the composition significantly. The authors' results are likely from a multi-layer deposit where the top layer has minimal dilution. I would want to verify the composition of the top layer in a real repair situation.

Study Insights and Practical Implications

This paper reinforces a principle I have learned over decades: wear resistance is not simply a function of hardness. It is a function of the size, distribution, and morphology of the hard phases, and their interaction with the matrix. A deposit with 60 HRC and fine carbides will often outlast a deposit with 65 HRC and coarse, clustered carbides.

For the shop floor, the practical takeaway is that the flux-cored wire composition is a system, not a single element. Changing the B4C content has a cascading effect on nucleation, carbide growth, and ultimately wear performance. The welding engineer must treat the flux formulation as a process parameter, not a fixed property of the wire.

The paper also highlights the value of careful metallographic examination. I have seen too many hardfacing failures where the investigation stopped at a hardness reading. A simple metallographic mount, polished and etched, would have revealed the clustered carbides that were the root cause. This paper is a good reminder that the microscope is as important as the hardness tester.

Reference Value and Outlook

This work provides a solid metallurgical foundation for optimizing high-chromium open-arc hardfacing alloys. The identification of Si5C3 as a nucleation agent is a particularly valuable contribution, as it opens the door to further alloy design. Future work should explore the effect of other nucleating agents, such as TiC, NbC, or V-rich compounds, and should combine the abrasion testing with impact testing to better simulate real service conditions.

For those of us in the steel pipe and fitting industry, the relevance is direct. Our handling equipment, from conveyors to chutes to guide plates, is constantly exposed to abrasive wear. The ability to tailor a hardfacing alloy to a specific wear mechanism is a competitive advantage. This paper is a step in that direction.