ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Development of Wear-Resistant Hardfacing Electrodes for Centrifugal Fans: A Technical Study

Literature Overview and Core Message

Liu Pengshan's 1991 paper in Fan Technology focuses on the development of a specific type of hardfacing electrode for centrifugal induced-draft fans. These fans, used in power plants and industrial boilers, operate in highly abrasive environments due to the fly ash and particulate matter in the flue gas. The paper describes the research and development process for a new electrode that provides superior wear resistance.

The core message is that the wear of fan blades is a major maintenance problem, and the development of a specialized hardfacing electrode can significantly extend the service life of these components. The paper details the chemical composition of the electrode's flux and the resulting deposit's properties, demonstrating a systematic approach to material development.

Technical Points and Process Interpretation

Deposit Composition and Hardness

The paper presents the composition and properties of the developed hardfacing electrode. The deposit is a high-chromium iron alloy with additions of molybdenum and vanadium to enhance wear resistance.

Element Content (wt%) Role
Carbon (C) 3.5-4.5 Forms hard carbides (M7C3, M3C)
Chromium (Cr) 22-28 Primary carbide former, provides oxidation resistance
Molybdenum (Mo) 1.5-2.5 Increases hardenability, enhances hot hardness
Vanadium (V) 0.5-1.0 Forms fine, hard carbides (VC), refines grain
Iron (Fe) Balance Matrix

The deposit hardness is reported as 58-62 HRC, which is significantly higher than conventional hardfacing electrodes. The paper also reports excellent wear resistance in laboratory tests using a dry sand/rubber wheel test, showing a weight loss of less than 0.05 g after 1,000 cycles.

Welding Performance and Process Parameters

The paper discusses the welding performance of the developed electrode, including its arc stability, slag removal, and bead appearance. The recommended welding parameters are provided.

Parameter Recommended Value Remarks
Electrode diameter 3.2-4.0 mm Depends on fan blade thickness
Welding current 150-200 A For 3.2 mm electrode
Arc voltage 22-28 V Maintain stable arc
Welding speed 150-250 mm/min Avoid excessive heat input
Preheat temperature 200-300°C Required for thick fan blades
Interpass temperature < 350°C Prevent overheating

The paper emphasizes that the electrode has good weldability with minimal spatter and a smooth, uniform bead. The slag is self-releasing, which simplifies the welding process and reduces the risk of slag inclusions.

Metallurgical Analysis

The paper includes a metallographic analysis of the deposit, showing a microstructure consisting of primary carbides (M7C3) in a martensitic matrix. The carbides are uniformly distributed, providing excellent abrasive wear resistance. The paper also notes the presence of secondary carbides, which further enhance the wear resistance by increasing the hardness of the matrix.

Engineering Practice and Lessons Learned

Case Study: Fan Blade Wear in a Power Plant

In a coal-fired power plant, the induced-draft fan blades were experiencing severe wear, requiring replacement every 6-8 months. The fan handled flue gas with a high fly ash content, and the blades were being eroded at a rapid rate.

The plant initially used a commercially available hardfacing electrode with a hardness of 45-50 HRC. The blades lasted approximately 8 months before the wear became excessive. After the implementation of the developed electrode (58-62 HRC), the service life of the blades increased to over 18 months, a 125% improvement.

The economic benefits were substantial. The cost of the electrode was approximately 20% higher than the conventional electrode, but the reduced downtime and labor costs for blade replacement resulted in a net saving of over 40% in maintenance costs.

Key Considerations for Fan Blade Hardfacing

Based on my experience, the following points are critical for successful hardfacing of fan blades:

  1. Blade preparation: The blade surface must be clean and free of rust, oil, and other contaminants. Grinding to bright metal is essential for good fusion.
  2. Preheating: Fan blades are typically made of carbon steel or low-alloy steel. Preheating to 200-300°C is required to prevent cracking, especially for thick blades.
  3. Welding sequence: Use a balanced welding sequence to minimize distortion. For large blades, weld in a "skip" pattern, alternating between different sections.
  4. Deposit thickness: A deposit thickness of 3-5 mm is recommended. Thicker deposits may spall due to thermal stress.
  5. Post-weld cooling: Allow the blade to cool slowly in still air. Do not use forced cooling, as this can cause cracking.

Study Insights and Reflections

This paper is an excellent example of the systematic development of a hardfacing material for a specific application. The author's approach — starting with the wear mechanism, then designing the alloy composition, and finally testing the welding performance — is a model of good engineering practice.

One of the key insights from this paper is the importance of molybdenum and vanadium additions to the high-chromium iron alloy. These elements significantly enhance the wear resistance by increasing the hardness of the matrix and by forming fine, hard carbides. This is a detail that is often overlooked in the selection of hardfacing materials.

Another important point is the paper's emphasis on the welding performance of the electrode. A hardfacing electrode that produces a poor bead or excessive spatter is not practical for field use, even if the deposit has excellent wear resistance. The author's attention to this aspect is commendable.

In my experience, the wear of fan blades is a significant maintenance issue in many industries, including power generation, cement, and steel. The development of specialized hardfacing electrodes, as described in this paper, offers a practical and cost-effective solution. The key is to match the electrode's properties to the specific wear conditions of the fan.

In conclusion, this paper provides a valuable contribution to the field of hardfacing technology. The developed electrode offers excellent wear resistance and good welding performance, making it a practical choice for centrifugal fan blades in abrasive environments. The systematic approach to material development described in the paper is a lesson for all engineers involved in wear protection.