Hardfacing Materials and Process for Coal Crushing Rings: A Practical Study
Core Technical Content
The 2003 paper by Pei Haixu, Wang Sheng, and Fan Ling from the China North Industries Group Corporation's 52nd Research Institute addresses a critical problem in the coal processing industry: the rapid wear of crushing rings used in coal crushers. The paper presents a systematic approach to failure analysis, alloy design, and process development for hardfacing these components. The authors begin by conducting a failure analysis of the crushing rings to identify the wear mechanisms and the factors limiting their service life, then develop an optimal wear-resistant material composition and hardfacing process.
The paper identifies the primary wear mechanism as a combination of abrasive wear and impact fatigue, caused by the interaction between the crushing rings and the coal being processed. The authors compare several hardfacing alloy systems, including iron-based alloys with chromium, molybdenum, and vanadium additions, and evaluate their performance using laboratory wear tests. The key finding is that the optimal alloy composition must provide a high volume fraction of hard carbides within a tough martensitic matrix, which combines high hardness with sufficient toughness to resist impact and fatigue.
Practical Insights from the Shop Floor
In my experience with coal processing equipment, the crushing ring is a classic example of a component where the wear mechanism is complex and the service conditions are severe. The paper correctly emphasizes the importance of conducting a thorough failure analysis before selecting a hardfacing alloy, but it does not fully address the practical challenges of applying hardfacing to large, heavy crushing rings that are difficult to weld due to their size and material composition.
I have seen many crushing rings fail because the hardfacing was applied with insufficient preheating, resulting in cracking and spalling of the hardfacing layer during service. The practical solution that I have found most effective is to preheat the crushing ring to a temperature of 250 to 300 degrees Celsius before hardfacing and to maintain the interpass temperature at a similar level throughout the welding process. This approach minimizes the risk of hydrogen-induced cracking and ensures that the hardfacing deposit develops its full hardness without the risk of thermal stress cracking.
Lessons from Field Failures and Standards Integration
The paper's discussion of the relationship between alloy composition and wear resistance is particularly relevant to my experience with the repair and refurbishment of worn crushing rings. I recall a project where a coal processing plant was experiencing crushing ring life of only 500 hours, resulting in significant downtime and replacement costs. After analyzing the wear patterns and the coal characteristics, we determined that the original hardfacing alloy was too hard and brittle, leading to chipping and premature failure.
The solution was to switch to a more ductile iron-based alloy with a hardness of 55 to 60 HRC, which provided a better balance of wear resistance and toughness. This change extended crushing ring life to over 2000 hours, a four-fold improvement. The literature does not provide specific guidance on this alloy selection, but it does emphasize the importance of understanding the wear mechanism and selecting the alloy accordingly. My recommendation to fellow engineers is to conduct a thorough wear analysis before selecting a hardfacing alloy, including examination of the worn surface with scanning electron microscopy to identify the dominant wear mechanism.
The integration of this literature with modern standards such as ASTM G65 for abrasive wear testing and ISO 15156 for materials in sour service reveals that the industry lacks a standardized test method for evaluating the performance of hardfaced crushing rings under the specific conditions encountered in coal processing. My practical approach has been to develop a field trial protocol that involves installing test crushing rings on a representative crusher and measuring wear after a specified number of operating hours. This approach provides the most reliable data for making alloy selection decisions.
Summary and Reflection
The 2003 paper on hardfacing materials and process for coal crushing rings provides a comprehensive approach to solving a critical wear problem in the coal processing industry. Its emphasis on conducting a thorough failure analysis before selecting a hardfacing alloy is a fundamental principle that I have applied successfully in numerous projects. The practical lessons about preheating, interpass temperature control, and balancing hardness with toughness are essential for anyone involved in the hardfacing of heavy mining equipment. For the practicing engineer, the key takeaway is that wear-resistant hardfacing for coal crushing rings requires a comprehensive understanding of the wear mechanisms and a systematic approach to alloy design and process control. The cost of a failed crushing ring is not just the cost of replacement but also the cost of lost production, which can be many times greater.
Zhuojin Pipe Fitting Co., Ltd