ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Carbon Dilution in Austenitic Stainless Steel Cladding on Hualong One Containment Vessel

1. A Quality Problem That Stopped Production

This paper addresses a problem that every pressure vessel fabricator fears: a repeated failure in a critical quality test that threatens the delivery schedule. The "Hualong One" containment vessel's shell and head require an austenitic stainless steel cladding on the internal surface to provide corrosion resistance. The cladding is applied by weld overlay, and the chemical composition of the cladding layer must meet strict requirements. The carbon content is particularly critical, as high carbon in austenitic stainless steel can lead to sensitisation and intergranular corrosion.

The authors report that the carbon content in the cladding layer repeatedly failed to meet the specification. The customer's attention was drawn to the problem, and the fabricator had to investigate the root cause. This is a classic quality problem that requires a systematic approach, not a quick fix.

2. The Dilution Problem in Weld Cladding

Weld cladding involves depositing a corrosion-resistant alloy onto a carbon steel or low-alloy steel substrate. The first layer of cladding always contains some dilution from the base metal, as the welding arc melts a portion of the substrate and mixes it with the filler metal. This dilution is unavoidable, but it must be controlled to ensure that the cladding layer meets the required chemistry.

In this case, the base metal is a low-alloy steel with a carbon content of around 0.20%, while the cladding alloy is an austenitic stainless steel with a carbon content of around 0.03% or less. Even a small amount of dilution can increase the carbon content of the cladding layer above the specified limit. The authors investigated the factors that affect dilution:

3. Root Cause Analysis

The authors conducted a systematic investigation using a PDCA approach. They first verified the sampling method, as improper sampling can give misleading results. They then analysed the welding consumables and the base metal chemistry. Finally, they varied the welding parameters and the bead overlap to see the effect on the cladding layer's carbon content.

The results were clear: the filler wire's original carbon content and the bead overlap had a significant effect on the carbon content of the cladding layer. Other factors, such as welding current and travel speed, had a negligible effect.

Factor Effect on C Content in Cladding Significance
Filler wire C content Direct, proportional High
Bead overlap Inverse, proportional High
Welding current Minimal Low
Travel speed Minimal Low
Sampling method Verification required Medium

The filler wire's carbon content is the starting point. If the wire has a carbon content of 0.03%, and the base metal has 0.20%, then a dilution of 10% will result in a cladding carbon content of approximately 0.047%, which may exceed the specification. The bead overlap is also critical because it determines the amount of base metal melted and mixed into the cladding layer. A larger overlap means more dilution, while a smaller overlap means less dilution but a higher risk of lack of fusion.

4. Corrective Actions

The authors recommended two corrective actions:

  1. Use a filler wire with a lower carbon content. If the specification allows, a wire with a carbon content of 0.02% or less should be used. This gives more margin for dilution.
  2. Control the bead overlap precisely. The overlap should be set to a value that minimises dilution while ensuring complete fusion. This requires careful control of the welding torch position and travel speed.

The authors also noted that the sampling method must be verified. If the sample is taken from a location that includes a higher proportion of dilution, the result will be misleading. The sample should be taken from the cladding layer's surface, not from the interface with the base metal.

5. Lessons for the Shop Floor

This paper is a valuable case study in quality control. The key lessons are:

6. Closing Thoughts

This paper is a reminder that quality problems in weld cladding are rarely caused by a single factor. They are usually the result of a combination of factors, and the root cause can be found by systematic investigation. The authors' approach is a model of good engineering practice: identify the problem, analyse the factors, verify the root cause, and implement corrective actions. I would recommend this paper to any engineer involved in weld cladding, as it demonstrates the importance of understanding the metallurgy behind the process.