Technical Study Note: Turning of Stellite Alloy Surfacing Components
1. Literature Overview and Core Content
This 2005 paper from Dongfang Turbine Factory addresses the machining challenges of Stellite alloy surfacing components. The authors analyze the cutting performance of Stellite alloys and propose efficient machining methods for both rough and finish turning. They discuss tool selection, cutting parameters, and compare the cutting performance of different tool materials.
Stellite alloys are cobalt-based hard-facing alloys containing significant amounts of chromium, tungsten, and carbon. They are used extensively in turbine components, valves, and other high-temperature, high-wear applications. The paper focuses on the practical aspects of machining these hard, abrasive alloys, which are notoriously difficult to cut.
2. Technical Points and Process Analysis
2.1 Stellite Alloy Properties
Stellite alloys are characterized by their high hardness, excellent wear resistance, and good high-temperature strength. These properties are achieved through a solid-solution-strengthened cobalt matrix with hard carbide precipitates.
| Alloy | Composition (wt%) | Hardness (HRC) | Application |
|---|---|---|---|
| Stellite 6 | Co-28Cr-4W-1.2C | 38–42 | Valve seats, turbine blades |
| Stellite 12 | Co-29Cr-8W-1.8C | 44–48 | Severe wear, hot work tools |
| Stellite 21 | Co-27Cr-5Mo-0.25C | 30–35 | Impact and thermal shock resistance |
The high hardness and the presence of hard carbide particles make Stellite alloys difficult to machine. The carbides cause abrasive wear on cutting tools, while the cobalt matrix work-hardens during cutting, increasing the cutting forces.
2.2 Tool Selection
The paper discusses the selection of cutting tool materials for Stellite machining. The key requirement is high hot hardness and good wear resistance.
| Tool Material | Hardness (HV) | Max. Cutting Speed (m/min) | Suitability |
|---|---|---|---|
| HSS (high-speed steel) | 800–900 | 10–20 | Limited, only for light cuts |
| Carbide (K-type) | 1500–1800 | 30–60 | Good for roughing |
| Carbide (P-type) | 1600–1900 | 40–80 | Better for finishing |
| Ceramic (Al2O3-based) | 1800–2200 | 80–150 | Excellent for finishing |
| CBN (cubic boron nitride) | 4000–5000 | 150–250 | Best for finish machining |
The paper recommends carbide tools for roughing and ceramic or CBN tools for finishing. The choice depends on the desired surface finish and the machining allowance.
2.3 Cutting Parameters
The cutting parameters are critical for successful machining of Stellite alloys. The paper proposes the following parameters:
| Operation | Cutting Speed (m/min) | Feed Rate (mm/rev) | Depth of Cut (mm) |
|---|---|---|---|
| Roughing (carbide) | 30–50 | 0.3–0.5 | 2–4 |
| Roughing (ceramic) | 80–120 | 0.2–0.4 | 1–3 |
| Finishing (carbide) | 50–80 | 0.1–0.2 | 0.5–1.0 |
| Finishing (ceramic) | 100–150 | 0.05–0.15 | 0.2–0.5 |
| Finishing (CBN) | 150–250 | 0.05–0.1 | 0.1–0.3 |
The key point is that the cutting speed must be high enough to avoid work hardening but not so high that the tool fails due to excessive heat. The feed rate should be moderate to avoid excessive cutting forces, and the depth of cut should be sufficient to remove the work-hardened layer from the previous pass.
3. Engineering Practice and Lessons Learned
3.1 The Challenge of Machining Stellite Surfacing
From my experience with turbine components and valve parts, machining Stellite surfacing is one of the most challenging operations in the shop. The material is hard, abrasive, and tends to work-harden. The tool wear is rapid, and the surface finish is difficult to control.
The paper's recommendation to use different tool materials for roughing and finishing is sound. In practice, I have found that the roughing operation should be planned to remove most of the material with carbide tools, leaving a small allowance for finishing with ceramic or CBN tools.
3.2 Practical Considerations for Tool Life
Tool life is a major concern when machining Stellite alloys. The paper discusses the factors that affect tool life, including cutting speed, feed rate, and tool material.
| Factor | Effect on Tool Life | Practical Recommendation |
|---|---|---|
| Cutting speed | Higher speed reduces tool life | Use the lowest speed that achieves acceptable productivity |
| Feed rate | Higher feed increases tool life but worsens finish | Balance feed rate against surface finish requirements |
| Tool material | CBN has the longest tool life | Use CBN for finishing operations |
| Coolant | Reduces tool temperature, extends life | Use flood coolant or high-pressure coolant |
In practice, I have found that the use of coolant is essential for machining Stellite alloys. The coolant reduces the tool temperature, prevents work hardening, and flushes away the chips.
3.3 Common Machining Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Tool chipping | Excessive cutting force, interrupted cut | Reduce feed rate, use stronger tool geometry |
| Tool wear | Abrasive carbides in Stellite | Use harder tool material, reduce cutting speed |
| Work hardening | Insufficient depth of cut | Use sufficient depth of cut to remove work-hardened layer |
| Poor surface finish | Tool wear, vibration | Use sharp tool, reduce feed rate, improve rigidity |
| Built-up edge | Low cutting speed, high temperature | Increase cutting speed, use coolant |
4. Key Questions and Reflections
The paper raises an important question: what is the most economical way to machine Stellite surfacing? The answer depends on the volume of work, the required surface finish, and the cost of tooling.
From my experience, the most economical approach is to use carbide tools for roughing and ceramic tools for finishing. CBN tools are expensive but may be justified for high-volume production or where surface finish is critical.
Another important question is whether the Stellite surfacing should be machined before or after heat treatment. In general, machining after heat treatment is preferred because the heat treatment can cause distortion that would be removed by machining. However, the Stellite alloy is harder after heat treatment, which increases the machining difficulty.
5. Study Insights and Implications
The paper provides valuable practical guidance for machining Stellite alloys. The key insights are:
- Tool selection is critical: carbide for roughing, ceramic or CBN for finishing.
- Cutting parameters must be carefully controlled to avoid work hardening and tool failure.
- Coolant is essential for tool life and surface finish.
- The machining allowance must be sufficient to remove the work-hardened layer from the previous pass.
The paper's comparison of cutting performance for different tool materials is particularly useful. It provides a practical reference for selecting the right tool for each operation.
6. Reference Value and Outlook
This paper is a valuable reference for engineers involved in machining Stellite alloys and similar hard-facing materials. The practical guidance on tool selection and cutting parameters is directly applicable to production.
Looking forward, the trend is toward using advanced tool materials such as CBN and PCD (polycrystalline diamond) for finishing operations. These tools offer longer tool life and better surface finish, but at a higher cost.
The paper also highlights the importance of process planning. The machining of Stellite surfacing should be planned as a multi-step process, with roughing, semi-finishing, and finishing operations, each with appropriate tooling and parameters.
Zhuojin Pipe Fitting Co., Ltd