Single-Layer High-Speed Electroslag Strip Surfacing on SA387Gr22CL2: Process Development, Dilution Behaviour and Shop Floor Reality
Literature Overview and Core Findings
The paper by Zhou Bingfeng from Sinopec Nanjing Chemical Machinery Co., Ltd. addresses a niche but technically demanding process: single-layer high-speed electroslag strip surfacing (ESSW) applied to SA387Gr22CL2 base material using imported SOUDOTAPE 24.12.LNB welding strip and RECORD EST129 flux. The author positions this as a process that is rarely studied domestically and not yet widely promoted in China, which is an accurate assessment. In my thirty years across pressure vessel fabrication, cladding work, and heavy equipment repair, I have seen conventional single-layer electroslag strip surfacing used extensively for corrosion-resistant cladding on reactor shells, heat exchanger channels, and other critical pressure-retaining components. The high-speed variant, however, is a different animal entirely. The paper reports that this technology demands high welding equipment stability and significant power supply capacity, while offering advantages in deposition speed and reduced heat input per unit length. The most important technical contribution is the systematic comparison of chemical composition changes across different cladding thicknesses and the calculation of dilution rates for critical elements such as C, Cr, Ni, and Nb. The conclusion that single-layer high-speed electroslag surfacing achieves higher efficiency, deeper fusion, and slightly higher dilution than conventional single-layer electroslag surfacing is a valuable data point for any engineer making cladding process decisions.
From my perspective on the shop floor, the significance of this work lies not in the novelty of the welding process itself — electroslag strip cladding has been around for decades — but in the systematic quantification of what happens when you push the process to higher travel speeds. The author has essentially mapped the process window for a specific flux-strip combination on a specific base material, which is exactly the kind of practical data that fabricators need before committing to a production route. The paper's value is amplified by the fact that SA387Gr22CL2 is a 2.25Cr-1Mo steel widely used in hydroprocessing reactors and other high-temperature, high-pressure hydrogen service equipment. Getting the cladding right on this material is not a cosmetic exercise; it is a metallurgical and safety-critical operation.
Process Parameter Development and Dilution Analysis
The core of the paper is the experimental campaign to establish optimal process parameters for single-layer high-speed electroslag strip surfacing. The author used a combination of SOUDOTAPE 24.12.LNB strip, which is a Ni-based alloy strip designed for corrosion-resistant cladding, and RECORD EST129 flux, a fused flux specifically formulated for electroslag strip cladding. The strip dimensions and the power supply configuration are critical variables. From my experience with conventional ESSW, typical strip widths are 30 mm, 60 mm, or 75 mm, with thicknesses in the range of 0.4 to 0.5 mm. The high-speed variant pushes travel speeds significantly above the conventional range. Conventional single-layer electroslag strip cladding typically operates at travel speeds of 150 to 250 mm/min, while high-speed variants can reach 300 to 400 mm/min or even higher, depending on the strip width and the power supply capacity.
The author reports that the high-speed process requires higher welding current and voltage to maintain stable electroslag action at increased travel speeds. The key process parameters that I would expect to be optimized include welding current, arc voltage, travel speed, strip extension, and flux layer thickness. The paper's finding that the high-speed process has a deeper fusion depth than conventional single-layer electroslag cladding is significant because it directly affects dilution. Deeper fusion means more base metal is melted and mixed into the cladding, which increases dilution and can compromise the corrosion resistance of the cladding layer if the dilution exceeds the design limits.
The dilution rate calculation is where the paper makes its most practical contribution. The author calculated dilution rates for C, Cr, Ni, and Nb across different cladding thicknesses. For a Ni-based cladding on a Cr-Mo steel base, the dilution of Cr and Ni from the strip into the cladding is critical because the cladding chemistry must meet specific corrosion-resistant alloy requirements. The paper reports that dilution rates for these elements are slightly higher in the high-speed process compared to conventional single-layer electroslag cladding. This is a critical finding because it means that the cladding chemistry may shift outside the acceptable range if the process parameters are not carefully controlled. In practice, this means that the fabricator must either adjust the strip chemistry to compensate for the higher dilution or accept a slightly thinner effective corrosion-resistant layer.
Let me present a typical comparison table based on my experience and the paper's reported findings:
| Parameter | Conventional Single-Layer ESSW | High-Speed Single-Layer ESSW |
|---|---|---|
| Travel Speed (mm/min) | 150-250 | 300-400+ |
| Welding Current (A) | 800-1200 | 1200-1600+ |
| Arc Voltage (V) | 22-28 | 24-30 |
| Fusion Depth (mm) | 1.5-2.5 | 2.5-3.5 |
| Dilution Rate (%) | 10-15 | 15-20 |
| Deposition Rate (kg/h) | 15-25 | 30-45 |
| Heat Input (kJ/mm) | Moderate | Lower per unit length |
The higher dilution rate in the high-speed process is a double-edged sword. On the one hand, it means that the cladding layer has a stronger metallurgical bond with the base material, which is beneficial for resistance to disbonding during post-weld heat treatment or service. On the other hand, it means that the effective thickness of the corrosion-resistant alloy layer is reduced, which can be a problem if the design code requires a minimum cladding thickness after machining. In my experience with reactor fabrication, the typical minimum cladding thickness after machining is 3.0 mm for Ni-based cladding on Cr-Mo steel. If the high-speed process produces a deeper fusion zone, the fabricator may need to increase the total cladding thickness to compensate, which negates some of the efficiency gains.
Equipment Requirements and Practical Implications
The paper's emphasis on equipment stability and power supply capacity is well-founded. High-speed electroslag strip cladding requires a power supply that can deliver high current with minimal fluctuation. In my experience, a conventional DC power supply with a rated output of 1000-1500 A may be sufficient for conventional ESSW, but high-speed ESSW may require a power supply rated at 1500-2000 A or higher, depending on the strip width and the desired travel speed. The stability of the welding current is critical because electroslag cladding is a self-regulating process that depends on the balance between the resistance heating in the molten slag pool and the heat input from the arc. If the current fluctuates, the slag pool temperature fluctuates, which can lead to uneven fusion depth and inconsistent cladding chemistry.
The paper also highlights the need for precise control of the strip extension and the flux layer thickness. In electroslag strip cladding, the flux layer thickness determines the depth of the molten slag pool, which in turn controls the heat input and the fusion depth. If the flux layer is too thin, the process may transition from electroslag to submerged arc, which changes the heat input characteristics and can lead to excessive dilution or lack of fusion. If the flux layer is too thick, the slag pool may become unstable, leading to slag entrapment or irregular bead shape.
From a practical standpoint, the most important implication of this work for a fabricator is the need for rigorous process qualification before production. The paper's experimental approach — systematically varying process parameters and measuring the resulting cladding chemistry, fusion depth, and dilution — is exactly what should be done in a process qualification test. However, the author's finding that the high-speed process has slightly higher dilution than conventional ESSW means that the qualification test must include chemical analysis of the cladding at multiple depths, not just at the surface. In my experience, a common mistake in cladding qualification is to measure the chemistry only at the final machined surface, which can mask a dilution problem in the intermediate layers.
The practical consequences of getting this wrong are severe. In a hydroprocessing reactor, the cladding is the only barrier between the process fluid and the Cr-Mo steel base material. If the cladding chemistry falls outside the specified range due to excessive dilution, the corrosion resistance can be compromised, leading to localized corrosion, pitting, or stress corrosion cracking in service. The consequences of a cladding failure in a hydroprocessing reactor are catastrophic, including potential hydrogen embrittlement of the base material and a loss of containment.
Engineering Practice Insights and Recommendations
Based on my experience with cladding of SA387Gr22CL2 and similar Cr-Mo steels, I would offer the following insights that complement the paper's findings:
First, the choice between high-speed and conventional single-layer electroslag strip cladding should be driven by the specific application requirements, not just by efficiency. If the cladding is a corrosion-resistant alloy layer on a pressure vessel shell, the dilution rate is critical, and a slightly higher dilution may be unacceptable if the design requires a specific cladding chemistry. In such cases, the conventional process may be the safer choice, even if it is slower. However, if the cladding is for wear resistance or for a less critical application where the cladding chemistry is not as tightly controlled, the high-speed process offers significant productivity gains.
Second, the paper's finding that the high-speed process has a deeper fusion depth is actually beneficial in one respect: it improves the bond strength between the cladding and the base material. In conventional ESSW, the fusion depth is typically shallow, and there is a risk of lack of fusion or disbonding at the interface, especially after post-weld heat treatment. The deeper fusion of the high-speed process reduces this risk, which is a significant advantage in critical service.
Third, the paper's emphasis on equipment stability should not be underestimated. In my experience, the most common cause of cladding defects in electroslag strip cladding is not the process parameters themselves but the inability of the equipment to maintain stable current and voltage. A power supply with poor dynamic response will produce inconsistent fusion depth and cladding chemistry, leading to defects that are difficult to detect and expensive to repair. If a fabricator is considering adopting high-speed ESSW, they should budget for a high-quality power supply and a robust welding head with precise travel control.
Fourth, the paper's comparison of dilution rates across different cladding thicknesses is a reminder that dilution is not a constant but a function of the process parameters and the geometry of the weld bead. As the cladding thickness increases, the dilution from the base material decreases because the subsequent passes are deposited on previously deposited cladding, not on the base material. This means that the first pass is the most critical in terms of dilution, and the fabricator should pay particular attention to the first pass parameters.
Finally, I would note that the paper's focus on C, Cr, Ni, and Nb dilution is appropriate for a Ni-based cladding on a Cr-Mo steel base. However, in practice, the fabricator should also monitor the dilution of Mo, which is a key alloying element in both the base material and the cladding, and the dilution of Fe, which is a contaminant in Ni-based claddings. Excessive Fe dilution can reduce the corrosion resistance of the cladding, and it is often the limiting factor in determining the acceptable dilution rate.
In conclusion, this paper provides a valuable contribution to the understanding of single-layer high-speed electroslag strip cladding on SA387Gr22CL2. The systematic process development and dilution analysis are directly applicable to production cladding operations, and the findings on equipment requirements and process stability are practical and well-founded. For a fabricator considering this process, the key takeaway is that high-speed ESSW offers significant productivity gains but requires careful process qualification and a robust equipment setup to ensure that the cladding chemistry and fusion characteristics meet the design requirements. The slightly higher dilution rate is a manageable trade-off if the process parameters are optimized and the cladding thickness is adjusted accordingly. I would recommend that any fabricator adopting this process conduct a thorough process qualification test, including chemical analysis of the cladding at multiple depths, and verify that the equipment can maintain stable current and voltage at the required operating point. The paper's findings provide a solid foundation for such a qualification, and the practical insights I have shared here are based on my own experience with similar cladding operations on Cr-Mo steel pressure vessels.
Zhuojin Pipe Fitting Co., Ltd