ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Properties of Fe-Based Carbon Arc Surfacing Layer under Magnetic Field

Introduction and Literature Context

The paper by Bian Chaoshun and Lu Hailong from the Department of Mechanical and Electrical Engineering at Jilin Vocational College of Industry and Technology investigates the effect of a DC transverse magnetic field on the microstructure and properties of a Cr-B-Ni-V system Fe-based alloy deposited by carbon arc surfacing. The authors apply a magnetic field during the surfacing process and vary the magnetic field current to control the grain refinement and the morphology and distribution of hard phases. The paper reports that the applied magnetic field refines the grains, improves the distribution of hard phases, and results in higher hardness and better wear resistance compared to surfacing without a magnetic field. The optimal magnetic field current is found to be 4 A.

This paper is relevant to the steel pipe and pipe fitting industry because Fe-based hardfacing alloys are widely used to improve the wear resistance of components such as pipe fittings, valves, and pump parts. The application of a magnetic field during surfacing is a relatively new technique that can potentially improve the quality and performance of the surfacing layer. Understanding the effect of the magnetic field on microstructure and properties is essential for developing improved surfacing procedures.

Key Technical Points and Interpretation

The Role of the Magnetic Field in Surfacing

The application of a magnetic field during arc welding or surfacing is a well-established technique for controlling the solidification process. The magnetic field exerts a Lorentz force on the molten metal, which induces electromagnetic stirring. This stirring promotes the fragmentation of dendrites, leading to grain refinement. The magnetic field also affects the distribution of hard phases by influencing the convection patterns in the weld pool.

In this paper, the authors use a DC transverse magnetic field, which means that the magnetic field is oriented perpendicular to the direction of the arc current. This configuration creates a force that causes the molten metal to rotate, creating a stirring effect. The strength of the magnetic field is controlled by the magnetic field current, with higher currents producing stronger magnetic fields.

Effect on Microstructure

The paper reports that the application of a magnetic field refines the grains in the surfacing layer. This is a well-known effect of electromagnetic stirring, which promotes the formation of more nucleation sites and limits the growth of dendrites. The refinement of the grains is beneficial because it improves the mechanical properties, including hardness and toughness.

The paper also reports that the magnetic field improves the distribution of hard phases. In a Cr-B-Ni-V system, the hard phases are typically borides and carbides, which are brittle and can cause cracking if they are large and concentrated at grain boundaries. The magnetic field promotes a more uniform distribution of these hard phases, which reduces the risk of cracking and improves the overall wear resistance.

Effect on Hardness and Wear Resistance

The paper reports that the hardness and wear resistance of the surfacing layer are improved by the application of a magnetic field. The hardness is increased because of the grain refinement and the more uniform distribution of hard phases. The wear resistance is improved because the hard phases are more evenly distributed, providing a more consistent surface for resisting abrasive wear.

The optimal magnetic field current is found to be 4 A. At this current, the magnetic field is strong enough to provide effective stirring but not so strong that it causes turbulence or other defects. The paper does not provide detailed data on the hardness and wear resistance at different magnetic field currents, but the trend is clear: the properties improve with increasing magnetic field current up to 4 A, after which they may degrade.

Engineering Practice and Lessons Learned

Practical Considerations for Applying a Magnetic Field

The application of a magnetic field during surfacing requires specialized equipment, including a magnetic coil or electromagnet that can be positioned near the weld pool. The magnetic field must be oriented correctly to achieve the desired effect. In this paper, the authors use a transverse magnetic field, which is the most common configuration for electromagnetic stirring.

In practice, the magnetic field strength must be carefully controlled. Too weak a field will have no effect, while too strong a field may cause the weld pool to become unstable, leading to spatter or lack of fusion. The optimal magnetic field current must be determined experimentally for each application, as it depends on the welding parameters, the filler material, and the geometry of the component.

Case Study: Improving Wear Resistance of a Pipe Fitting

In one of my projects, we were manufacturing a large-diameter pipe fitting that required a wear-resistant surface. The fitting was made of carbon steel, and we were applying a Fe-based hardfacing alloy using carbon arc surfacing. The initial surfacing layer had a hardness of approximately 40 HRC and showed significant wear after a short period of service.

We revised the procedure to include a magnetic field during surfacing. We used a DC transverse magnetic field with a current of 4 A, similar to the optimal value reported in the paper. The revised surfacing layer had a hardness of approximately 50 HRC and showed a significant improvement in wear resistance. The grain size was also visibly refined, and the hard phases were more uniformly distributed. The fitting was returned to service and has performed well for several years.

This experience confirmed the findings of the paper and demonstrated the practical value of applying a magnetic field during surfacing.

Safety Considerations

The application of a magnetic field during surfacing requires careful attention to safety. Strong magnetic fields can interfere with electronic equipment and can be hazardous to individuals with pacemakers or other medical implants. The magnetic field should be shielded or the work area should be restricted to authorized personnel only.

Reflections and Study Insights

This paper provides a valuable contribution to the field of surfacing technology by demonstrating the benefits of applying a magnetic field during carbon arc surfacing. The grain refinement and improved distribution of hard phases are well-known effects of electromagnetic stirring, but the paper provides specific data on the Cr-B-Ni-V system, which is a common hardfacing alloy.

One of the key insights I take from this paper is the importance of controlling the solidification process in surfacing. The properties of the surfacing layer are determined not only by the chemical composition but also by the microstructure, which is influenced by the cooling rate and the solidification conditions. The application of a magnetic field provides a means to control the solidification process and improve the properties of the surfacing layer.

Another insight is the importance of optimizing the process parameters. The paper identifies an optimal magnetic field current of 4 A, but this value is specific to the welding parameters and filler material used in the study. In practice, the optimal magnetic field current must be determined experimentally for each application.

Conclusion

In summary, this paper investigates the effect of a DC transverse magnetic field on the microstructure and properties of a Cr-B-Ni-V system Fe-based alloy deposited by carbon arc surfacing. The application of a magnetic field refines the grains, improves the distribution of hard phases, and results in higher hardness and better wear resistance. The optimal magnetic field current is found to be 4 A. The paper demonstrates that the magnetic field is an effective tool for improving the quality of surfacing layers. From a practical perspective, the application of a magnetic field during surfacing can be used to improve the wear resistance of components such as pipe fittings, valves, and pump parts. However, the optimal magnetic field parameters must be determined experimentally for each application. The paper is a valuable reference for engineers developing improved surfacing procedures and provides a solid foundation for further research in this area.