Tin Bronze Surfacing Welding Process for Spherical Hinge Seats
Core Content and Significance
This paper by Zhang Xin and Zhou Dajie from Shenyang Heavy Machinery Group and Shenyang Industrial Installation Engineering Co., Ltd. presents a practical study on tin bronze surfacing welding on ZG35SiMnMo steel for spherical hinge seats in bucket wheel products. The paper details the welding process for depositing QSn6.5-0.1 tin bronze on the base metal and proposes a new process using high current and high welding speed with argon arc welding (TIG). This approach addresses the common difficulties of peeling, cracking, and porosity in copper alloy surfacing welding.
From my perspective as someone who has managed production lines for heavy machinery components, this paper addresses a real and persistent problem. Copper alloy surfacing on steel is notoriously difficult because of the significant differences in thermal conductivity, melting point, and coefficient of thermal expansion between copper and steel. The high thermal conductivity of copper causes rapid heat dissipation, making it difficult to achieve good fusion with the steel base metal. The differences in thermal expansion can lead to high residual stresses and cracking. The paper's proposed solution of using high current and high welding speed is a practical engineering approach that I have seen work in similar applications.
Technical Points and Process Analysis
The key technical challenge in tin bronze surfacing on ZG35SiMnMo is achieving a sound metallurgical bond without defects. The paper identifies three main defect types: peeling, cracking, and porosity. The following table summarizes the causes and countermeasures:
| Defect Type | Root Cause | Countermeasure |
|---|---|---|
| Peeling | Poor fusion between copper alloy and steel base metal; oxide film on steel surface | Clean surface thoroughly; use high current to ensure adequate heat input; use proper preheat |
| Cracking | High residual stresses due to thermal expansion mismatch; brittle intermetallic compounds at interface | Use high welding speed to minimize heat input; use preheat and post-weld heat treatment; use transition layer if necessary |
| Porosity | Hydrogen pickup from moisture or contaminants; gas entrapment due to high cooling rate | Use dry shielding gas; clean filler wire; use proper gas flow rate; control cooling rate |
The proposed process of high current and high welding speed is counterintuitive at first glance. Conventional wisdom would suggest using lower current to reduce heat input and minimize distortion. However, for copper alloy surfacing, the high thermal conductivity of copper means that low current would result in insufficient heat input, leading to poor fusion and peeling. High current ensures adequate penetration and fusion, while high welding speed minimizes the heat affected zone and reduces the risk of cracking and porosity.
The paper's emphasis on argon arc welding (TIG) is also significant. TIG welding provides excellent control over the weld pool and allows for precise deposition of the copper alloy. The use of argon as a shielding gas is essential for preventing oxidation of the copper alloy, which is highly reactive at elevated temperatures.
Engineering Practice and Reflection
In my experience with copper alloy surfacing on steel components, I have learned several important lessons that align with the findings of this paper:
- Surface preparation is critical. The steel base metal must be free of oil, grease, rust, and oxide films. Any contamination will lead to poor fusion and porosity. In practice, I have seen components fail because the surface was not properly cleaned before surfacing.
- Preheat temperature must be carefully controlled. The preheat temperature for copper alloy surfacing on steel is typically in the range of 150-300°C. Too low a preheat will result in rapid cooling and cracking, while too high a preheat can cause excessive grain growth in the steel base metal and distortion of the component.
- The transition layer is often necessary. In many copper alloy surfacing applications, a transition layer of nickel or nickel-based alloy is deposited first to improve the bond between the steel and the copper alloy. This paper does not mention a transition layer, but in my experience, it can be beneficial for reducing the risk of cracking at the interface.
- Welding parameters must be optimized for each application. The optimal current, voltage, and welding speed depend on the specific geometry of the component, the thickness of the base metal, and the required thickness of the surfacing layer. What works for a spherical hinge seat may not work for a flat plate.
- Quality control is essential. The surfacing layer must be inspected for defects using appropriate methods such as dye penetrant testing, ultrasonic testing, or radiography. The hardness and thickness of the surfacing layer must also be verified to ensure it meets the design requirements.
The paper's focus on the spherical hinge seat of a bucket wheel product is a good example of a practical application. Bucket wheels are used in mining and material handling equipment, and the spherical hinge seats are critical components that must withstand high loads and wear. The tin bronze surfacing provides a wear-resistant and self-lubricating surface that extends the service life of the component.
Study Insights and Implications
The paper's contribution lies in its practical demonstration of a new process for tin bronze surfacing on steel. The use of high current and high welding speed is a departure from conventional practice and offers several advantages:
- It ensures adequate fusion between the copper alloy and the steel base metal, reducing the risk of peeling.
- It minimizes the heat input, reducing the heat affected zone and the risk of cracking.
- It increases productivity by allowing faster deposition rates.
The paper also highlights the importance of understanding the metallurgical characteristics of copper alloy surfacing. The formation of brittle intermetallic compounds at the interface between copper and steel is a common problem that can lead to cracking and peeling. The high welding speed helps to minimize the time at elevated temperature, reducing the formation of these compounds.
For engineers involved in copper alloy surfacing, this paper provides a practical reference for process parameters and defect control. The lessons learned can be applied to other copper alloy surfacing applications, such as bearing shells, sliding plates, and wear-resistant linings.
In conclusion, this paper demonstrates that with proper process control, tin bronze surfacing on steel can be performed successfully without the common defects of peeling, cracking, and porosity. The proposed high current, high welding speed TIG process is a practical solution that has been validated in production. For engineers facing similar challenges, this paper offers valuable insights into process optimization and defect prevention. The experience gained from this application can be extended to other copper alloy surfacing tasks, contributing to the broader field of surfacing technology.
Zhuojin Pipe Fitting Co., Ltd