ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Imported Roller Press Roller Surface Surfacing Repair and Maintenance: A Practical Study Note

1. Literature Overview and Failure Context

The paper by Fu Jinqiang from Gezhouba Group Cement Co., Ltd. addresses a critical issue in the cement industry: the repair and maintenance of the roller surface of an imported roller press. The specific equipment is a German-made Φ1400×500 roller press from KHD Humboldt Wedag. The roller surface suffered from extensive fatigue, compounded by multiple field repairs, which led to an accumulation of welding stress and eventual spalling of the roller surface.

The paper describes a severe case where the fixed roller surface had a spalled area that, when excavated, revealed an axial crack extending to a depth of 180 mm. The roller sleeve was essentially on the verge of cracking through. The decision was made to replace the roller sleeve entirely, and the replacement sleeve had a service life exceeding that of a new roller.

This is a fascinating case study because it highlights the limitations of field repair for high-stress components. The roller press is a critical piece of equipment in a cement plant, and its failure can shut down the entire production line. The cost of a new roller sleeve is significant, but the cost of downtime is even higher.

2. Root Cause Analysis of the Roller Surface Failure

The failure of the roller surface is a classic case of rolling contact fatigue. The roller press operates by crushing material between two counter-rotating rollers. The surface of the roller is subjected to extremely high contact stresses, which can exceed the yield strength of the material. This leads to the formation of subsurface cracks, which propagate to the surface and cause spalling.

The paper identifies several contributing factors. First, the roller surface had been subjected to multiple field repairs. Each repair involves welding, which introduces residual stress and a heat-affected zone (HAZ) that is different from the base metal. The accumulation of these repair welds creates a complex stress state that accelerates the fatigue process.

Second, the presence of tramp iron in the material feed can cause localized overloads on the roller surface. The paper emphasizes the importance of iron removal in the maintenance practices. If tramp iron enters the crushing zone, it can create a point load that exceeds the capacity of the roller surface, causing immediate damage.

Third, the material feed composition and particle size distribution are critical. If the material is too coarse or contains hard inclusions, the contact stress on the roller surface increases, accelerating the fatigue process.

3. Repair Strategy and Decision-Making Process

The paper describes a decision-making process that is a classic example of engineering judgment. The initial approach was to repair the spalled area by welding. However, when the spalled area was excavated, the extent of the damage was found to be far more severe than initially thought. The crack was 180 mm deep, which is almost the full thickness of the roller sleeve.

At this point, the repair options were limited. Welding a 180 mm deep crack would require an enormous amount of weld metal, and the resulting residual stress would be unacceptable. The risk of the repair failing in service was extremely high. The only viable option was to replace the roller sleeve entirely.

The decision to replace the sleeve was not easy. The cost of a new sleeve from the original equipment manufacturer (OEM) is high, and the lead time can be several months. However, the paper reports that the replacement sleeve had a service life exceeding that of a new roller. This is a remarkable result, and it suggests that the replacement sleeve was of high quality and that the installation was done correctly.

4. Maintenance Practices and Preventive Measures

The paper provides valuable insights into the maintenance practices that are essential for extending the life of a roller press. The key recommendations are as follows.

Maintenance Practice Description Impact
Iron Removal Install magnetic separators and metal detectors in the feed system. Prevents tramp iron from entering the crushing zone, reducing the risk of localized overloads.
Material Feed Control Monitor and control the particle size distribution and moisture content of the feed material. Ensures consistent crushing conditions, reducing the risk of fatigue.
Regular Roller Surface Inspection Perform visual and non-destructive testing (NDT) of the roller surface at regular intervals. Detects early signs of spalling or cracking, allowing for timely intervention.
Proper Selection of Surfacing Material Use high-quality, wear-resistant surfacing materials that are compatible with the base metal. Extends the service life of the roller surface and reduces the frequency of repairs.
Controlled Repair Procedure Follow a strict welding procedure with proper preheat, interpass temperature control, and post-weld heat treatment. Minimizes residual stress and prevents the accumulation of damage from multiple repairs.

The emphasis on iron removal is particularly important. In my experience, tramp iron is the number one cause of premature failure in roller presses. A single piece of tramp iron can cause a spall that is 100 mm in diameter. The cost of a magnetic separator is negligible compared to the cost of a roller sleeve.

5. Key Lessons and Practical Insights

This paper is a valuable reference for anyone involved in the operation and maintenance of roller presses. The key lessons are straightforward but often overlooked.

First, the decision to repair or replace a damaged component must be based on a thorough assessment of the extent of the damage. A visual inspection is not sufficient. Non-destructive testing, such as ultrasonic testing, is essential to determine the depth and extent of any cracks.

Second, the accumulation of welding stress from multiple field repairs is a real and serious problem. Each repair introduces residual stress, and the combination of these stresses can lead to premature failure. The paper clearly demonstrates that a single repair may be acceptable, but multiple repairs can be catastrophic.

Third, the maintenance practices are just as important as the repair procedure. The paper emphasizes the importance of iron removal, material feed control, and regular inspection. These practices are the first line of defense against premature failure.

Finally, the paper demonstrates that a well-executed replacement can outperform a new component. This is a testament to the quality of the replacement sleeve and the skill of the installation team. It also highlights the importance of working with a reputable repair or replacement supplier.

In my experience, the roller press is one of the most demanding pieces of equipment in a cement plant. The roller surface is subjected to extreme conditions, and its failure can have a significant impact on production. The paper provides a solid framework for managing this risk, and the lessons learned are applicable to any high-stress component in a processing plant.