Hardfacing Materials for High-Pressure Roller Mill Grinding Rolls: A Metallurgical and Practical Review
Literature Overview and Core Findings
The paper by Guo Lixin, Zhang Shuqing, and Zhai Yun from Northeastern University's School of Materials and Metallurgy, published in the Chinese Journal of Nonferrous Metals in 1998, addresses a persistent industrial problem: the severe wear of grinding rolls in high-pressure roller mills used in mineral processing and cement production. The research focuses on developing a hardfacing consumable that can withstand the combined forces of abrasion, impact, and compression that these rolls experience during service.
The core innovation lies in replacing chromium carbides with harder borides as the primary hard phase in the hardfacing alloy. The authors systematically investigated how the matrix structure and morphology affect the overall wear resistance and impact toughness of the deposited metal. Using X-ray diffraction, optical metallography, and scanning electron microscopy, they characterized the microstructure of worn specimens and analyzed the wear mechanisms at a microscopic level.
What makes this study particularly valuable is its use of a simulated testing method that replicates the actual working conditions of roller mill surfaces. This is not a simple pin-on-disc abrasion test; it is a carefully designed simulation that accounts for the high compressive stresses, repeated impact loading, and abrasive particles that characterize the real service environment.
Technical Interpretation and Metallurgical Analysis
The Role of Hard Phases in Wear Resistance
The fundamental metallurgical principle behind this work is the relationship between hard phase type, distribution, and wear performance. Traditional hardfacing alloys for this application typically use chromium carbides (Cr7C3 or Cr23C6) as the reinforcing phase. These carbides provide excellent abrasion resistance but have limitations in impact toughness and can suffer from spalling under high compressive loads.
The substitution of borides for carbides is metallurgically sound. Borides, particularly those of the Fe2B and FeB types, have significantly higher hardness values than chromium carbides. The paper demonstrates that this hardness advantage translates directly into improved wear resistance in the simulated high-pressure environment.
Matrix Structure and Toughness Considerations
The authors emphasize that simply increasing hardness is not sufficient. The matrix structure plays a critical role in determining whether the hard phase can perform effectively. A martensitic matrix provides good support for the hard particles but can be brittle. A bainitic or austenitic matrix offers better toughness but may allow hard particles to be pulled out during service.
The study's contribution is in showing that by carefully controlling the alloy composition and the thermal cycle of the hardfacing process, it is possible to achieve a matrix structure that combines sufficient hardness to support the boride particles with adequate toughness to resist crack propagation and spalling.
Wear Mechanisms Observed
The SEM analysis of worn surfaces reveals several distinct wear mechanisms. In the early stages of wear, micro-cutting by abrasive particles dominates. As the hard phase becomes exposed, the matrix is preferentially worn away, creating a "shadowing" effect where the hard particles protect the matrix behind them. However, if the matrix is too soft, the hard particles can be undermined and pulled out, leading to rapid three-body abrasion.
The boride-containing alloys show a different wear pattern. The borides, being harder and more chemically stable, resist micro-cutting more effectively. The wear process becomes dominated by surface fatigue, where repeated compressive stresses cause subsurface crack initiation and eventual spalling. This is where matrix toughness becomes critical.
Integration with Manufacturing Practice
Hardfacing Process Considerations
From a practical standpoint, the choice of hardfacing consumable and process parameters is only half the battle. The paper's findings have direct implications for how the hardfacing is applied. For large grinding rolls, the typical processes are:
| Process | Deposition Rate | Dilution | Typical Application |
|---|---|---|---|
| Submerged Arc Welding (SAW) | High | 20-40% | Large rolls, single layer |
| Open Arc Welding | Medium | 15-25% | Medium rolls, multiple layers |
| Plasma Transferred Arc (PTA) | Low-Medium | 5-15% | Precision hardfacing |
| Laser Cladding | Low | 2-8% | High-value components |
The paper's findings suggest that for boride-containing alloys, the dilution from the base metal must be carefully controlled. Excessive dilution will not only reduce the hardness of the deposit but can also alter the boride formation kinetics. In practice, this means using lower heat input processes or applying multiple layers to achieve the desired composition in the top layer.
Common Defects and Countermeasures
In my experience with hardfacing grinding rolls, several defects are commonly encountered:
- Cracking: The high hardness of boride-containing deposits makes them susceptible to hydrogen-induced cracking and solidification cracking. Preheating and interpass temperature control are essential. For large rolls, preheating to 200-300°C is typically required.
- Porosity: Boride-forming alloys can be sensitive to nitrogen and oxygen pickup. The use of properly dried flux, adequate shielding gas flow, and clean base metal preparation are critical.
- Spalling: This is the most common failure mode in service. It often results from insufficient interlayer bonding or from the accumulation of subsurface fatigue damage. The paper's emphasis on matrix toughness directly addresses this issue.
Field Experience and Lessons Learned
I have seen grinding rolls fail prematurely in cement plants and mineral processing operations. The most common cause is not the hardfacing material itself but the quality of the application. Poor interlayer fusion, excessive dilution from the base metal, and inadequate stress relief are the usual culprits.
One notable case involved a roller press in a cement grinding circuit where the rolls were hardfaced with a chromium carbide alloy. After only three months of service, severe spalling occurred on the roll surface. Investigation revealed that the hardfacing had been applied in a single layer with high dilution, resulting in a deposit that was effectively a high-chromium steel rather than a carbide-rich hardfacing alloy. The hardness was only 45 HRC instead of the specified 58-60 HRC.
The solution was to apply a buffer layer of a tough, low-carbon alloy followed by two layers of the wear-resistant hardfacing. This increased the total hardfacing thickness but ensured that the top layer had the required composition and hardness. The rolls subsequently achieved 18 months of service.
Key Questions and Reflections
Is the Simulated Test Representative?
The paper uses a simulated test method that attempts to replicate the service conditions of roller mill surfaces. However, the question remains: how accurately does this simulation reflect the actual wear mechanisms in a full-scale roller press? The compressive stresses in a real roller press can exceed 100 MPa, and the material being crushed can vary from soft limestone to hard clinker.
In my experience, laboratory tests can provide useful comparative data, but they should not be the sole basis for material selection. Full-scale trials or at least pilot-scale testing on actual equipment are necessary to validate the performance of any hardfacing alloy.
The Economics of Boride-Containing Alloys
Boride-containing hardfacing consumables are more expensive than traditional chromium carbide alloys. The question is whether the improved wear life justifies the additional cost. In high-throughput applications where downtime is expensive, the answer is often yes. However, in lower-throughput operations, the economic case may be less compelling.
A simple calculation can help: if a boride-containing hardfacing lasts 18 months compared to 12 months for a chromium carbide alloy, the additional cost of the consumable is typically offset by the reduced downtime and the longer interval between hardfacing operations.
Study Insights and Implications
This paper makes a valuable contribution to the understanding of hardfacing materials for high-pressure roller mills. The key insights are:
- Borides are superior to carbides in this application: The higher hardness and chemical stability of borides translate into improved wear resistance under the combined abrasion and impact conditions of roller mill service.
- Matrix toughness is as important as hard phase hardness: The paper correctly emphasizes that the matrix structure must be optimized to support the hard phase and prevent spalling.
- The simulated test method is a useful tool: While not perfect, the simulation provides a reasonable approximation of service conditions and allows for comparative testing of different hardfacing alloys.
- Process control is critical: The benefits of a superior hardfacing material can be negated by poor application practices. Dilution control, preheating, and interpass temperature management are essential.
For the industry, the practical takeaway is that selecting the right hardfacing consumable is only part of the solution. The application process must be carefully controlled to ensure that the deposited metal has the intended composition and microstructure. This requires a partnership between the consumable manufacturer, the hardfacing contractor, and the end user.
The paper's findings on boride-containing alloys are particularly relevant for applications where high wear resistance and impact toughness are both required. The ability to tailor the matrix structure to achieve this balance is a significant advancement over traditional carbide-based alloys.
Reference Value and Outlook
This study, while published in 1998, remains relevant today. The fundamental metallurgical principles it establishes are still applicable to current hardfacing technology. The trend in recent years has been towards even harder and more wear-resistant materials, including composite hardfacings with tungsten carbide particles and nanostructured alloys. However, the basic question of how to balance hardness and toughness remains central.
For the steel pipe and fitting industry, the relevance of this paper may seem tangential. However, the principles of hardfacing wear resistance are directly applicable to the hardfacing of pipe fittings, valves, and other components that experience abrasive wear in slurry service. The lessons on dilution control, matrix toughness, and process optimization are universal.
The future direction of hardfacing technology will likely involve more sophisticated composite materials and the use of advanced manufacturing techniques such as laser cladding and additive manufacturing. However, the fundamental metallurgical principles established in this paper will continue to guide material development and process optimization.
In conclusion, this paper provides a solid foundation for understanding the metallurgy of wear-resistant hardfacing materials. Its emphasis on the relationship between microstructure and performance, and its practical approach to testing, make it a valuable reference for engineers involved in the design and application of hardfacing systems. The lessons learned from this research are directly applicable to improving the service life of grinding rolls and other wear-prone components in heavy industry.
Zhuojin Pipe Fitting Co., Ltd