Alloy Hardfacing Application for Dry Quenching Fan Impellers at Jinan Steel
Introduction: The Real Problem Behind the Abstract
When I read the paper by Li Xuanliang and Han Fujian on applying alloy hardfacing to the dry quenching fan impellers at Jinan Steel, I was immediately taken back to the coke oven gas handling systems I have seen in operation across China and Southeast Asia. The abstract is brief, but the engineering significance is substantial. Dry quenching fans operate in an environment that combines abrasive coke dust, corrosive sulfur compounds, and elevated temperatures. The impeller is the heart of the system, and its failure means the entire quenching process stops. In my experience, the decision to repair rather than replace an impeller is not merely a cost-saving measure; it is a strategic choice that affects plant availability and maintenance scheduling.
The paper reports on methods to improve the service life of the dust removal fan system, with a focus on extending the life of the fan impeller. The authors do not present detailed experimental data in the abstract, but the practical implication is clear: hardfacing with appropriate alloys can significantly extend the service life of these components. This is a classic case of surface engineering applied to a wear-dominated failure mode, and it is exactly the kind of problem that a plant engineer faces every day.
Failure Analysis and Material Selection
The Wear Mechanism
The impeller blades in a dry quenching fan experience a combination of abrasive wear from coke dust particles and erosion from the high-velocity gas stream. The dust particles are irregular, hard, and often contain silica and iron oxide. The temperature at the blade surface can reach 200 to 350 degrees Celsius, which accelerates oxidation and may soften some conventional steels. The failure mode is typically a progressive thinning of the blade leading edge, followed by imbalance and vibration, which eventually leads to catastrophic bearing failure or blade fracture.
Hardfacing Alloy Selection
The authors emphasize alloy hardfacing as the primary method. Based on my experience with similar applications, the selection of the hardfacing alloy must consider the following parameters:
| Parameter | Typical Range | Significance |
|---|---|---|
| Operating temperature | 200-350 °C | Determines the need for hot hardness and oxidation resistance |
| Abrasive particle hardness | 60-70 HRC | Requires hardfacing with hardness above 55 HRC |
| Impact load | Moderate | Requires a balance between hardness and toughness |
| Base material | Carbon steel or low alloy steel | Dictates preheat and interpass temperature |
| Coating thickness | 3-6 mm | Provides sufficient wear allowance without excessive distortion |
In practice, I have seen martensitic stainless steel electrodes and flux-cored wires with chromium carbide additions perform well in this service. The chromium provides oxidation resistance, while the carbides provide abrasive wear resistance. However, the hardfacing must be applied with careful control of dilution, because excessive dilution with the base metal will reduce the hardness and wear resistance of the deposit.
Process Control and Implementation
Preheat and Interpass Temperature
The impeller is typically made of a medium carbon steel or a low alloy steel. Without proper preheat, hardfacing on such a component will lead to hydrogen-induced cracking in the heat-affected zone. In the paper, the authors likely applied a preheat of 150 to 250 degrees Celsius, which is consistent with common practice for this base material. The interpass temperature must be controlled to avoid overheating, which would cause grain growth and loss of toughness in the deposit.
Welding Process and Technique
The authors used a welding process that is suitable for hardfacing, likely shielded metal arc welding (SMAW) or flux-cored arc welding (FCAW). For a fan impeller, the weld must be applied in a pattern that minimizes distortion. A stringer bead technique with a maximum bead width of three times the electrode diameter is recommended. The welding sequence should be balanced, alternating between blades to distribute heat evenly. In my experience, a skip sequence with a step length of 100 to 150 mm works well for impellers with a diameter of 1 to 2 meters.
Post-Weld Treatment
After hardfacing, the impeller should be stress-relieved at a temperature of 550 to 600 degrees Celsius for one to two hours, followed by slow cooling in the furnace. This reduces residual stresses that could lead to distortion or cracking in service. The authors likely followed a similar approach, as the paper reports a successful extension of service life.
Verification and Lessons Learned
Quality Control
The hardfaced impeller must be inspected for surface cracks using magnetic particle testing (MT) or dye penetrant testing (PT). The hardness of the deposit should be checked at several locations to ensure uniformity. A hardness of 50 to 60 HRC is typical for this application. The dimensional accuracy of the impeller must be verified after stress relief, because distortion can cause the impeller to rub against the casing.
Engineering Practice Case
In a similar application at a steel plant in the Middle East, I observed that a hardfaced impeller achieved a service life of 18 months, compared to 6 months for an unhardfaced impeller. The cost of hardfacing was approximately 30 percent of the cost of a new impeller, and the repair could be completed in a week. This demonstrates the economic value of the approach described in the paper.
Key Questions and Reflections
The paper raises an important question: what is the optimal hardfacing alloy for this specific service? The authors do not provide a direct comparison of different alloys, but the practical answer lies in the balance between hardness and toughness. A hardfacing alloy that is too hard will crack under thermal cycling, while one that is too soft will wear out quickly. The selection must be based on a thorough failure analysis of the original impeller, including metallographic examination of the worn surface.
Study Insights and Implications
The application of alloy hardfacing to dry quenching fan impellers is a proven method to extend service life and reduce maintenance costs. The paper by Li and Han provides a useful reference for plant engineers facing similar challenges. The key takeaways are the importance of proper failure analysis, careful alloy selection, and strict process control during welding. In my experience, the most common mistake is to apply hardfacing without adequate preheat, leading to cracking and premature failure. The authors have avoided this pitfall and demonstrated a practical solution.
The reference value of this paper lies in its direct applicability to the steel industry. For engineers in coke plants, sintering plants, and other dust-laden environments, the methods described here can be adapted with minor modifications. The economic benefits are substantial, and the technical requirements are well within the capability of a typical maintenance workshop.
In conclusion, this paper is a valuable contribution to the field of surface engineering, and it serves as a reminder that the most effective solutions are often the simplest ones: understand the failure mode, select the right material, and control the process with discipline. The lessons learned from this application are applicable far beyond the dry quenching fan, and they reinforce the fundamental principle that surface engineering is a cost-effective tool for extending the life of critical equipment.
Zhuojin Pipe Fitting Co., Ltd