Quality Control in Nickel-Based Alloy Laser Powder Surfacing: Process Windows, Defects, and Composite Layers
Introduction: The Process and Its Challenges
Nickel-based alloy surfacing is used to protect components from corrosion, high-temperature oxidation, and wear. The paper by Zhang Di, Shan Jiguo, and Ren Jialie from Tsinghua University investigates the quality of nickel-based alloy layers produced by laser beam powder surfacing. This is a sophisticated process that combines the precision of a laser with the flexibility of powder feeding. From my years supervising hardfacing operations, I know that nickel-based alloys are forgiving in some ways and unforgiving in others. They resist cracking better than iron-based hardfacing alloys, but they are prone to porosity and lack of fusion if the process parameters are not controlled.
Pre-Coat Geometry and Dilution Control
The paper identifies the pre-coat width and thickness as critical parameters. The pre-coat is the layer of powder that is placed on the substrate before the laser beam melts it. The paper states that the pre-coat width must be smaller than the laser beam diameter. If the pre-coat is wider than the beam, the edges of the powder layer are not melted, and the deposit will have unfused powder particles at the edges, creating a weak bond.
The pre-coat thickness also matters. A thicker pre-coat leads to poor bonding between the deposit and the substrate. This is because the laser beam must melt through the entire powder layer and then melt the substrate to achieve fusion. If the pre-coat is too thick, the beam energy is absorbed by the powder, and the substrate is not melted, resulting in lack of fusion. Conversely, if the pre-coat is too thin, the beam penetrates too deeply into the substrate, causing high dilution and a reduction in the deposit's hardness.
Table 1 summarises the effects of pre-coat geometry on deposit quality.
| Parameter | Too Small / Thin | Optimum | Too Large / Thick |
|---|---|---|---|
| Pre-coat width vs. beam diameter | Insufficient coverage, gaps in deposit | Width < beam diameter | Unmelted powder at edges |
| Pre-coat thickness | High dilution, low hardness | Moderate thickness | Poor bonding, lack of fusion |
| Laser power | Insufficient melting, porosity | Matched to pre-coat | Excessive dilution, spatter |
The practical implication is that the pre-coat must be applied with consistent thickness and width. In a production setting, this requires a powder feeder with accurate control and a substrate that is clean and flat. I have seen operators apply the pre-coat by hand, resulting in varying thickness, and the resulting deposit had alternating zones of high and low hardness.
Multi-Layer and Multi-Pass Strategies
The paper notes that multi-layer and multi-pass techniques are necessary to obtain large thickness and large-area deposits. A single pass can only produce a deposit of limited thickness, typically 1-3 mm. For a wear-resistant layer of 5-10 mm, multiple passes are required.
The defects that occur in multi-layer surfacing are transverse cracks, porosity at the weld toe, and lack of fusion between layers. Transverse cracks are caused by the accumulation of residual stress as each layer is deposited. The stress builds up because the deposit contracts on cooling, and the substrate constrains it. The solution is to control the heat input and to use a preheat or interpass temperature that reduces the thermal gradient.
Porosity at the weld toe is caused by the entrapment of gas or by the oxidation of the substrate at the toe. The weld toe is the point where the deposit meets the substrate, and it is often a region of poor shielding. The solution is to improve the shielding gas coverage and to clean the substrate thoroughly before surfacing.
Lack of fusion between layers is caused by insufficient heat input in the subsequent pass. If the laser power is too low, the new layer does not melt the previous layer, and a cold lap forms. This is a serious defect because it creates a discontinuity that can propagate under load.
Defect Analysis: Cracks, Porosity, and Lack of Fusion
The paper identifies the three main defects in multi-layer nickel-based alloy surfacing. Table 2 provides a detailed analysis.
| Defect | Root Cause | Mitigation Strategy |
|---|---|---|
| Transverse cracks | Accumulated residual stress; high thermal gradient | Preheat substrate; control interpass temperature; reduce heat input |
| Porosity at weld toe | Gas entrapment; oxidation of substrate | Improve shielding; clean substrate; use a trailing shield |
| Lack of fusion between layers | Insufficient heat input; cold lap | Increase laser power; ensure overlap between passes; monitor melt pool |
The paper also notes that in large-area surfacing, the weld toe may not overlap due to selective wetting. This is a phenomenon where the molten metal does not spread evenly across the substrate, leaving gaps at the toe of the deposit. The cause is the difference in surface tension between the molten metal and the substrate. The solution is to control the line energy and to ensure that the substrate is at the correct temperature.
Composite Layers with Ni-Coated WC
The paper introduces an interesting approach: adding nickel-coated WC particles to the nickel-based alloy powder. The nickel coating improves the wetting between the WC and the nickel matrix, preventing the WC particles from being rejected by the molten pool. The result is a composite layer with higher hardness and no defects.
The key is to control the amount of WC added. Too much WC leads to agglomeration and porosity. Too little WC does not improve the hardness significantly. The paper suggests that a controlled amount of nickel-coated WC can produce a defect-free composite layer with higher hardness.
From a practical standpoint, this is a valuable technique for producing wear-resistant surfaces on components that also require corrosion resistance. The nickel matrix provides corrosion resistance, while the WC particles provide wear resistance. The nickel coating on the WC ensures that the particles are wetted by the molten nickel, creating a strong bond.
Quality Control Approach
The paper's findings can be integrated into a quality control approach based on the PDCA cycle. The plan phase involves defining the process parameters: pre-coat width, thickness, laser power, scanning speed, and powder feed rate. The do phase involves executing the surfacing with careful control of the pre-coat application and the laser parameters. The check phase involves inspecting the deposit for cracks, porosity, and lack of fusion, using visual inspection, dye penetrant testing, and metallographic examination. The act phase involves adjusting the parameters based on the inspection results.
The critical parameters to monitor are the pre-coat width and thickness, the laser power, and the interpass temperature. A simple rule is to keep the pre-coat width at 80% of the beam diameter and the pre-coat thickness at 50-70% of the desired deposit thickness. The laser power should be adjusted to achieve a dilution rate of 5-15%, which ensures good bonding without excessive dilution.
Conclusion
The paper provides a comprehensive analysis of the factors that affect the quality of nickel-based alloy laser powder surfacing. The pre-coat geometry is the most critical parameter, and it must be controlled within a narrow window. Multi-layer and multi-pass techniques are necessary for thick deposits, but they introduce the risk of transverse cracks, porosity, and lack of fusion. The addition of nickel-coated WC particles is a promising approach for producing composite layers with higher hardness and no defects. For the practicing engineer, the paper is a valuable reference for setting up a laser powder surfacing operation, but the process must be controlled with the same discipline as any critical welding operation. The defects are predictable, and they can be prevented with proper process control and inspection.
Zhuojin Pipe Fitting Co., Ltd