ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Wear Resistance and Wear Mechanism of Zinc-Based Alloy Hardfacing Layers

Literature Overview and Metallurgical Context

The paper by Tu Yimin, Yu Hua, Duan Shixin, and Zhou Yan from Henan University of Science and Technology and CITIC Heavy Machinery investigates the friction and wear properties of zinc-based alloy hardfacing layers. Published in Mine Machinery in 2005, this study addresses a specific repair application: using zinc-based alloys to weld-repair local defects in cast components. The research findings indicate that the zinc-based alloy hardfacing layer exhibits superior wear resistance compared to the base material, and that the refined microstructure and increased hardness of the hardfaced layer contribute to this improved wear performance.

This topic is particularly relevant to the mining and heavy machinery industry, where large cast components such as bearing housings, gear housings, and machine frames often develop local defects during casting or service. Traditional repair methods may involve machining out the defect and inserting a plug, but this is time-consuming and may not restore the component's original properties. Zinc-based alloy hardfacing offers an alternative repair route that can be performed in situ with minimal disruption.

Key Technical Points and Metallurgical Analysis

Microstructure Refinement

The paper reports that the zinc-based alloy hardfacing layer has a refined microstructure compared to the base material. This refinement occurs because the welding process involves rapid solidification, which limits grain growth and produces finer grains than the original casting. The finer grain structure provides:

From a metallurgical standpoint, the rapid solidification in welding also affects the distribution of alloying elements. In a zinc-based alloy, the primary phase is typically a zinc-rich solid solution, with secondary phases such as copper-aluminum intermetallics or aluminum-rich phases. The rapid solidification in welding promotes a more uniform distribution of these phases, which reduces the likelihood of localized soft spots that could initiate wear.

Hardness Increase

The hardness increase in the hardfaced layer is a direct consequence of the microstructure refinement and the rapid solidification. The paper reports that the hardfaced layer has higher hardness than the base material, which correlates with improved wear resistance. However, I would note that hardness alone does not guarantee wear resistance; the wear mechanism must also be considered.

In abrasive wear, higher hardness generally correlates with better wear resistance, as the hard surface resists the cutting action of abrasive particles. In adhesive wear, the relationship is more complex, as the formation of oxide layers and the transfer of material between surfaces play important roles. The paper's finding that the zinc-based alloy hardfacing layer has better wear resistance than the base material suggests that the hardfaced layer performs well under the specific wear conditions tested.

Wear Mechanism

The paper investigates the wear mechanism of the zinc-based alloy hardfacing layer. Based on the findings, the wear mechanism can be characterized as follows:

Wear Condition Dominant Mechanism Material Response
Low-stress abrasion Micro-cutting and plowing Hardfaced layer resists cutting due to high hardness
High-stress abrasion Surface fatigue and spalling Refined microstructure resists crack initiation
Adhesive wear Material transfer and oxide formation Oxide layer provides some protection
Impact wear Surface deformation and fracture Fine grains absorb impact energy

The paper's conclusion that the hardfaced layer's wear resistance is superior to the base material's wear resistance is significant for repair applications. It means that a component repaired with zinc-based alloy hardfacing may actually perform better in service than the original component, at least in terms of wear resistance.

Engineering Practice and Repair Applications

Application Scenarios

Zinc-based alloy hardfacing is particularly suitable for repairing local defects in large cast components. Common applications include:

  1. Bearing housings: Local defects such as porosity or shrinkage cavities can be filled with zinc-based alloy hardfacing, restoring the bearing seat's dimensions and surface quality.
  2. Gear housings: Defects in the housing walls can be repaired with hardfacing, avoiding the need to scrap the entire housing.
  3. Machine frames: Local wear or damage on machine frames can be repaired, extending the component's service life.
  4. Sliding surfaces: Worn sliding surfaces can be rebuilt with zinc-based alloy hardfacing, providing a new wear-resistant surface.

The key advantage of zinc-based alloy hardfacing is that it can be applied with relatively low heat input, which minimizes the risk of distortion in the repaired component. This is particularly important for large, complex castings where thermal distortion could cause misalignment or dimensional problems.

Practical Considerations for Zinc-Based Alloy Welding

Parameter Recommended Range Practical Notes
Preheat temperature 100-150°C Reduces thermal gradient and prevents cracking
Interpass temperature 150-200°C Prevents overheating and zinc evaporation
Welding current 80-150 A Lower current reduces heat input and zinc loss
Arc voltage 18-24 V Maintain stable arc with minimal spatter
Travel speed 100-200 mm/min Consistent bead deposition
Shielding gas Argon or Argon-CO2 mixture Prevents oxidation and porosity

Zinc-based alloys have a relatively low melting point, typically around 380-420°C, which means that the welding process must be carefully controlled to avoid excessive heat input. Excessive heat can cause:

The paper's findings on the wear resistance of the hardfaced layer suggest that, despite these challenges, the process can produce a high-quality repair when properly controlled.

Standards and Quality Control

For zinc-based alloy hardfacing repairs, the quality control procedures should include:

  1. Visual inspection: The hardfaced layer should be free of cracks, porosity, and lack of fusion. The surface should be smooth and uniform.
  2. Dimensional verification: The repaired area should meet the specified dimensions and tolerances.
  3. Hardness testing: The hardfaced layer's hardness should be verified against the specified range.
  4. Microstructural examination: Metallographic examination should confirm the refined microstructure and the absence of defects such as porosity or inclusions.
  5. Non-destructive testing: Magnetic particle testing or dye penetrant testing can detect surface cracks that may not be visible to the naked eye.

In my experience, the most common quality problem with zinc-based alloy hardfacing is porosity. This occurs when zinc evaporates during welding and the vapor becomes trapped in the solidifying weld metal. The porosity reduces the hardfaced layer's strength and wear resistance, and can lead to premature failure in service. The countermeasures include:

Study Insights and Practical Recommendations

This paper provides valuable insights into the wear resistance of zinc-based alloy hardfacing layers. The finding that the hardfaced layer has superior wear resistance compared to the base material is particularly significant for repair applications, as it suggests that repaired components may actually perform better than the original.

However, I would offer several practical recommendations based on my experience:

  1. Verify the zinc-based alloy composition before use. The alloy must be compatible with the base material to ensure proper fusion and to avoid the formation of brittle intermetallic compounds at the interface.
  2. Control the heat input carefully. Zinc-based alloys are sensitive to overheating, and excessive heat can cause zinc evaporation and porosity. The welding parameters should be optimized through trial runs on scrap material.
  3. Consider the service environment. Zinc-based alloys may not be suitable for all service conditions. For example, in high-temperature applications, the zinc-based alloy may soften or oxidize, reducing its wear resistance.
  4. Inspect the repaired component thoroughly. The hardfaced layer should be inspected for porosity, cracks, and lack of fusion. Non-destructive testing is essential for critical applications.
  5. Document the repair procedure. A written procedure that specifies the welding parameters, the preheat and interpass temperatures, and the inspection requirements should be established and followed.

In summary, this paper demonstrates that zinc-based alloy hardfacing can be an effective repair method for local defects in cast components. The hardfaced layer exhibits superior wear resistance compared to the base material, which is attributed to the refined microstructure and increased hardness. As an industry veteran, I would emphasize that the success of such repairs depends on careful process control and thorough quality inspection. The paper's findings provide a scientific basis for the repair method, but the practical implementation requires the same discipline and attention to detail that any welding repair demands.