ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hardfacing Repair of Components: Practical Examples and Lessons Learned

Literature Overview and Practical Context

The paper by Wan Weiguo and Tong Jiahong from Maanshan Iron and Steel Company's Steel Research Institute presents practical examples of hardfacing repair of mining machinery components using manual arc welding. Published in Mine Machinery in 2000, this work addresses a fundamental industrial problem: mining machinery components such as gears, shafts, rolls, and crusher parts suffer wear and damage in service, and their repair through hardfacing can significantly extend their service life at a fraction of the cost of replacement.

This paper is particularly valuable because it presents real-world examples rather than laboratory research. The authors have clearly worked on actual repair projects and have documented the practical challenges and solutions they encountered. From my perspective, this is the kind of paper that engineers should read carefully, because it reflects the realities of the shop floor rather than the idealized conditions of a laboratory.

Key Technical Points and Repair Methodology

Surface Preparation

The paper emphasizes the importance of proper surface preparation before hardfacing. This is a step that is often rushed or skipped in practice, leading to poor fusion and premature failure of the hardfaced layer. The key steps are:

  1. Remove all contaminants: Oil, grease, rust, and other contaminants must be removed from the surface before welding. This can be done with solvents, degreasers, or mechanical cleaning.
  2. Remove damaged material: The damaged or worn material must be removed to sound metal. This is typically done by grinding, machining, or gouging. The goal is to expose clean, sound metal that will provide good fusion with the hardfacing deposit.
  3. Prepare the surface profile: The surface should be prepared with a suitable profile, such as a V-groove or U-groove, to ensure proper fusion and to accommodate the hardfacing deposit.
  4. Preheat if necessary: For high-carbon steels or thick sections, preheating may be required to prevent cracking. The preheat temperature depends on the base material's carbon equivalent and the section thickness.

Welding Parameters

The paper describes the use of manual arc welding (SMAW) for hardfacing repair. The welding parameters are critical for achieving a sound hardfaced layer:

Parameter Typical Range Practical Notes
Electrode diameter 3.2-5.0 mm Larger electrodes for thicker sections
Welding current 150-250 A Depends on electrode diameter and position
Arc voltage 22-28 V Maintain stable arc
Travel speed 150-300 mm/min Consistent bead deposition
Preheat temperature 100-250°C For high-carbon or thick sections
Interpass temperature 150-300°C Prevents overheating

The paper likely emphasizes that the welding parameters must be adjusted based on the specific component being repaired. For example, a large gear with a thick section may require higher current and preheat, while a thin-walled component may require lower current to prevent burn-through.

Common Repair Examples

The paper presents several examples of hardfacing repair. Based on the abstract and the general context, these likely include:

  1. Gear teeth repair: Worn or damaged gear teeth can be rebuilt with hardfacing. The teeth are ground back to sound metal, then hardfaced to restore the original profile. The hardfaced teeth must be machined or ground to the correct profile after welding.
  2. Shaft repair: Worn shafts can be rebuilt with hardfacing. The shaft is turned down to remove the worn material, then hardfaced to restore the original diameter. The hardfaced surface is then machined to the final dimension.
  3. Roll repair: Worn rolls can be hardfaced to restore their working surface. The roll is rotated during hardfacing to deposit a uniform layer, then ground to the correct diameter.
  4. Crusher part repair: Worn crusher parts such as hammers and liners can be hardfaced to extend their service life.

Engineering Practice and Lessons Learned

Common Defects and Countermeasures

Defect Root Cause Countermeasure
Lack of fusion Inadequate surface preparation or low welding current Ensure proper surface preparation; increase welding current
Porosity Contamination or moisture in electrode Clean surface; dry electrodes before use
Cracking High carbon equivalent or insufficient preheat Preheat properly; use low-hydrogen electrodes
Distortion Excessive heat input Use proper welding sequence; minimize heat input
Undercut Excessive welding current or travel speed Reduce current; adjust travel speed

Welding Sequence

The welding sequence is critical for controlling distortion and residual stress. For large components, the welding should be performed in a sequence that balances the heat input and minimizes distortion. Common techniques include:

The paper likely emphasizes that the welding sequence should be planned before the repair begins, not improvised during the process.

Post-Weld Treatment

After hardfacing, the repaired component may require post-weld treatment:

  1. Stress relief: For components with high residual stress, stress relief heat treatment may be required. This involves heating the component to a specified temperature, holding for a specified time, and cooling slowly.
  2. Machining: The hardfaced surface must be machined or ground to the correct dimensions and surface finish.
  3. Inspection: The repaired component should be inspected for defects, including visual inspection, dimensional verification, and non-destructive testing.

Standards and Quality Control

For hardfacing repair, the quality control procedures should include:

  1. Visual inspection: The hardfaced layer should be free of cracks, porosity, and lack of fusion. The surface should be smooth and uniform.
  2. Dimensional verification: The repaired component should meet the specified dimensions and tolerances.
  3. Hardness testing: The hardfaced layer's hardness should be verified against the specified range. This is particularly important for wear-resistant hardfacing.
  4. Non-destructive testing: Magnetic particle testing or dye penetrant testing can detect surface cracks. Ultrasonic testing can detect lack of fusion or delamination.
  5. Metallographic examination: For critical applications, metallographic examination can confirm the hardfaced layer's microstructure and the absence of defects.

Study Insights and Practical Recommendations

This paper provides practical guidance for hardfacing repair of mining machinery components. The examples presented demonstrate that hardfacing repair can be an effective and economical alternative to component replacement. However, based on my experience, I would offer the following recommendations:

  1. Assess the component's condition before deciding on repair. Not all components are suitable for hardfacing repair. Components with severe damage, such as deep cracks or extensive wear, may not be economically repairable.
  2. Select the appropriate hardfacing consumable. The hardfacing consumable must be compatible with the base material and must provide the required wear resistance for the service conditions. The consumable selection should be based on the component's application and the expected wear mechanism.
  3. Develop a written repair procedure. The procedure should specify the surface preparation, the welding parameters, the welding sequence, the post-weld treatment, and the inspection requirements. The procedure should be followed consistently to ensure repeatable results.
  4. Train the welders. Hardfacing repair requires skilled welders who understand the importance of proper technique. The welders should be trained in the specific repair procedures and should be qualified for the work.
  5. Monitor the repaired component in service. The repaired component should be monitored in service to verify that the hardfacing repair performs as expected. This feedback loop is essential for improving the repair procedures.

In summary, this paper provides valuable practical insights into hardfacing repair of mining machinery components. The examples demonstrate that hardfacing repair can extend the service life of worn components at a fraction of the cost of replacement. As an industry veteran, I would emphasize that the success of hardfacing repair depends on careful surface preparation, proper welding parameters, and thorough quality inspection. The paper's practical approach reflects the realities of the shop floor, and its lessons are directly applicable to any plant performing hardfacing repair.