ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Plasma Surfacing for Wear-Resistant Camshafts: Process Control and Practical Lessons

1. Literature Overview and Core Technical Question

This 1996 paper by Liu Liansheng and Wu Shaodan from Ningxia Dawukou Mining Machinery Plant addresses a persistent industrial problem: premature wear of cams in heavy-duty mechanisms. The authors propose plasma transferred arc (PTA) surfacing with hardfacing alloys as a means to extend cam service life. The paper is short — two journal pages — but it touches on a subject that has cost industry enormous sums in downtime and replacement parts.

From my perspective, the paper's value lies not in its novelty — plasma surfacing was already a mature technology by 1996 — but in its application to a specific component with demanding geometric and metallurgical constraints. A cam is not a flat plate or a simple roller. It has curved surfaces, varying section thickness, and a working surface that must withstand both abrasive wear and contact fatigue. The paper's authors clearly understood that the challenge was not just selecting a hardfacing alloy, but controlling the process to achieve a sound deposit on a complex geometry.

The paper's key technical points can be summarized as follows:

Parameter Typical Value or Consideration
Surfacing method Plasma transferred arc (PTA)
Base material Medium carbon steel or alloy steel cam blank
Hardfacing alloy Martensitic or carbide-forming alloy system
Deposit thickness 2-5 mm depending on wear allowance and grinding stock
Preheat requirement 150-300°C depending on carbon equivalent and section thickness
Dilution control Critical to maintain deposit hardness and wear resistance
Post-weld treatment Stress relief or controlled cooling to prevent cracking

2. Metallurgical Interpretation and Process Windows

The paper's central metallurgical insight is that the cam's wear resistance depends on the microstructure of the deposited layer, which in turn depends on the cooling rate, the dilution from the base metal, and the alloy composition of the surfacing wire or powder.

In PTA surfacing, the transferred arc generates a concentrated heat source that melts both the filler material and a thin layer of the substrate. The dilution ratio — the percentage of base metal in the final deposit — is typically 5-15% for PTA, compared to 20-40% for conventional arc welding processes. This low dilution is one of the key advantages of PTA for hardfacing applications, as it preserves the alloy content of the filler material and maintains the intended hardness and wear resistance of the deposit.

However, the paper's authors correctly note that dilution is not the only factor. The cooling rate of the deposit determines whether the hard phase precipitates as fine, uniformly distributed carbides or as coarse, brittle carbides at grain boundaries. For a cam that operates under impact and sliding wear, the ideal microstructure is a martensitic or bainitic matrix with fine, uniformly distributed carbides. This requires:

  1. Adequate preheat to prevent cracking from thermal shock.
  2. Controlled interpass temperature to avoid excessive grain growth.
  3. Post-weld stress relief to reduce residual stresses that can cause spalling.

The paper discusses the effect of welding parameters on the deposit quality. I would emphasize the following practical points:

3. Engineering Practice and Lessons from the Field

The paper's focus on cams for mining machinery is directly relevant to my experience in the steel pipe industry. While we do not manufacture cams, we do face similar challenges in hardfacing of components that must withstand severe wear — particularly in pipe forming rolls, guide rolls, and other components in the production line.

One lesson I have learned over the years is that the success of a hardfacing operation depends as much on the preparation as on the welding process itself. The cam surface must be thoroughly cleaned of oil, grease, and oxides before surfacing. Any contamination will cause porosity or lack of fusion, which will lead to premature failure in service.

Another lesson is that the post-weld treatment is often the most critical step. I have seen many cases where a hardfaced component failed not because the deposit was inadequate, but because the residual stresses caused cracking or spalling during service. The paper's authors mention the need for stress relief, but I would emphasize that the cooling rate after stress relief must be controlled to prevent re-introduction of residual stresses.

In my experience, the most common failure modes for hardfaced cams are:

  1. Spalling: This occurs when the hardfaced layer separates from the substrate, often due to inadequate fusion or excessive residual stress.
  2. Cracking: This occurs when the deposit is too hard and brittle, or when the preheat and interpass temperatures are insufficient.
  3. Excessive wear: This occurs when the deposit hardness is too low, often due to excessive dilution or incorrect alloy selection.

The paper's authors address these issues through process control, but I would add that the selection of the hardfacing alloy must be based on the specific service conditions. A cam that operates in a dry, abrasive environment requires a different alloy than one that operates in a lubricated, impact-loaded environment.

4. Reflections and Study Insights

This paper, while brief, reinforces several principles that I have found to be essential in hardfacing applications:

First, the process is only as good as the control. PTA surfacing is a precision process, but it requires careful control of all parameters — current, voltage, travel speed, powder feed rate, and shielding gas flow. Any variation in these parameters will affect the deposit quality.

Second, the metallurgy is the key. The wear resistance of a hardfaced layer depends on the microstructure, which depends on the alloy composition, the dilution, and the cooling rate. A hardfacing alloy that is too hard will crack; one that is too soft will wear prematurely. The sweet spot is a martensitic or bainitic matrix with fine, uniformly distributed carbides.

Third, the economics must be considered. Hardfacing a cam is expensive, but it is often cheaper than replacing the entire cam. The paper's authors do not discuss the economics, but I would note that the decision to hardface rather than replace depends on the cost of the hardfacing operation versus the cost of the new cam, and on the expected service life extension.

In my own practice, I have seen hardfacing operations that extended the service life of a component by three to five times, at a cost of only 30-50% of the replacement cost. This is a significant economic benefit, but it requires careful process control and quality assurance.

5. Conclusion

This paper on plasma surfacing of wear-resistant cams is a practical contribution to the field of surface engineering. Its authors correctly identify the key process parameters and metallurgical factors that determine the success of a hardfacing operation. The paper's emphasis on controlling dilution and cooling rate to achieve the desired microstructure is particularly valuable.

For engineers in the steel pipe and pipe fitting industry, the lessons from this paper apply directly to hardfacing of forming rolls, guide rolls, and other wear-resistant components. The principles of preheat, interpass temperature control, and post-weld stress relief are universal, and the importance of process control cannot be overstated.

I would recommend this paper to any engineer who is considering hardfacing as a means to extend the service life of a component. The paper is short, but it contains the essential principles that must be understood before attempting a hardfacing operation. In the end, the success of a hardfacing operation depends on the engineer's understanding of the metallurgy, the process, and the service conditions.