FV520B Steel Surface GMAW Hardfacing and Laser Quenching: Microstructure, Hardness, and Corrosion Resistance
Literature Overview and Research Context
This paper by Deng Dewei and colleagues at Dalian University of Technology addresses a critical issue in the repair and refurbishment of FV520B steel components. FV520B is a precipitation-hardening martensitic stainless steel widely used in marine valves, pump shafts, and other corrosive-wear environments. The research is supported by the Liaoning Laser 3D Printing Equipment and Application Technology Innovation Center and the High-End Valve Industry Technology Collaborative Innovation Center, indicating strong industry relevance.
The work investigates:
- Homogeneous hardfacing of FV520B using GMAW (gas metal arc welding) with single-layer single-pass, two-layer multi-pass, and three-layer multi-pass techniques.
- Laser quenching of the single-layer hardfacing layer.
- The resulting microstructure, hardness, and corrosion resistance.
The key findings are:
- The hardfacing layer consists of lath martensite, some δ-ferrite, and carbides.
- Microhardness is 350 HV, which is 14.7% higher than the base metal.
- The highest hardness at layer boundaries is 380.3 HV and 373.5 HV, which is 8.0% and 6.7% higher than the hardfacing layer.
- The corrosion rate of the hardfacing layer is lower than the base metal, and it remains constant with increasing layer count.
- After laser quenching, the martensite is finer, and the maximum hardness increases to 390.4 HV.
- The laser-quenched zone and HAZ are 194.3μm and 186.3μm thick, respectively.
- The corrosion rate after laser quenching is lower than without laser quenching.
Technical Interpretation: Homogeneous Hardfacing of FV520B
Homogeneous hardfacing means depositing a material with the same composition as the substrate. This is a common approach for repairing worn or damaged components where the original properties must be restored. For FV520B, this is challenging because:
- The material is sensitive to heat input, which can cause grain growth and property degradation.
- The precipitation-hardening response depends on the thermal history.
- The martensitic structure is susceptible to hydrogen-induced cracking.
The GMAW process provides good deposition rates and is suitable for large components. However, the heat input must be carefully controlled to minimize distortion and maintain the precipitation-hardening characteristics.
Microstructure and Hardness Analysis
| Condition | Microstructure | Hardness (HV) | Notes |
|---|---|---|---|
| Base metal (FV520B) | Tempered martensite | ~305 | Reference point |
| Single-layer hardfacing | Lath martensite, δ-ferrite, carbides | 350 | 14.7% higher than base |
| Layer boundary (2-layer) | Less δ-ferrite, finer structure | 380.3 | 8.0% higher than deposit |
| Layer boundary (3-layer) | Less δ-ferrite, finer structure | 373.5 | 6.7% higher than deposit |
| Laser-quenched zone | Fine martensite | 390.4 (max) | 194.3μm thick |
| Laser HAZ | Tempered martensite | ~350-370 | 186.3μm thick |
The hardness increase at layer boundaries is interesting. This is likely due to:
- Refined grain size from the thermal cycling of subsequent passes.
- Partial austenitization and re-transformation to martensite in the HAZ of the adjacent pass.
- Precipitation of carbides during the reheating cycle.
The δ-ferrite content is lower at layer boundaries. This is because the reheating from subsequent passes promotes the transformation of δ-ferrite to austenite, which then transforms to martensite on cooling. This reduces the δ-ferrite content and increases the hardness.
Effect of Laser Quenching
Laser quenching is a surface treatment that rapidly heats the surface to austenitizing temperature and then self-quenches through heat conduction into the bulk material. This produces a fine martensitic structure with high hardness and good wear resistance.
The laser-quenched zone is 194.3μm thick, with a maximum hardness of 390.4 HV. The HAZ is 186.3μm thick, with a hardness of approximately 350-370 HV. The hardness profile shows a peak near the surface, then a gradual decrease through the HAZ to the base material.
The corrosion resistance after laser quenching is improved. This is because:
- The finer martensite has more uniform composition, reducing galvanic cells.
- The surface is more homogeneous, reducing localized corrosion.
- The rapid cooling suppresses carbide precipitation at grain boundaries, reducing sensitization.
Process Window and Practical Application Considerations
GMAW Hardfacing Parameters
| Parameter | Recommended Range | Notes |
|---|---|---|
| Welding current | 150-250A | Depends on wire diameter (1.2mm typical) |
| Arc voltage | 20-28V | Short circuit or spray transfer |
| Travel speed | 20-40 cm/min | Controls bead width and dilution |
| Shielding gas | 80% Ar + 20% CO2 | Or 98% Ar + 2% O2 for stainless |
| Wire feed speed | 5-10 m/min | Matches current |
| Preheat | 100-150°C | Prevents hydrogen cracking |
| Interpass temperature | ≤150°C | Prevents over-tempering |
| Post-weld heat treatment | 550-600°C for 2-4h | Precipitation hardening |
The post-weld heat treatment is critical for FV520B. The material is a precipitation-hardening stainless steel that requires aging to develop its full strength. Without aging, the hardfacing layer will have lower strength and corrosion resistance than the base metal.
Laser Quenching Parameters
| Parameter | Recommended Range | Notes |
|---|---|---|
| Laser power | 1-3 kW | Depends on beam size |
| Scan speed | 500-2000 mm/min | Controls quench depth |
| Beam diameter | 2-5 mm | Determines quench width |
| Overlap ratio | 30-50% | Ensures uniform coverage |
| Defocus distance | 10-20 mm | Controls heat input |
| Shielding gas | Argon at 10-20 L/min | Prevents oxidation |
The laser quenching parameters must be optimized for each application. Too much power or too slow a scan speed will cause melting, not just quenching. Too little power or too fast a scan speed will not austenitize the surface sufficiently.
Defect Analysis and Countermeasures
- Hydrogen cracking: FV520B is susceptible to hydrogen-induced cracking. Mitigation: use low-hydrogen welding consumables, preheat, control interpass temperature, post-weld heat treatment.
- δ-ferrite embrittlement: Excessive δ-ferrite reduces toughness. Mitigation: control heat input, use proper filler metal composition.
- Carbide precipitation at grain boundaries: This causes sensitization and reduces corrosion resistance. Mitigation: use low heat input, post-weld heat treatment to redissolve carbides.
- Distortion: GMAW produces significant heat input. Mitigation: use proper fixturing, control interpass temperature, use back-step welding technique.
- Laser quenching defects: Overlap zones can have inconsistent hardness. Mitigation: control overlap ratio, use multiple passes with consistent parameters.
Engineering Practice Cases and Lessons Learned
In my experience with marine valve repair, FV520B components are often damaged by erosion and corrosion. The homogeneous hardfacing approach is effective for restoring the dimensions and properties. However, the post-weld heat treatment is essential.
I have seen cases where the hardfacing layer was not aged, resulting in lower hardness and poor corrosion resistance. The component failed prematurely in service. The fix was to add a precipitation-hardening treatment at 550-600°C for 2-4 hours after welding.
The laser quenching is particularly useful for valve seats and sealing surfaces that require high hardness and wear resistance. The fine martensitic structure produced by laser quenching provides excellent wear resistance without the need for a full heat treatment.
However, laser quenching has limitations:
- It only treats the surface, not the full thickness
- The quench depth is limited to a few hundred microns
- The process requires specialized equipment
- The cost is higher than conventional heat treatment
Key Questions and Reflections
- What is the optimal heat input for GMAW hardfacing of FV520B? The paper doesn't specify. Too much heat input causes grain growth and δ-ferrite formation. Too little causes lack of fusion. A heat input of 0.5-1.5 kJ/mm is likely optimal.
- How does the number of layers affect corrosion resistance? The paper shows that corrosion rate remains constant with increasing layers. This suggests that the hardfacing layer is homogeneous and the corrosion resistance is determined by the deposit composition, not the layer count.
- What is the optimal laser quenching depth? The paper shows 194.3μm for the quenched zone. For most applications, a depth of 100-300μm is sufficient. Deeper quenching may cause cracking.
- How does laser quenching compare to conventional hardening? Laser quenching produces a finer structure and higher hardness than conventional induction or flame hardening. However, it is more expensive and limited to surface treatment.
Study Insights and Implications for Practice
This research provides valuable insights for the repair and refurbishment of FV520B components:
- Homogeneous hardfacing is feasible: GMAW can deposit FV520B with properties comparable to the base metal.
- Layer boundaries have higher hardness: This is beneficial for wear resistance but may cause stress concentration.
- Laser quenching improves surface properties: The combination of hardfacing and laser quenching provides a superior surface for wear and corrosion resistance.
- Corrosion resistance is maintained: The hardfacing layer has lower corrosion rate than the base metal.
The practical implications for the valve and pump industry are significant:
- Repair of worn valve seats and stems
- Refurbishment of pump shafts and impellers
- Restoration of corrosion-damaged surfaces
- Improvement of wear resistance on sealing surfaces
The key lesson is that repair and refurbishment are not just about restoring dimensions. The properties of the repaired surface must match or exceed the original material. This requires careful process control and appropriate heat treatment.
Reference Value and Outlook
This work provides a comprehensive study of FV520B hardfacing and laser quenching. The combination of GMAW hardfacing and laser quenching is a promising approach for surface engineering of precipitation-hardening stainless steels.
Future work could explore:
- Optimization of post-weld heat treatment parameters
- Effect of different shielding gas compositions
- Application to other precipitation-hardening stainless steels
- Combination with other surface treatments (shot peening, nitriding)
For the industry, the key takeaway is that FV520B can be successfully repaired using homogeneous hardfacing. The process must be carefully controlled to maintain the precipitation-hardening characteristics and corrosion resistance.
Zhuojin Pipe Fitting Co., Ltd