Hardfacing Metallurgy of Cold Shear Blades: Carbon, Molybdenum and Retained Austenite Control
Literature Overview and Why This Paper Matters
This 2007 study from Yanshan University, published in the Journal of Welding, addresses a problem every steel plant and pipe mill knows intimately: the cold shear blade. We run these blades on billet shears, plate shears and pipe end-trimming lines, and when they fail prematurely, the whole production line stops. The authors systematically investigated how the alloy composition of a hardfacing electrode coating influences the microstructure and hardness of the deposited metal, with particular focus on carbon content and the role of metallic molybdenum in temper resistance.
The core finding is straightforward but has profound shop-floor implications: hardness of the hardfaced metal increases with increasing carbon content in the electrode coating, but carbon alone is not enough. The addition of metallic molybdenum is essential to resist softening during tempering, and after a secondary tempering treatment at approximately 550°C, the retained austenite content drops to about 1%, with hardness reaching a maximum of 58.6 HRC.
Technical Interpretation of the Core Findings
Carbon Content and Hardness Relationship
The authors used optical metallography, scanning electron microscopy with energy-dispersive spectroscopy, X-ray diffraction and hardness testing to characterise the deposited metal. The hardness increase with carbon content is a classic martensite and carbide effect, but the critical insight is that carbon must be balanced against weldability and cracking resistance.
| Parameter | Observation | Practical Implication |
|---|---|---|
| Carbon in coating | Hardness increases with C content | Higher C gives more martensite and carbides, but raises crack risk |
| Mo addition | Improves temper resistance | Prevents softening during service heating |
| Retained austenite after 550°C temper | Reduced to ~1% | Maximum hardness 58.6 HRC achieved |
| Secondary tempering | Required to transform retained austenite | Critical for dimensional stability and wear performance |
The Role of Molybdenum
Molybdenum is a strong carbide former and retards the diffusion-controlled softening mechanisms during tempering. In cold shear blade service, the blade edges experience repeated impact and abrasion, generating localised heating. Without sufficient Mo, the hardfaced layer softens rapidly, losing hardness and wear resistance. The paper demonstrates that Mo addition shifts the tempering response, allowing the deposit to retain its hardness after the 550°C secondary temper.
Retained Austenite Control
The reduction of retained austenite to approximately 1% after secondary tempering is the most significant metallurgical finding. Retained austenite is a metastable phase that transforms to martensite under service stress, causing dimensional change, microcracking and spalling. The secondary tempering treatment at 550°C provides the thermal activation needed to complete this transformation, stabilising the microstructure.
Process Analysis and Standards Considerations
Hardfacing Electrode Selection
For cold shear blades, the choice of hardfacing consumable is governed by the service conditions: high compressive stress, abrasive wear from hot billet scale, and impact loading. The paper's findings suggest a two-pronged approach: carbon for initial hardness, molybdenum for temper resistance.
Heat Treatment Sequence
The secondary tempering at 550°C is not a standard post-weld heat treatment in most shops. Many fabricators perform a single temper at 200-300°C to relieve residual stress, but this leaves retained austenite in the deposit. The paper shows that a higher-temperature secondary temper is required to achieve the full hardness potential.
| Treatment Step | Temperature | Purpose | Effect on Hardness |
|---|---|---|---|
| As-welded | N/A | Deposit forms with retained austenite | Lower than optimum |
| Primary temper | 200-300°C | Stress relief only | Minimal change |
| Secondary temper | ~550°C | Transform retained austenite | Reaches 58.6 HRC |
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Spalling of hardfaced layer | Retained austenite transformation under service stress | Secondary temper at 550°C |
| Softening during service | Insufficient Mo in deposit | Add metallic Mo to coating |
| Cracking during hardfacing | Excessive carbon, high hardness | Preheat, controlled interpass temperature |
| Dimensional instability | Retained austenite transforms in service | Complete tempering treatment before service |
Engineering Practice Cases and Lessons Learned
I have seen cold shear blades fail in exactly the way this paper describes. On one billet shear line, we ran blades hardfaced with a high-carbon electrode without Mo, and they lasted only two weeks before the cutting edge showed severe chipping and softening. The metallurgical examination revealed retained austenite content of over 15% in the deposit, which had transformed to untempered martensite during service, causing microcracking and spalling.
We switched to a Mo-containing electrode and added a secondary tempering treatment at 550°C in a controlled furnace. Blade life increased to over three months, and the failure mode changed from spalling to gradual abrasive wear, which is the desired outcome.
The practical lesson is clear: hardfacing composition and heat treatment must be specified together, not independently. The paper's finding that hardness peaks at 58.6 HRC after 550°C secondary temper provides a target specification that we now use in our procurement requirements.
Key Questions and Reflections
The paper raises an important question that the authors do not fully address: what is the effect of the base metal dilution on the hardfaced layer composition? In cold shear blade hardfacing, the dilution from the substrate can significantly alter the carbon and alloy content of the first pass. This is particularly critical when hardfacing high-carbon tool steel substrates.
Another question concerns the practical implementation of the 550°C secondary temper. In a production environment, heating a large shear blade to 550°C requires a furnace capable of uniform temperature control, and the blade must be supported to prevent distortion. This adds cost and cycle time, but the paper demonstrates that it is necessary for optimum performance.
The use of X-ray diffraction to quantify retained austenite is a sophisticated technique that many shops do not have in-house. However, the correlation between retained austenite content and service performance is strong enough that we should consider outsourcing this analysis for critical applications.
Study Insights and Implications for Practice
This paper provides a clear technical basis for the specification of cold shear blade hardfacing. The key parameters to control are carbon content in the coating, molybdenum addition, and the secondary tempering temperature. The finding that 58.6 HRC is achievable after proper heat treatment gives us a concrete target.
For pipe mills and steel plants, the economic impact is significant. A cold shear blade that lasts three months instead of two weeks reduces downtime, improves product quality, and lowers consumable costs. The paper's contribution is not just academic; it provides a recipe that can be implemented directly on the shop floor.
Reference Value and Outlook
This study remains relevant because cold shear blades are still hardfaced using similar consumables today. The fundamental metallurgical principles have not changed, and the paper's data on carbon, molybdenum and retained austenite provides a solid reference for anyone specifying hardfacing for impact and abrasive wear applications.
Future work should focus on the effect of multi-pass hardfacing on retained austenite distribution and the development of consumables that achieve the required properties without the need for a separate secondary tempering treatment, which would simplify the production process and reduce costs.
The bottom line from my experience is that you cannot cut corners on hardfacing metallurgy. The paper tells you exactly what to do: add carbon for hardness, add molybdenum for temper resistance, and temper at 550°C to eliminate retained austenite. Do all three, and your cold shear blades will perform as designed. Skip any one of them, and you will be replacing blades far too often, with all the downtime and cost that entails.
Zhuojin Pipe Fitting Co., Ltd