ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Low-Frequency Magnetic Field on Microstructure and Wear Resistance of Submerged Arc Hardfacing Layers

Literature Overview and Core Findings

The paper by Chang Yunlong, Li Jingya, Yang Dianchen, and Jin Wei from Shenyang University of Technology addresses a topic that is not as widely discussed as it should be: the use of external magnetic fields to control the solidification of weld metal. The authors applied a low-frequency longitudinal magnetic field during submerged arc hardfacing and studied its effect on weld bead geometry, hardness, wear resistance, and microstructure. The results are remarkable: the grain size decreased from 25.6 μm to 10.6 μm, the hardness increased from 50.5 HRC to 55.0 HRC, and the wear loss decreased from 0.035 g to 0.015 g. The weld width increased, while the penetration depth slightly decreased.

The mechanism is attributed to the electromagnetic stirring effect of the magnetic field, which breaks up the growing dendrites, promotes nucleation, and refines the grain structure. The finer grains lead to higher hardness and better wear resistance, which is consistent with the Hall-Petch relationship.

Technical Interpretation and Process Considerations

Electromagnetic Stirring Mechanism

The application of a longitudinal magnetic field during arc welding creates a Lorentz force in the molten pool, which causes the liquid metal to rotate. This stirring action has two primary effects. First, it breaks up the dendrites that form at the solidification front, creating more nucleation sites. Second, it homogenizes the temperature and composition of the molten pool, reducing segregation. The result is a finer, more uniform grain structure. The authors found that the grain size was reduced by more than 50%, which is a significant improvement.

Effect on Weld Bead Geometry

The authors observed that the weld width increased and the penetration depth slightly decreased when the magnetic field was applied. This is a practical consideration. A wider weld bead means more dilution with the substrate, which can be beneficial or detrimental depending on the application. For hardfacing, a wider bead with less penetration is often desirable because it reduces dilution and increases the deposition rate. However, it also means the heat input is spread over a larger area, which can affect the HAZ.

Quantitative Results Summary

Parameter Without Magnetic Field With Low-Frequency Magnetic Field
Grain Size (μm) 25.6 10.6
Hardness (HRC) 50.5 55.0
Wear Loss (g) 0.035 0.015
Weld Width Baseline Increased
Penetration Depth Baseline Slightly decreased

Practical Implications and Lessons Learned

Where This Fits in Real Manufacturing

Submerged arc hardfacing is widely used for large components such as rolls, mill housings, and crusher parts. The application of a magnetic field is not a common practice in most shops, but the results suggest it should be. The 43% reduction in wear loss is significant, and the hardness increase from 50.5 to 55.0 HRC is substantial. For a roll that is expected to last a certain number of tonnes of steel, this could translate to a 20-30% increase in service life.

Quality Control and Acceptance Criteria

When I specify hardfacing with magnetic field assistance, I demand the following:

  1. Metallographic examination to verify grain refinement, with a target grain size below 15 μm.
  2. Hardness testing across the hardfacing layer, with a minimum of 53 HRC.
  3. Wear testing on a sacrificial coupon, with a maximum wear loss of 0.020 g under the specified test conditions.
  4. Weld bead geometry measurement to ensure the width-to-penetration ratio is within the specified range.

Common Defects and Countermeasures

Defect Root Cause Countermeasure
Excessive grain growth Insufficient magnetic field strength Increase field strength or frequency
Porosity Gas entrapment in the molten pool Adjust shielding gas flow, reduce travel speed
Lack of fusion Low heat input, excessive magnetic stirring Reduce field strength, increase current
Segregation Insufficient stirring Increase field strength, optimize frequency

Key Questions and Reflections

The paper is well-executed, but I would like to see more data on the effect of frequency. The authors used a "low-frequency" magnetic field, but they do not specify the exact frequency range. In my experience, frequencies between 5 Hz and 50 Hz are most effective for grain refinement. I would also like to know the magnetic field strength, which is typically expressed in millitesla (mT). Without this data, it is difficult to replicate the results on a different setup.

Study Insights and Implications

This paper is a reminder that we should not be satisfied with the status quo. For decades, we have been hardfacing rolls and crusher parts without any external assistance, and we have accepted the grain size and wear resistance that we get. The application of a magnetic field is a relatively simple addition to the process, and it can deliver a 43% reduction in wear loss. In a high-volume production environment, this is a significant competitive advantage.

For my team, the takeaway is clear: if you are doing submerged arc hardfacing, you should at least trial the use of a low-frequency magnetic field. The equipment is not expensive, and the potential benefits are substantial. The key is to optimize the field strength and frequency for your specific application, and to verify the results with metallography and wear testing.

Reference Value and Outlook

This study is a valuable contribution to the field of hardfacing and surface engineering. It provides quantitative data on the benefits of magnetic field-assisted welding, and it offers a clear mechanism for the grain refinement. The practical value lies in the demonstration that a simple process modification can deliver a significant improvement in wear resistance. Looking ahead, I would like to see more research on the effect of magnetic field on the microstructure of specific hardfacing alloys, and on the long-term performance of magnetic field-assisted hardfacings in industrial service.

The bottom line is this: magnetic field-assisted welding is not a gimmick. It is a proven technique that can refine grain size, increase hardness, and reduce wear. If you are not using it, you are leaving performance on the table. Trial it, optimize it, and verify it. That is how you stay ahead in the hardfacing business.