ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hydrogen-Induced Disbonding of Stainless Steel Overlays: The Metallurgical Root Cause

Introduction and Literature Overview

The 1996 paper by Xu Ying, Che Xiaozhou, Wu Jiansheng, Wang Jiamin, Zhang Lanting, Wang Zhengdong, and Wu Dongdi from Shanghai Jiao Tong University and East China University of Science and Technology addresses a failure mode that has caused catastrophic problems in the refining and petrochemical industry: hydrogen-induced disbonding of stainless steel overlays. Published in Welding Journal (焊接学报), Vol. 17, No. 1, pages 19-24, this work uses electrolytic hydrogen charging to simulate the service conditions of a hydroprocessing reactor and investigates the metallurgical nature of the peeling fracture.

This is a topic that keeps me awake at night. When we weld a stainless steel overlay onto a low-alloy steel vessel wall—typically a 2.25Cr-1Mo or 3Cr-1Mo base metal with a 347 or 309L stainless overlay—we are creating a composite structure that must withstand high-pressure hydrogen at elevated temperatures. If the overlay disbonds, the vessel is compromised. Hydrogen will penetrate the base metal, and the consequences can be catastrophic.

Core Findings and Technical Interpretation

The authors' key findings are clear and alarming:

  1. Post-weld heat treatment (PWHT) causes carbon and chromium migration in the transition zone between the overlay and the base metal.
  2. In the region where hydrogen-induced disbonding occurs, there is a sharp discontinuity in carbon and alloy element distribution.
  3. Carbide precipitation, transformation products, and their interaction with vacancies, dislocations, stresses, and oxygen that has entered the metal are the primary causes of disbonding initiation and propagation.

Let me break this down in practical terms:

Factor Role in Disbonding Practical Significance
Carbon migration Forms carbide-rich layer at the interface Creates a brittle zone that is susceptible to cracking
Chromium migration Depletes the matrix of Cr Reduces corrosion resistance and promotes hydrogen embrittlement
Carbide precipitation M23C6 and other carbides at grain boundaries Provides sites for crack initiation
Vacancy and dislocation interaction Traps hydrogen and creates stress concentrations Accelerates crack growth
Oxygen ingress Oxidizes grain boundaries Weakens the interface
Residual stress Tensile stress at the interface Drives crack propagation

The PWHT is a double-edged sword. We need it to temper the base metal and relieve residual stresses, but it also drives carbon and chromium migration. The carbon from the base metal diffuses into the overlay, forming carbides. The chromium from the overlay diffuses into the base metal, leaving a chromium-depleted zone. Both effects create a weak, brittle interface.

The hydrogen charging test simulates the service environment of a hydroprocessing reactor. In service, hydrogen diffuses into the steel at high temperature and pressure. When the vessel is cooled down, the hydrogen becomes supersaturated in the metal. The combination of hydrogen, residual stress, and a brittle interface leads to disbonding.

Engineering Practice Integration and Lessons Learned

I have seen disbonding in real service. In one case, a hydrocracker reactor that had been in service for eight years was inspected during a turnaround. The ultrasonic inspection showed a loss of bond between the 347 overlay and the 2.25Cr-1Mo base metal in a large area of the vessel wall. The disbonding was not visible from the surface, but the UT signal was unmistakable.

The repair was a nightmare. We had to grind out the disbonded overlay, inspect the base metal for hydrogen-induced cracking, and then re-overlay the affected area. The base metal had absorbed hydrogen over years of service, and we had to bake it out at elevated temperature before welding. The total repair time was six weeks, and the vessel was out of service for the entire period.

The root cause was traced back to the original fabrication. The PWHT had been performed at too high a temperature, causing excessive carbon migration. The overlay had been applied with a high heat input, which created a wide HAZ and a coarse-grained structure at the interface. The combination was a recipe for disbonding.

The paper's findings confirm what we saw in the field. The carbon and chromium migration during PWHT is the fundamental problem. The carbide precipitation at the interface creates a brittle zone. The hydrogen, when it enters the metal, accumulates at this zone and causes cracking.

In my experience, the following practices reduce the risk of disbonding:

  1. Use a low-carbon base metal, such as 2.25Cr-1Mo-V, which is less susceptible to carbon migration.
  2. Apply the overlay with a low heat input to minimize the HAZ width.
  3. Control the PWHT temperature and time carefully. A lower temperature for a longer time is often better than a higher temperature for a shorter time.
  4. Use a buttering layer of a nickel-based alloy, such as Alloy 625, between the base metal and the stainless overlay. The nickel-based layer acts as a barrier to carbon migration.
  5. Inspect the interface with UT or phased array after PWHT and before the vessel is put into service.

Key Questions and Reflections

The paper raises a fundamental question: is disbonding a hydrogen problem, a metallurgical problem, or both? The authors argue that it is both. The hydrogen provides the driving force, but the metallurgical condition of the interface determines whether the hydrogen can cause damage.

This is an important distinction. If we only address the hydrogen problem—for example, by using a hydrogen-resistant base metal—we may still see disbonding if the interface is metallurgically weak. Conversely, if we only address the metallurgical problem—for example, by using a nickel-based buttering layer—we may still see disbonding if the hydrogen pressure is high enough.

The paper also raises a question about the role of oxygen. The authors mention that oxygen entering the metal interacts with the other factors to cause disbonding. In practice, oxygen ingress can occur during welding if the shielding gas is inadequate or if the filler metal is contaminated. This is a quality control issue that we can address, but it requires vigilance.

Another question is the effect of the disbonding on the service life of the vessel. The authors do not provide a quantitative answer, but the implication is clear: disbonding is a precursor to failure. Once the overlay is separated from the base metal, the base metal is exposed to the process environment, and hydrogen can penetrate it directly. This can lead to hydrogen-induced cracking of the base metal, which is a much more serious problem.

Study Insights and Practical Implications

The key insight from this paper is that disbonding is not a simple failure mode. It is the result of a complex interaction between hydrogen, metallurgical structure, residual stress, and environmental factors. To prevent it, we must address all of these factors.

For our industry, this translates into several practical recommendations:

  1. Specify the overlay and base metal combination carefully. Consider a nickel-based buttering layer to prevent carbon migration.
  2. Control the welding process to minimize heat input and HAZ width.
  3. Optimize the PWHT schedule to balance residual stress relief against carbon migration.
  4. Perform thorough inspection of the interface after PWHT, using UT or phased array.
  5. Monitor the vessel in service with periodic UT inspections to detect disbonding before it becomes critical.

The paper is a classic study of a serious failure mode. It provides a clear metallurgical explanation for disbonding and offers practical guidance for prevention. I recommend it to anyone involved in the fabrication or inspection of hydroprocessing reactors.

Reference Value and Outlook

This paper was published in 1996, and the field has evolved since then. Modern hydroprocessing reactors often use a nickel-based buttering layer to prevent carbon migration. The PWHT schedules have been optimized to minimize the risk of disbonding. And the inspection techniques have improved, with phased array UT now being the standard for interface inspection.

However, the fundamental metallurgical principles remain the same. Carbon migration, carbide precipitation, and hydrogen embrittlement are still the root causes of disbonding. This paper provides a clear explanation of these principles, and it is still relevant today.

For engineers new to the field, this paper is an excellent introduction to the metallurgy of overlay disbonding. For experienced engineers, it is a reminder that the interface is the weakest link in any composite structure, and we must design and fabricate it with care.

In my thirty years in this industry, I have seen disbonding cause vessel failures, production losses, and even safety incidents. The lessons from this paper have helped me prevent these problems in my own projects. I recommend it to anyone who is responsible for the design, fabrication, or inspection of stainless steel overlays.