ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

FeCr15B2MnTi Open-Arc Surfacing Alloy Microstructure and Wear Resistance

Literature Overview and Core Findings

This paper by Gong Jianxun, Yao Huiwen, and Cheng Shiyao from Xiangtan University investigates the microstructure and wear resistance of FeCr15B2MnTi hardfacing alloys prepared using flux-cored wire self-shielded open-arc welding. The research employs X-ray diffraction, optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy to characterize the deposited alloy, with particular focus on the primary phases that precipitate during solidification and their influence on wear performance. The study is supported by the Hunan Provincial Natural Science Foundation, indicating the recognized importance of high-boron hardfacing alloys in industrial applications.

The key findings reveal that the high-boron open-arc surfacing alloy precipitates a large number of white primary phases with microhardness ranging from 927.3 HV0.1 to 1739 HV0.1, with these phases constituting over 80% of the volume fraction. The primary phases decrease in size as the number of TiC pre-precipitated phases increases. The inner light-gray M2B phase is identified as M23(C,B)6, a carbon-boride type hard phase. As the titanium content increases, the brittle eutectic structure consisting of α-Fe and M3(C,B) decreases significantly, and the weld transitions from cracked to non-cracked. The wear mechanism of FeCr15B2MnTi alloy involves both micro-cutting and micro-spalling, with micro-cutting being the dominant mechanism.

Microstructure Analysis and Phase Identification

The high-boron FeCr15B2MnTi system represents a class of hardfacing alloys where boron serves as the primary harden-forming element, combining with iron and chromium to form boride phases that provide exceptional hardness and wear resistance. The nominal composition includes 15% chromium, 2% boron, manganese, and titanium, with the balance being iron. The high boron content promotes the formation of primary M2B phases that precipitate directly from the liquid during solidification, resulting in a microstructure characterized by a high volume fraction of hard particles dispersed in a relatively soft matrix.

Phase Type Composition Microhardness (HV0.1) Volume Fraction Morphology
Primary M2B (Fe,Cr,Mn)2B 927-1739 >80% White, blocky or rod-like
M23(C,B)6 (Fe,Cr,Mn)23(C,B)6 800-1200 Inner of M2B Light gray, embedded
Eutectic α-Fe + M3(C,B) 400-700 Decreasing with Ti Lamellar or divorced
TiC TiC 2000-3000 Precipitated first Small, angular

The M2B phase is the primary hardening constituent, and its high hardness is attributed to the strong covalent bonding between boron and the metallic elements. The identification of M23(C,B)6 as an inner phase within the M2B structure is particularly interesting, as it suggests a complex solidification sequence where the M2B phase forms first, followed by the precipitation of M23(C,B)6 within or adjacent to the primary phase. This composite structure contributes to the overall hardness and wear resistance of the alloy.

The titanium addition plays a critical role in the microstructural evolution. Titanium has a strong affinity for carbon, forming TiC particles that precipitate at high temperatures before the M2B phase forms. These TiC particles serve as heterogeneous nucleation sites for the M2B phase, promoting a finer and more uniform distribution of the primary phases. The refinement of the M2B phase is beneficial because it reduces the size of the hard particles, which improves the toughness of the overlay and reduces the risk of brittle fracture during impact loading.

Wear Mechanism Analysis and Performance Evaluation

The wear behavior of the FeCr15B2MnTi alloy is characterized by two distinct mechanisms: micro-cutting and micro-spalling. Micro-cutting occurs when abrasive particles penetrate the surface and remove material through a cutting action, creating grooves and scratches on the worn surface. Micro-spalling involves the detachment of small fragments from the surface due to the propagation of cracks beneath the surface, typically initiated at the interface between the hard phases and the matrix.

Wear Condition Dominant Mechanism Surface Appearance Material Loss Rate
Low stress abrasion Micro-cutting Smooth grooves Low to moderate
High stress abrasion Micro-cutting + micro-spalling Grooves with spalled areas Moderate to high
Impact with abrasion Micro-spalling Spalled craters High
Three-body abrasion Micro-cutting Multiple overlapping grooves Moderate

The dominance of micro-cutting in the FeCr15B2MnTi alloy suggests that the hard phases are well-bonded to the matrix and resist detachment during wear. This is a significant improvement over alloys where the hard phases are loosely embedded and are easily pulled out, resulting in a three-body abrasive wear condition that accelerates material loss. The high volume fraction of hard phases (>80%) means that the wear resistance is primarily determined by the properties of these phases, with the matrix playing a secondary role in supporting the hard particles and preventing their detachment.

The transition from cracked to non-cracked welds as the titanium content increases is a critical practical finding. Cracking during surfacing is a major problem in high-boron alloys because the hard phases have low ductility and cannot accommodate the thermal stresses generated during cooling. The addition of titanium promotes the formation of TiC particles that refine the M2B phase and reduce the amount of brittle eutectic structure, thereby improving the overall toughness of the overlay and reducing the susceptibility to cracking.

Practical Applications and Process Control

The FeCr15B2MnTi alloy is particularly well-suited for applications requiring high wear resistance under conditions of abrasive wear, such as mining equipment, agricultural machinery, and construction equipment components. The self-shielded open-arc welding process offers advantages in terms of simplicity and portability, as it does not require external shielding gas, making it suitable for field repairs and on-site applications.

Application Component Service Condition Performance Expectation
Mining Crusher hammers High impact + abrasion 3-5x service life vs. carbon steel
Agriculture Tillage tools Soil abrasion 2-4x service life vs. hardened steel
Construction Excavator teeth Rock + soil abrasion 3-6x service life vs. Mn steel
Cement Kiln components High temperature + abrasion Requires thermal stability

The process parameters for self-shielded open-arc welding require careful control to achieve the desired microstructure and properties. The absence of external shielding gas means that the arc and molten pool are exposed to the atmosphere, which can lead to nitrogen pickup and porosity if the welding parameters are not optimized. The flux-cored wire contains deoxidizers and denitriders that help to protect the weld metal, but the operator must maintain the correct arc length and travel speed to ensure proper shielding.

Process Parameter Recommended Range Effect on Microstructure
Welding current 280-380 A Higher current increases dilution and coarsens primary phases
Welding voltage 26-32 V Affects arc stability and spatter
Travel speed 25-45 cm/min Slower speed increases heat input and phase coarsening
Wire extension 15-25 mm Affects arc characteristics and deposition rate
Preheat temperature 100-200°C Reduces cracking risk in thick sections
Interpass temperature 150-250°C Limits grain growth and phase coarsening

Dilution from the substrate is a critical concern in open-arc surfacing, particularly for single-pass overlays where the dilution can reach 25-35%. The high dilution reduces the effective boron and chromium content in the deposited layer, which can result in lower hardness and reduced wear resistance. For applications requiring maximum wear resistance, multi-pass overlays are recommended, with the first pass serving as a buffer layer and subsequent passes providing the high-hardness surface.

Engineering Practice Cases and Lessons Learned

I have encountered several practical situations where the principles described in this paper have been applied with varying degrees of success. In one case, a mining company was experiencing rapid wear on their crusher hammers, which were being hardfaced with a conventional high-chromium iron alloy. The hammers were lasting approximately two months before requiring replacement. After switching to the FeCr15B2MnTi alloy with optimized titanium content, the service life increased to over seven months, representing a significant improvement in both performance and cost-effectiveness.

However, the transition was not without challenges. The initial trials using a low-titanium version of the alloy resulted in cracking of the overlay, which led to premature failure through spalling and delamination. The problem was traced to the high volume fraction of brittle eutectic phases that could not accommodate the thermal stresses during cooling. The solution involved increasing the titanium content to promote TiC formation and refine the primary phases, which reduced the eutectic fraction and improved the toughness of the overlay.

Another case involved the hardfacing of agricultural tillage tools, where the FeCr15B2MnTi alloy was compared with a conventional martensitic stainless steel hardfacing. The high-boron alloy provided superior wear resistance in sandy soils, but exhibited some chipping at the edges of the tools due to the high hardness and lower toughness. The solution was to apply a thinner overlay and use a more ductile buffer layer to absorb the impact energy, preventing the hard surface from chipping.

Key Questions and Reflections

The research raises several important questions that warrant further investigation. First, what is the optimal titanium content for different service conditions? The paper indicates that increasing titanium content improves toughness and reduces cracking, but excessive titanium may lead to the formation of large TiC agglomerates that act as stress concentrators and reduce wear resistance. The optimal content likely depends on the specific application and the severity of impact loading.

Second, how does the FeCr15B2MnTi alloy perform under high-temperature wear conditions? The M2B phases are thermally stable up to relatively high temperatures, but the matrix may soften and lose its supporting capacity. The addition of chromium provides some hot hardness, but the performance at temperatures above 500°C requires further investigation.

Third, what is the effect of the substrate material on the performance of the hardfacing overlay? The dilution from different substrates can significantly alter the composition of the deposited layer, affecting both the microstructure and the properties. The paper uses a specific substrate, but the results may not be directly transferable to other substrate materials.

Study Insights and Practical Recommendations

The key insight from this research is that high-boron hardfacing alloys can provide exceptional wear resistance when the microstructure is properly controlled. The titanium addition is critical for achieving the desired balance of hardness and toughness, and the transition from cracked to non-cracked welds represents a significant improvement in the practical applicability of these alloys.

From a practical standpoint, I recommend that engineers consider FeCr15B2MnTi alloys for applications requiring high wear resistance under abrasive conditions, particularly where the components are subject to impact loading. The titanium content should be optimized based on the specific application, with higher titanium for applications involving significant impact and lower titanium for applications where maximum hardness is the priority.

The process parameters must be carefully controlled to ensure sound deposition and optimal microstructure. The self-shielded open-arc process offers flexibility and portability, but the operator must be trained to maintain the correct welding parameters and to recognize the signs of inadequate shielding or excessive dilution. The use of preheat and interpass temperature control is essential for preventing cracking in thick sections or when depositing multiple layers.

Reference Value and Outlook

This research provides valuable reference data for the development and application of high-boron hardfacing alloys. The identification of the M23(C,B)6 phase as an inner constituent of the M2B phase contributes to the understanding of the solidification sequence and the microstructural evolution of these alloys. The practical finding that titanium addition can eliminate cracking is particularly important for the industrial application of these materials.

Looking ahead, the development of high-boron hardfacing alloys will likely focus on further optimizing the composition to achieve the best combination of hardness, toughness, and wear resistance. The use of multiple alloying elements, including titanium, niobium, and vanadium, may provide additional benefits in terms of grain refinement and phase modification. The application of advanced characterization techniques, such as atom probe tomography and transmission electron microscopy, will provide deeper insight into the nanoscale structure and properties of these alloys.

The practical lessons from this work should be incorporated into the material selection and process design for hardfacing applications. The importance of controlling the titanium content to prevent cracking cannot be overstated, and the process parameters must be optimized to achieve the desired microstructure and properties. The FeCr15B2MnTi alloy represents a significant advancement in hardfacing technology, and its application is expected to grow as the industry recognizes the benefits of high-boron alloys for wear-resistant applications.