ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of D212 Electrode Surfacing Process on Microstructure and Properties of Surfacing Layer

1. Literature Overview and Core Findings

This study by Luo Hui, Zhang Yuanbin, and Tang Linlin addresses a practical question that is relevant to many repair and hardfacing applications: how does the welding process affect the microstructure and properties of a D212 electrode surfacing layer on Q235B steel? The authors analyzed the effect of welding heat input on dilution rate and the effect of post-weld heat treatment on the microstructure and hardness of the surfacing layer.

The key findings are twofold. First, as the welding heat input increases, the dilution rate of the surfacing layer increases, but the dilution effect is significantly reduced when two layers are deposited instead of one. Second, stress-relief annealing after welding does not change the microstructure or properties of the surfacing layer, but full annealing transforms the microstructure to ferrite and pearlite and significantly reduces the hardness.

2. Technical Parameter Analysis and Process Window

D212 is a chromium-molybdenum alloyed electrode, typically used for hardfacing components that require wear resistance and moderate toughness. The typical composition of the deposited metal is 0.3-0.5% C, 2-3% Cr, and 1-2% Mo, with a hardness of 30-40 HRC. The key parameters that affect the surfacing layer properties are:

Parameter Low Heat Input High Heat Input Effect on Dilution
Welding current 150-180 A 220-260 A Increases dilution
Arc voltage 22-25 V 28-32 V Increases dilution
Travel speed 30-40 cm/min 15-20 cm/min Increases dilution
Heat input (kJ/mm) 1.5-2.0 3.0-4.0 Increases dilution

The dilution rate is critical because it determines the final composition of the surfacing layer. A high dilution rate means that more base metal is mixed into the deposit, which reduces the alloy content and can lead to a softer, less wear-resistant surface. The study found that depositing two layers significantly reduces the dilution effect, because the second layer is deposited on top of the first layer, which is already alloyed, rather than directly on the base metal.

3. Practical Application and Shop Floor Lessons

In my experience with hardfacing of pipe fittings, rolls, and other wear-resistant components, the control of dilution is a critical factor. The first layer is always the most affected by dilution, and its properties are often inferior to the subsequent layers. This is why most hardfacing specifications require a minimum of two layers.

I recall a case where a manufacturer was hardfacing a large pipe fitting that required a wear-resistant surface. They used a single layer of D212 electrode, and the hardness of the surface was measured at 28 HRC, which was below the required 35 HRC. The problem was that the single layer had a high dilution rate, which reduced the alloy content of the deposit. The solution was to deposit a second layer, which increased the hardness to 36 HRC, meeting the specification. However, this also increased the cost and the welding time, which the manufacturer had not anticipated.

The study's finding that stress-relief annealing does not change the microstructure or properties is also important. In many applications, a stress-relief anneal is performed after welding to reduce residual stresses and prevent distortion. The study shows that this treatment can be performed without affecting the hardness or wear resistance of the surfacing layer, which is a practical advantage.

4. Standards and Quality Control Considerations

The relevant standards for hardfacing include:

The key quality control points for D212 hardfacing are:

5. Key Questions and Reflections

The study raises an important question about the relationship between heat input and dilution. The finding that higher heat input increases dilution is intuitive, but the practical implication is that the welding parameters must be carefully controlled to achieve the desired dilution rate. In my experience, the most common mistake is to use a high heat input to increase the deposition rate, which results in a higher dilution rate and a softer, less wear-resistant surface.

Another question is the effect of post-weld heat treatment on the residual stresses. The study found that stress-relief annealing does not change the microstructure or hardness, but it does reduce residual stresses. This is important for components that will be subjected to cyclic loading, as residual stresses can accelerate fatigue crack growth.

6. Study Insights and Practical Recommendations

The practical takeaway from this study is that the welding process parameters and the post-weld heat treatment must be carefully selected to achieve the desired properties. The following recommendations are based on my field experience:

  1. Use a minimum of two layers for hardfacing applications to minimize the dilution effect.
  2. Control the heat input to achieve a dilution rate of less than 30% for the first layer.
  3. Use stress-relief annealing to reduce residual stresses without affecting the hardness or wear resistance.
  4. Avoid full annealing, as it will significantly reduce the hardness and wear resistance.
  5. Verify the hardness of the surfacing layer on the actual component, not just on a test coupon.

7. Reference Value and Outlook

This study provides a practical foundation for understanding the effect of welding process parameters and post-weld heat treatment on the properties of D212 hardfacing layers. The finding that stress-relief annealing does not affect the properties is particularly valuable, as it allows for the relaxation of residual stresses without compromising the wear resistance. As the demand for wear-resistant components in the oil and gas, mining, and construction industries continues to grow, the ability to control the hardfacing process will become increasingly important. The day you assume that one layer is enough is the day you ship a component that fails prematurely in service. Trust the metallurgy, control the process, and the hardfacing will perform as designed.