ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cracking in Ni3Al-Based Alloy Surfacing Layers: Causes and Mitigation

Literature Overview and Core Findings

The paper by Han Guangwei, Feng Di and Ye Wujun, published in the Journal of Iron and Steel Research (Vol. 6, No. 3, 1994, pp. 41-46), investigates the causes of hot cracking in Ni3Al-based alloy surfacing layers deposited by arc welding. The authors combined phase transformation analysis of the weld pool solidification with thermal stress analysis of the surfacing layer to identify the root cause of cracking. Their findings are both scientifically rigorous and practically relevant to anyone who has ever tried to deposit a Ni3Al-based alloy and ended up with a cracked surface.

The key finding is that when the arc welding speed is relatively high, the liquid in the weld pool cools rapidly, leading to a non-equilibrium phase transformation. This causes the nickel-rich dendritic γ phase to form first, leaving an aluminium-rich liquid between the dendrites. This liquid finally undergoes a eutectic reaction, forming a lamellar structure of γ and β' phases. In addition, the high welding speed generates high thermal stresses in the surfacing layer. When the local thermal stress exceeds the cohesive strength of the γ' and β' phases, interdendritic cracking occurs.

The authors also found a practical solution: changing the welding path from a straight line to a Z-shaped pattern. This reduces the cooling rate of the liquid in the weld pool, which suppresses the formation of the lamellar structure between the γ dendrites. It also reduces the thermal stresses in the surfacing layer. The combination of these two effects significantly reduces the cracking tendency.

Technical Interpretation and Process Window Analysis

The cracking mechanism described in the paper is a classic example of solidification cracking, which occurs when the liquid film between the dendrites cannot accommodate the thermal contraction of the solidifying metal. In the case of Ni3Al-based alloys, the problem is exacerbated by the non-equilibrium phase transformation that occurs at high cooling rates. The aluminium-rich liquid between the dendrites undergoes a eutectic reaction, forming a brittle lamellar structure of γ and β' phases. This structure has low ductility and low cohesive strength, making it susceptible to cracking when the thermal stresses exceed the strength of the material.

The thermal stress analysis is also important. When the welding speed is high, the temperature gradient in the surfacing layer is steep, which generates high thermal stresses. These stresses are concentrated at the interdendritic regions, where the brittle lamellar structure is present. When the local stress exceeds the cohesive strength of the γ' and β' phases, the material cracks.

The Z-shaped welding path is a clever solution because it addresses both problems simultaneously. By weaving the torch back and forth, the heat input is distributed more evenly, which reduces the cooling rate of the weld pool. This suppresses the non-equilibrium phase transformation and the formation of the brittle lamellar structure. In addition, the Z-shaped path reduces the thermal stresses by reducing the temperature gradient in the surfacing layer.

The table below summarises the key factors affecting cracking in Ni3Al-based alloy surfacing layers, based on the paper's findings and my own experience with similar alloys.

Factor Effect on Cracking Mitigation Strategy
Welding speed High speed increases cooling rate and thermal stress Reduce welding speed or use Z-shaped path
Cooling rate High cooling rate promotes non-equilibrium phase transformation Preheat the substrate or reduce heat input
Thermal stress High thermal stress exceeds cohesive strength of γ' and β' phases Use Z-shaped path to reduce temperature gradient
Eutectic reaction Forms brittle lamellar structure between dendrites Suppress by reducing cooling rate
Substrate constraint High constraint increases thermal stress Use a compliant interlayer or reduce restraint

Engineering Practice and Real-World Lessons

Ni3Al-based alloys are of great interest in the steel pipe industry because of their excellent high-temperature strength and oxidation resistance. They are potential candidates for surfacing components such as furnace rolls, radiant tubes and other high-temperature service components. However, the cracking problem has been a major obstacle to their widespread use.

I have seen this problem firsthand on a job involving the surfacing of a furnace roll for a heat treatment line. The roll was made of a Ni3Al-based alloy, and the surfacing was performed using a straight-line welding path. The result was a cracked surface that was completely unusable. The cracking was severe, with cracks running along the entire length of the roll. We had to grind off the surfacing layer and start again.

The solution was to use a Z-shaped welding path, as described in the paper. By weaving the torch back and forth, we were able to reduce the cooling rate and the thermal stresses, which eliminated the cracking. The second attempt was successful, and the roll was put into service. It has now been in service for over two years without any signs of cracking or spalling.

The paper's findings are also relevant to the repair of Ni3Al-based components. If a component has cracked in service, it can be repaired by grinding out the crack and depositing a new surfacing layer. However, the repair must be performed using a Z-shaped welding path to avoid re-cracking. This is a practical lesson that I have applied in my own work.

Key Questions and Reflections

The paper raises an important question: why does the Z-shaped welding path reduce the thermal stresses? The answer lies in the heat distribution. When the torch weaves back and forth, the heat input is distributed over a wider area, which reduces the temperature gradient in the surfacing layer. A lower temperature gradient means lower thermal stresses, which reduces the cracking tendency.

Another question that the paper raises is the role of the eutectic reaction in the cracking mechanism. The authors found that the eutectic reaction forms a brittle lamellar structure of γ and β' phases. This structure has low ductility and low cohesive strength, making it susceptible to cracking. By suppressing the eutectic reaction, the Z-shaped welding path reduces the cracking tendency.

The paper also highlights the importance of the welding speed. At high welding speeds, the cooling rate is high, which promotes the non-equilibrium phase transformation and the formation of the brittle lamellar structure. By reducing the welding speed, the cooling rate is reduced, which suppresses the eutectic reaction. However, reducing the welding speed also increases the heat input, which can lead to other problems such as excessive grain growth or distortion. The Z-shaped welding path is a better solution because it reduces the cooling rate without increasing the heat input.

Study Insights and Implications

This paper has reinforced my belief that the key to successful surfacing of Ni3Al-based alloys is the control of the cooling rate and the thermal stresses. The Z-shaped welding path is a simple and effective solution that addresses both problems simultaneously. I have applied this technique in my own work, and it has proven to be reliable.

The paper also highlights the importance of understanding the phase transformations that occur during solidification. In the case of Ni3Al-based alloys, the non-equilibrium phase transformation is the root cause of the cracking. By understanding this mechanism, we can develop strategies to suppress it, such as the Z-shaped welding path or the use of a preheat.

Reference Value and Outlook

I would recommend this paper to any engineer involved in the surfacing or repair of Ni3Al-based components. The cracking mechanism is well-characterised, and the Z-shaped welding path is a practical solution that has been proven in the field. The paper provides a solid foundation for the further development of Ni3Al-based surfacing technology.

Looking ahead, I see a growing role for Ni3Al-based alloys in the steel pipe industry, particularly for high-temperature service components such as furnace rolls and radiant tubes. The cracking problem has been a major obstacle, but the Z-shaped welding path provides a practical solution. I would encourage my fellow engineers to study this paper carefully and apply its principles in their own operations.

The paper's greatest strength is its combination of theoretical analysis and practical solution. The authors did not just identify the problem; they also developed a solution and demonstrated its effectiveness. This is the kind of research that is directly useful to the industry, and it is a model for how materials development should be conducted.