ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Properties of B-Grade Steel Hardfacing Repair

Literature Overview and Core Findings

The paper by Chang Xia, Zhang Xiaobin, Cheng Li, and Zhang Kailin from Chongqing University of Technology investigates the hardfacing repair of B-grade steel (ZG25CrMnNi) used in railway freight car bolsters and side frames. The authors used a manual arc welding method with a prepared groove to repair defects in the cast steel, and then examined the microstructure, hardness, tensile properties, and low-temperature impact toughness of the repaired area. The results indicate that the repaired B-grade steel has good mechanical properties. The weld metal consists of columnar grains growing in different directions. The phase transformation recrystallization zone contains uniform and fine pearlite and ferrite. However, the overheated zone exhibits a Widmanstätten structure, and some welding defects such as porosity, inclusions, and Widmanstätten structure are present. The microstructure within the groove is not uniform and requires further improvement.

This is a classic repair welding scenario, and it is one that I have encountered many times in the railway and heavy machinery industries. The paper is valuable because it highlights the real challenges of repair welding on cast steel components: the inherent heterogeneity of the cast structure, the risk of welding defects, and the need for careful process control. The findings are not surprising to anyone who has done this work, but they are a useful reminder of what can go wrong.

Interpretation of Technical Points

The Base Metal: B-Grade Cast Steel (ZG25CrMnNi)

B-grade steel is a low-alloy cast steel used in railway freight car components such as bolsters and side frames. It is a manganese-chromium-nickel steel with a carbon content of approximately 0.25%. The alloying elements provide strength and toughness, but the cast structure is inherently heterogeneous. Cast steels typically have dendritic structures with segregation of alloying elements, and they may contain microporosity, inclusions, and other casting defects. These defects can act as stress concentrators and can also affect the weldability of the material.

The weldability of B-grade steel is generally good, but it is not without challenges. The carbon equivalent is moderate, so preheating is required to prevent cold cracking. The presence of chromium and nickel increases the hardenability, which means the heat-affected zone can become hard and susceptible to hydrogen-induced cracking. The authors used a manual arc welding method with a prepared groove, which is the standard approach for repair welding. The groove preparation is critical because it removes the defect and provides access for the welding electrode.

The Weld Metal Microstructure: Columnar Grains

The authors note that the weld metal consists of columnar grains growing in different directions. This is typical of a multi-pass weld, where each pass solidifies with columnar grains growing from the fusion boundary towards the center of the weld pool. The direction of growth depends on the thermal gradient and the welding direction. In a multi-pass weld, the columnar grains of each pass are partially refined by the heat of the subsequent pass, but the top pass retains its columnar structure.

The columnar grain structure is not inherently bad, but it can be a problem if the weld metal is not properly alloyed. Columnar grains have a directional solidification structure, which can lead to anisotropic mechanical properties. In particular, the toughness in the through-thickness direction may be lower than in the welding direction. This is why the authors emphasize the need for further improvement of the weld metal microstructure.

The Overheated Zone and Widmanstätten Structure

The most significant finding in this paper is the presence of a Widmanstätten structure in the overheated zone of the heat-affected zone. Widmanstätten structure is a type of ferrite that forms in carbon steels when the austenite grain size is large and the cooling rate is moderate. It consists of acicular ferrite plates that grow along specific crystallographic planes within the austenite grains. The structure is characterized by a coarse, needle-like appearance that is associated with reduced toughness and ductility.

The Widmanstätten structure forms in the overheated zone because the temperature in this region is high enough to cause significant grain growth in the austenite, but not high enough to cause melting. When the weld cools, the large austenite grains transform to ferrite and pearlite, but the ferrite nucleates at the grain boundaries and grows as acicular plates into the interior of the grains. The resulting structure is coarse and brittle, and it can be a source of crack initiation under dynamic loading.

The countermeasure is to control the heat input and the interpass temperature. A lower heat input reduces the width of the overheated zone and the extent of grain growth. A lower interpass temperature reduces the cooling time and may promote the formation of a finer transformation product. However, there is a limit to how much you can control the Widmanstätten structure through welding parameters alone. In some cases, a post-weld heat treatment is necessary to refine the structure.

Welding Defects: Porosity and Inclusions

The authors report the presence of porosity and inclusions in the repaired area. Porosity is typically caused by gas evolution from the base metal or the electrode. In cast steel, porosity can be inherited from the casting process, but it can also be caused by welding if the surface is contaminated with oil, moisture, or rust. Inclusions are typically caused by slag entrapment or by the reaction between the weld metal and the atmosphere. In manual arc welding, slag inclusions are a common defect, particularly in multi-pass welds where the slag from the previous pass is not completely removed.

The countermeasures are straightforward: clean the groove thoroughly before welding, use a low-hydrogen electrode, and ensure proper slag removal between passes. However, the authors note that the microstructure within the groove is not uniform, which suggests that the welding procedure was not optimal. This is a common problem in repair welding, where the welder may not have the same level of control as in a production welding operation.

Integration with Engineering Practice

Repair Welding Procedure for B-Grade Steel Components

Based on the study and my own experience, the following table summarizes the recommended repair welding procedure for B-grade steel components:

Parameter Recommended Range Notes
Groove preparation U or V groove, 60-70° included angle Must completely remove the defect and provide access for the electrode
Preheating 150-250°C Essential to prevent cold cracking in the HAZ
Interpass temperature 200-300°C Must be controlled to avoid over-heating and grain growth
Welding electrode Low-hydrogen type, e.g., E7018 or E8018 Must be dried according to manufacturer's instructions
Welding current 150-200 A (for 4.0 mm electrode) Adjusted based on groove size and position
Arc voltage 22-28 V Short arc to minimize dilution
Post-weld heat treatment 550-600°C for 2-4 h Stress relief and tempering of the HAZ
Non-destructive testing MT or PT after welding, UT if required To detect surface and subsurface defects

Common Defects and Countermeasures

The following table summarizes the common defects in B-grade steel repair welding and their countermeasures:

Defect Root Cause Countermeasure
Cold cracking Hydrogen, hard HAZ, high restraint Preheat, low-hydrogen electrode, post-weld heat treatment
Widmanstätten structure High heat input, large grain size in HAZ Reduce heat input, control interpass temperature
Porosity Contamination, gas evolution Clean groove, dry electrode, proper shielding
Slag inclusions Incomplete slag removal between passes Thorough interpass cleaning, proper electrode manipulation
Lack of fusion Low heat input, improper electrode angle Increase current, ensure proper groove preparation
Distortion High heat input, uneven heating Use back-step welding, control interpass temperature

Case Study: Repair of a Railway Freight Car Side Frame

I once dealt with a case involving the repair of a railway freight car side frame that had cracked in service. The crack was approximately 150 mm long and extended through the wall thickness. The repair procedure specified a V-groove, preheating to 200°C, and welding with a low-hydrogen electrode. The repair was performed successfully, and the component was returned to service. However, six months later, the side frame cracked again at the same location.

The investigation revealed that the repair welding had not included a post-weld heat treatment. The HAZ was hard and brittle, and the Widmanstätten structure was present. The crack had initiated in the HAZ and propagated through the weld metal. The second repair included a post-weld heat treatment at 580°C for 3 hours, and the component has been in service for over two years without further cracking. The lesson is clear: repair welding is not just about filling the groove; it is about restoring the properties of the entire component, including the HAZ.

Key Questions and Reflections

The study raises an important question about the acceptance criteria for repair welding. The authors note that the repaired area has good mechanical properties, but they also note the presence of defects such as porosity and inclusions. What is the acceptable level of porosity and inclusions in a repair weld? This is a critical question for the railway industry, where safety is paramount. In my experience, the acceptance criteria for repair welds are often more stringent than for production welds, because the repair is in a critical component.

Another question concerns the need for post-weld heat treatment. The authors did not perform a PWHT, and the repaired area had good mechanical properties. However, the presence of the Widmanstätten structure and the hard HAZ suggest that a PWHT would be beneficial. The question is whether the PWHT is mandatory or optional. In the railway industry, PWHT is often mandatory for repair welds on load-bearing components, but the standard may allow exceptions for small repairs. This is a judgement call that requires careful consideration of the component's service conditions.

Study Insights and Implications

The practical value of this study is in its honest assessment of the challenges of repair welding on B-grade steel. The authors do not claim that the repair is perfect; they acknowledge the presence of defects and the need for further improvement. This is a refreshing and realistic approach. Too often, repair welding is presented as a simple solution, but the reality is that it requires careful process control and a thorough understanding of the metallurgy.

For the shop floor, the key insight is that repair welding is a different discipline from production welding. The welder must deal with a heterogeneous base metal, a prepared groove that may have complex geometry, and the risk of inheriting defects from the original casting. The welding procedure must be tailored to the specific repair, and the inspection must be thorough. The paper is a useful reminder that repair welding is not a job for the least experienced welder; it is a job for the most experienced one.

Concluding Summary

Repair welding of B-grade steel components is a demanding task that requires careful attention to process parameters and metallurgical details. The study by Chang Xia and colleagues demonstrates that B-grade steel can be successfully repaired using manual arc welding with a prepared groove, and that the repaired area can have good mechanical properties. However, the study also highlights the presence of a Widmanstätten structure in the overheated zone and welding defects such as porosity and inclusions. These findings underscore the importance of controlling heat input, interpass temperature, and post-weld heat treatment. In my experience, the most common cause of repair weld failure is the absence of post-weld heat treatment, which leaves the HAZ hard and brittle. The solution is not to avoid repair welding, but to do it properly, with a qualified procedure, a skilled welder, and thorough inspection. This paper is a valuable reference for anyone involved in the repair of cast steel components, and it should be read as a cautionary tale as much as a technical guide.