Machining of High-Hardness Hardfacing Layers for Remanufacturing
Literature Overview and Context
This paper by Wu Zhiyuan and colleagues from the Academy of Armored Forces Engineering investigates the machinability of high-hardness hardfacing layers during remanufacturing. The study uses orthogonal experiments to evaluate the effect of cutting parameters on tool performance when machining hardfacing deposits with hardness levels of HRC30 and HRC45. The cutting tool used is YG610, a high-performance carbide grade. The three cutting parameters evaluated are feed rate, cutting speed, and depth of cut.
This is a topic of direct practical relevance to the steel pipe and fitting industry. When a hardfaced component is worn and needs to be reconditioned, the worn surface must be machined to remove the damaged layer before applying new hardfacing. The machinability of the hardfacing deposit determines the cost and time of the reconditioning process. If the deposit is too hard or too abrasive, tool life is short, and machining costs escalate.
Experimental Design and Findings
The experimental approach uses an orthogonal experimental design, which is a systematic method for evaluating the effect of multiple factors with a limited number of trials. The three factors are feed rate, cutting speed, and depth of cut, and the response variable is tool cutting distance, which is a measure of tool life.
| Cutting Parameter | Effect on Tool Cutting Distance | Ranking |
|---|---|---|
| Feed rate | Monotonic, largest effect | 1 |
| Cutting speed | Moderate effect | 2 |
| Depth of cut | Smallest effect, especially at high hardness | 3 |
The results show that the three factors affect tool cutting distance in a consistent manner for both HRC30 and HRC45 deposits. Feed rate has the largest effect and is monotonic: as feed rate increases, tool breakage accelerates, and maximum cutting distance decreases. Cutting speed has a moderate effect. Depth of cut has the smallest effect, particularly for the high-hardness material, where increasing depth of cut has almost no effect on tool performance.
Practical Machining Strategy and Insights
The key finding from this study is the recommendation to reduce feed rate and increase depth of cut when machining hardfacing layers. This is counterintuitive to conventional machining practice, where higher feed rates are often used to improve material removal rates. However, for hardfacing deposits with their hard, abrasive carbides and brittle matrix, the situation is different.
The rationale is as follows. The hard carbides in the hardfacing deposit act as abrasive particles that cause tool wear by abrasion and micro-chipping. When the feed rate is high, the cutting edge engages a larger volume of material per revolution, increasing the mechanical load on the tool and accelerating tool breakage. By reducing the feed rate, the tool engages a smaller volume of material, reducing the mechanical load and extending tool life.
Increasing the depth of cut, on the other hand, does not significantly increase the mechanical load per unit length of cutting edge. The depth of cut primarily affects the width of the cut, not the load on the cutting edge. Therefore, increasing the depth of cut can improve material removal rate without significantly reducing tool life.
| Machining Parameter | Recommended Strategy | Rationale |
|---|---|---|
| Feed rate | Reduce | Reduces mechanical load on cutting edge, extends tool life |
| Cutting speed | Moderate | Balance between productivity and tool life |
| Depth of cut | Increase | Improves material removal rate with minimal effect on tool life |
Engineering Lessons and Recommendations
The findings from this study have direct implications for the reconditioning of hardfaced components in the steel pipe industry. When a worn hardfaced roll or guide needs to be remachined, the selection of cutting parameters is critical to the economics of the operation.
In my experience, the most common mistake is to use conventional machining parameters for hardfaced materials. Operators often use high feed rates to maximize material removal, only to find that the tool fails prematurely, resulting in frequent tool changes and high machining costs. The recommendation to reduce feed rate and increase depth of cut is counterintuitive but effective.
The use of YG610 carbide tooling is also significant. This is a high-performance carbide grade designed for machining hard and abrasive materials. For even harder deposits, such as those above HRC50, other tool materials such as ceramic or cubic boron nitride (CBN) may be required. However, these tool materials are more expensive and may not be available in all production environments.
The orthogonal experimental design used in this study is a valuable methodology for optimizing machining parameters. It allows the evaluation of multiple factors with a limited number of trials, which is particularly useful when the material being machined is expensive or difficult to obtain. The results from this study can serve as a starting point for developing machining strategies for other hardfacing alloys.
Concluding Summary
The machinability of high-hardness hardfacing layers is a critical consideration in remanufacturing operations. The orthogonal experimental study using YG610 carbide tooling reveals that feed rate has the largest and most monotonic effect on tool life, followed by cutting speed, with depth of cut having the smallest effect. The recommended machining strategy is to reduce feed rate and increase depth of cut, which maintains tool cutting capability while improving material removal rate. This counterintuitive approach is effective because it reduces the mechanical load on the cutting edge while maintaining productivity. For the steel pipe and fitting industry, this study provides valuable guidance for the reconditioning of hardfaced components, enabling cost-effective remanufacturing and extended service life of wear-resistant parts. The key lesson is to resist the temptation to use conventional machining parameters for hardfaced materials and instead adopt a strategy that prioritizes tool life over instantaneous material removal rate.
Zhuojin Pipe Fitting Co., Ltd