ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Impact-Abrasion Resistant Austenitic Hardfacing Material

Literature Overview and Core Findings

The paper by Liu Zhengjun and colleagues from Shenyang University of Technology describes the development of an austenitic hardfacing material designated EKCM50, belonging to the Fe-Mn-Cr-Mo-V alloy system, for applications involving impact abrasive wear. Comparative wear tests show that the hardfacing alloy has superior wear resistance compared to the commercial D256 welding material. Work-hardening impact tests demonstrate that the hardness of the EKCM50 hardfacing layer increases from 32 HRC to 45 HRC. After 40 minutes of impact wear testing, the weight loss of the hardfaced test material remains almost unchanged. The paper also investigates the work-hardening and wear mechanisms of this austenitic material and the effect of the alloying elements on wear resistance.

Technical Interpretation and Metallurgical Analysis

This paper addresses a specific and demanding wear condition: impact abrasion, where the surface is subjected to both high-stress abrasion and repeated impacts. The austenitic matrix is the key to this material's performance. Austenitic steels, particularly high-manganese steels like Hadfield steel, are known for their ability to work-harden under impact. The mechanism is that the austenite transforms to martensite or forms deformation twins under impact, which increases the hardness and wear resistance of the surface layer. The paper shows that the hardness increases from 32 HRC to 45 HRC after work hardening, which is a significant increase. The addition of Cr, Mo and V to the Fe-Mn system enhances the hardenability and provides additional hard phases, such as carbides, which contribute to wear resistance. The Mo and V are strong carbide formers and also improve the toughness of the matrix. The fact that the weight loss remains almost unchanged after 40 minutes of testing suggests that the material reaches a steady state where the work-hardened surface layer is resistant to further wear. This is a desirable characteristic for applications like crusher jaws, impact hammers and railway crossings, where the surface is repeatedly impacted.

Engineering Practice and Delivery Considerations

In practice, the use of austenitic hardfacing materials is well established in the mining and construction industries. The D256 material mentioned in the paper is a standard high-manganese steel hardfacing electrode, but the EKCM50 material appears to be an improvement, likely due to the addition of Cr, Mo and V. The comparison with D256 is important because it shows that the new material is not just an alternative but a better performer. The work-hardening capability is a crucial property for impact wear applications. When the surface is impacted, it hardens, which increases its resistance to further wear. However, the initial hardness is relatively low, which means that the material may wear quickly in the early stages before it work-hardens. This is a trade-off that must be considered in the design of the component. If the component is subjected to pure abrasion without impact, the austenitic material may not perform well because it will not work-harden. The paper's focus on impact wear is therefore appropriate. The alloying elements, particularly Cr, Mo and V, also affect the corrosion resistance and the high-temperature properties of the material, which may be important in some applications.

Key Questions and Reflections

One question that arises is the effect of the welding process on the work-hardening behaviour. The paper does not specify the welding process used to deposit the EKCM50 material. In practice, austenitic hardfacing materials can be deposited by various processes, including shielded metal arc welding, gas metal arc welding, flux-cored arc welding and submerged arc welding. The welding process affects the cooling rate and the resulting microstructure, which in turn affects the work-hardening behaviour. A slower cooling rate may result in a coarser microstructure, which may reduce the work-hardening capacity. Another reflection is on the effect of dilution from the base metal. If the base metal is carbon steel, the dilution will increase the carbon content and reduce the manganese content in the first layer, which could affect the austenite stability and the work-hardening behaviour. This is a critical practical consideration that must be addressed in the welding procedure qualification. The paper does not discuss the effect of dilution, but any engineer specifying this material must be aware of it.

Study Insights and Practical Implications

The key insight from this paper is that the work-hardening capability of the austenitic matrix is the primary mechanism for wear resistance under impact conditions. The addition of alloying elements such as Cr, Mo and V enhances this capability by providing additional hard phases and by improving the toughness of the matrix. The comparison with D256 shows that the EKCM50 material is a significant improvement, which suggests that the alloy design is effective. For a consumable manufacturer, this paper provides a useful reference for developing improved austenitic hardfacing materials. For a fabricator, it highlights the importance of understanding the service condition and selecting a material that is specifically designed for that condition. A material that is excellent for impact wear may not be suitable for pure abrasion, and vice versa. In my own experience, I have seen components fail because the wrong hardfacing material was selected for the service condition. The result was either excessive wear or premature cracking. This paper is a good reminder that the material selection must be based on a thorough analysis of the wear mechanism.

Conclusion and Reference Value

This paper is a valuable contribution to the field of hardfacing technology, particularly for applications involving impact abrasive wear. The development of the EKCM50 material and the demonstration of its superior wear resistance compared to D256 are significant achievements. The investigation of the work-hardening mechanism provides a clear understanding of why this material performs well under impact conditions. The finding that the weight loss becomes almost constant after 40 minutes of testing is particularly important, as it shows that the material reaches a stable, work-hardened state that is resistant to further wear. For engineers involved in the design and application of wear-resistant hardfacing for mining, construction and railway equipment, this paper offers a practical and effective solution. The higher cost of the alloying elements must be weighed against the potential for longer service life and reduced downtime, but in many cases, the economic benefits will be substantial. I would recommend this paper to anyone working on impact wear applications, and I would encourage them to consider the EKCM50 material as a viable alternative to the traditional high-manganese steels.