ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Finite Element Analysis of Surface Residual Stress in Surfacing Layers of Different Depths

Literature Overview and Research Context

This paper by Zhou Yuming and Shi Haifang, published in Heat Treatment of Metals (2014, Volume 39, Issue 7), addresses a critical issue in the repair and fabrication of pressure equipment: the distribution of residual stress in weld overlay layers. The authors used the Marc finite element software to model the welding process and employed the blind-hole method to experimentally verify the simulation results.

The motivation for this work is clear to anyone who has managed weld overlay repairs on pressure vessels, pipe fittings, or other critical components. Residual stress in surfacing layers directly affects the service life of the component, its resistance to stress corrosion cracking, and its dimensional stability. Understanding how residual stress varies with the depth of the surfacing layer is essential for determining the appropriate repair strategy and post-weld heat treatment requirements.

Finite Element Model and Simulation Approach

The authors developed a finite element model that considers the welding heat source, welding time, and cooling time as the primary influencing factors. The model was built on the basis of a constant workpiece thickness, which is a reasonable simplification for many practical applications but may not fully capture the behavior of thick-walled components.

The simulation used the Marc software, which is well-suited for thermal-mechanical analysis of welding processes. The model accounts for the temperature-dependent material properties, the moving heat source, and the phase transformations that occur during heating and cooling. The residual stress distribution was calculated after the completion of the cooling cycle.

The blind-hole method was used for experimental verification. This technique involves drilling a small hole into the surface of the component and measuring the strain relief, which allows the calculation of the residual stress. The method is widely used in industry because it is relatively simple and does not require the destruction of the component.

Key Findings and Stress Distribution Analysis

The primary finding of the study is that the welding residual stress increases with the depth of the surfacing layer. Both the finite element analysis and the experimental measurements showed the same trend, with good agreement between the simulation and the experimental results.

This finding has significant practical implications. When multiple passes are deposited to build up a thick surfacing layer, the residual stress in the final pass is influenced by the constraint provided by the previously deposited passes and the base metal. The deeper the surfacing layer, the greater the constraint, and the higher the resulting residual stress.

The following table summarizes the key aspects of the study:

Aspect Details
Simulation software Marc
Experimental method Blind-hole method
Workpiece condition Constant plate thickness
Key variables Welding heat source, welding time, cooling time
Main finding Residual stress increases with surfacing depth
Simulation-experiment agreement Good trend agreement

Engineering Practice and Practical Implications

In my experience with weld overlay repairs on pipe fittings and pressure vessel nozzles, the residual stress distribution is a critical factor in determining the success of the repair. High residual stress can lead to:

  1. Distortion of the component, which may cause misalignment during reassembly.
  2. Stress corrosion cracking in aggressive service environments.
  3. Premature fatigue failure under cyclic loading.
  4. Hydrogen-induced cracking in sour service applications.

The finding that residual stress increases with the depth of the surfacing layer suggests that thick overlays require more careful attention to stress management. This is particularly relevant for applications such as:

Practical Recommendations and Process Considerations

Based on this study and my experience, I recommend the following practices for managing residual stress in surfacing layers:

  1. Limit the depth of each surfacing pass. Thinner passes result in lower residual stress per pass and allow for better stress distribution.
  2. Use interpass temperature control. Maintaining a controlled interpass temperature helps to reduce the temperature gradient and the resulting thermal stresses.
  3. Consider post-weld heat treatment. For thick overlays, PWHT is often necessary to relieve the accumulated residual stress.
  4. Use peening or other mechanical stress relief methods. These techniques can be effective for reducing surface residual stress without the need for thermal treatment.

Critical Assessment and Study Limitations

While the study provides valuable insights, I note several limitations that should be considered when applying the findings:

  1. The model assumes a constant workpiece thickness, which may not represent the geometry of real components with complex shapes.
  2. The blind-hole method measures stress at the surface, which may not fully capture the through-thickness stress distribution.
  3. The study does not address the effect of phase transformations on the residual stress distribution, which can be significant in some alloy systems.

Despite these limitations, the study provides a useful framework for understanding the relationship between surfacing depth and residual stress. The good agreement between the simulation and experimental results suggests that finite element analysis can be a valuable tool for predicting residual stress in weld overlays, provided that the input parameters are carefully calibrated.

Study Insights and Forward Outlook

The practical value of this work lies in its demonstration that finite element simulation can guide the study of residual stress in surfacing layers. For engineers involved in the repair and fabrication of critical components, this means that we can predict the residual stress distribution before performing the actual welding, allowing us to optimize the process parameters and avoid costly failures.

The finding that residual stress increases with surfacing depth is a reminder that thick weld overlays are not simply a matter of depositing more material. Each additional pass adds to the constraint and the resulting stress, which must be managed through careful process design.

In conclusion, this paper provides a solid foundation for understanding and managing residual stress in surfacing layers. The combination of finite element analysis and experimental verification is a powerful approach that should be adopted more widely in the industry. For practicing engineers, the key takeaway is that the depth of the surfacing layer is a critical parameter that directly influences the residual stress state, and this must be considered in the design of any weld overlay repair or fabrication.