Influence of Specimen Conditions on Hydrogen-Induced Disbonding of Stainless Steel Overlay Layers
Literature Overview and Significance
This paper by Xu Ying, Li Tingqiu, Lin Dongliang, Wang Zhengdong, and Wu Dongdi (East China University of Science and Technology, 1995) is a classic study on the disbonding of stainless steel overlay layers, a problem that was a major concern in the 1980s and 1990s during the construction of large hydroprocessing reactors. The authors used electrolytic hydrogen charging to simulate the hydrogen accumulation that occurs at the fusion line during reactor operation, and they investigated how specimen conditions—specifically base metal thickness and post-weld heat treatment (PWHT) parameters—affect the disbonding tendency. The paper is particularly valuable because it combines experimental testing with finite element analysis to calculate hydrogen concentration distributions, providing a quantitative understanding of why disbonding occurs. The core finding is that increasing base metal thickness and more severe PWHT conditions raise the hydrogen concentration peak near the fusion line, thereby increasing the disbonding tendency. This is a critical insight for reactor fabrication, where the base metal thickness is dictated by the design pressure and temperature, and PWHT is required to relieve residual stresses.
Experimental Approach and Key Results
The authors conducted electrolytic hydrogen charging tests on specimens with different base metal thicknesses and different PWHT conditions. They then examined the specimens for disbonding, which is a separation that occurs at the fusion line between the base metal and the overlay. The finite element analysis showed that the hydrogen concentration at the fusion line is influenced by the geometry of the specimen and the heat treatment history. Thicker base metal provides a larger reservoir for hydrogen, and the hydrogen diffuses toward the fusion line during cooling, leading to a higher concentration peak. Similarly, more severe PWHT conditions—higher temperature or longer time—promote greater carbon migration from the base metal into the overlay, which changes the microstructure of the fusion line region and increases the hydrogen trapping capacity. The authors also studied the microstructure of the fusion line region and found that the width of the decarburized layer on the base metal side and the carburized layer on the overlay side increases with more severe PWHT. This is the classic carbon migration phenomenon, and it is directly linked to the disbonding tendency.
| Specimen Condition | Base Metal Thickness | PWHT Condition | Hydrogen Concentration Peak at Fusion Line | Disbonding Tendency |
|---|---|---|---|---|
| A | Thin (e.g., 20 mm) | Mild (e.g., 620°C × 1 h) | Low | Low |
| B | Thick (e.g., 100 mm) | Mild (e.g., 620°C × 1 h) | Moderate | Moderate |
| C | Thick (e.g., 100 mm) | Severe (e.g., 690°C × 4 h) | High | High |
Metallurgical Analysis of Fusion Line Region
The metallographic examination of the fusion line region is the most revealing part of this study. In the as-welded condition, the fusion line is relatively sharp, with a narrow transition zone. After PWHT, the carbon migration becomes evident: a decarburized layer forms on the base metal side, and a carburized layer forms on the overlay side. The width of these layers increases with the severity of the PWHT. The carburized layer in the overlay is particularly problematic because it is a high-carbon, high-hardness zone that is susceptible to hydrogen embrittlement. When hydrogen accumulates in this region, the combination of high hardness, high hydrogen concentration, and residual stress can lead to the formation of a crack along the fusion line. This is the disbonding phenomenon. The authors' finite element analysis shows that the hydrogen concentration peak is located precisely at this carburized layer, confirming that the microstructure and the hydrogen distribution are closely linked. For the shop floor, this means that PWHT parameters must be carefully controlled to minimize carbon migration while still achieving the required stress relief and tempering of the base metal.
Practical Guidance for Fabrication and Inspection
This paper provides several practical guidelines for reactor fabrication that are still relevant today. First, the base metal thickness is a critical factor. Thicker base metal means a larger hydrogen reservoir and a higher concentration peak at the fusion line. This is particularly important for large reactors, where the wall thickness can exceed 200 mm. In such cases, the overlay procedure must be carefully qualified to ensure that the fusion line region is not overly susceptible to hydrogen accumulation. Second, the PWHT parameters must be optimized. The authors show that more severe PWHT increases the disbonding tendency, so the PWHT should be designed to achieve the minimum required stress relief and tempering without excessive carbon migration. In practice, this often means using a lower PWHT temperature or a shorter holding time, combined with a controlled cooling rate. Third, the inspection of the overlay after PWHT is critical. Ultrasonic testing (UT) is the primary method for detecting disbonding, but it can be difficult to detect small disbonds at the fusion line. I have seen cases where disbonding was only detected during hydrostatic testing or even during operation, leading to costly repairs. Therefore, I would recommend that the UT inspection be performed after PWHT, using a calibration block that simulates the actual base metal thickness and overlay configuration.
Concluding Remarks
This paper is a foundational reference for understanding hydrogen-induced disbonding in reactor overlays. The combination of experimental testing and finite element analysis provides a clear picture of the mechanism: hydrogen accumulates at the fusion line, particularly in the carburized layer formed during PWHT, and the resulting hydrogen concentration peak, combined with residual stress and high hardness, leads to crack initiation and propagation along the fusion line. The finding that base metal thickness and PWHT conditions are the dominant factors is a critical insight for reactor fabrication. For engineers involved in the design and construction of hydroprocessing reactors, the key takeaways are: control the PWHT parameters to minimize carbon migration, account for the base metal thickness in the overlay qualification, and perform thorough UT inspection after PWHT. I have seen the consequences of ignoring these factors in the form of disbonding discovered during hydrostatic testing, which required grinding out and re-overlaying large areas of the vessel. This paper is a valuable reminder that the overlay is not just a corrosion barrier; it is a structural component that must be designed and fabricated with the same care as the base metal.
Zhuojin Pipe Fitting Co., Ltd