ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Electrochemical Corrosion Failure of NiCrBSi Surfacing Layer

Literature Overview and Core Findings

This paper by Zhao Weimin and colleagues from the University of Petroleum and Xi'an Jiaotong University addresses a problem I have seen too many times on the shop floor: the premature failure of nickel-based alloy surfacing layers applied to carbon steel substrates. The study focuses on NiCrBSi alloy deposited on carbon steel and evaluated in 3.5% NaCl solution, which is essentially a simulated seawater environment. The authors used both immersion corrosion testing and electrochemical impedance spectroscopy (EIS) with potentiostatic polarization to accelerate the corrosion process.

The core finding is that inclusions within the surfacing layer are the fundamental cause of localized corrosion. The paper demonstrates that reducing the number and volume of inclusions directly improves the corrosion resistance of the deposited layer. This is a critical insight that many production engineers overlook. We tend to focus on the macroscopic properties like hardness and chemical composition, but the microstructural cleanliness of the deposit is what determines long-term performance in corrosive service.

The study also establishes that the corrosion system follows a typical Randles equivalent circuit, meaning the corrosion process is charge-transfer controlled. The impedance decreases slightly as corrosion progresses, indicating a stable but slowly degrading protective layer. However, when localized corrosion becomes severe enough to expose the substrate, the equivalent circuit changes significantly, and the impedance drops dramatically. Even without macroscopic galvanic corrosion between the cladding and the substrate, the failure occurs.

Technical Interpretation and Practical Implications

The Role of Inclusions in Localized Corrosion

From my experience in manufacturing corrosion-resistant lined pipe and clad components, the inclusion issue is real and persistent. Inclusions in NiCrBSi deposits typically originate from several sources:

Inclusion Source Typical Origin Effect on Corrosion
Slag inclusions Inadequate slag removal between passes Creates crevices and pitting initiation sites
Oxide inclusions Poor shielding gas coverage or excessive oxidation Disrupts passive film formation
Tungsten inclusions Tungsten electrode contamination during GTAW Creates galvanic cells within the deposit
Porosity Gas entrapment or hydrogen evolution Provides pathways for electrolyte penetration
Intermetallic precipitates Improper post-weld heat treatment Causes selective phase corrosion

The paper's conclusion that reducing inclusion count and size improves corrosion resistance aligns with what I have observed in practice. In one project involving clad pipe for offshore service, we had to reject an entire batch of surfacing because the inclusion content exceeded the specification. The customer's corrosion testing showed pitting at inclusion sites within weeks, while the acceptable batches lasted for years.

The Randles Equivalent Circuit and Corrosion Monitoring

The establishment of the Randles equivalent circuit for the NiCrBSi corrosion system is practically useful. It means that the corrosion process is dominated by charge transfer resistance and double-layer capacitance. For condition monitoring, this suggests that measuring the polarization resistance over time can provide a reliable indication of the cladding's health.

The paper's finding that natural corrosion potential can be used to detect cladding failure is particularly valuable for in-service monitoring. In my experience with lined vessels and pipes, we have used potential monitoring to detect when a lining has breached. The potential shifts significantly when the substrate becomes exposed because the galvanic couple between the nickel-based alloy and the carbon steel creates a distinct potential signature.

Failure Mechanism When Substrate is Exposed

The paper makes an important point about what happens when the substrate becomes exposed. Even without macroscopic galvanic corrosion, the system fails. This is because the exposed carbon steel creates a localized anode, and the surrounding nickel-based alloy acts as a large cathode. The resulting galvanic cell accelerates the corrosion of the carbon steel, leading to rapid penetration.

In my experience, this is exactly what happens in practice. I have seen cases where a small defect in a nickel-based cladding led to complete perforation of the carbon steel substrate within months, even though the cladding itself was still in good condition. The lesson is clear: any defect that exposes the substrate must be repaired immediately, regardless of how small it appears.

Engineering Practice and Lessons Learned

Production Control Measures

Based on this research and my own experience, I recommend the following practical measures to improve the corrosion resistance of NiCrBSi surfacing layers:

  1. Strict control of welding consumables: Use only low-inclusion, high-purity filler metals. Verify the inclusion content of incoming wire or rod stock.
  2. Optimized shielding gas: Use argon with high purity (99.99% minimum) and adequate flow rates. Check for leaks in the gas delivery system.
  3. Proper interpass cleaning: Remove all slag and oxide between passes using stainless steel wire brushes or grinding. Never use carbon steel brushes, which can contaminate the deposit.
  4. Controlled heat input: Maintain the heat input within the specified window to prevent excessive dilution while ensuring adequate fusion. Excessive heat input increases dilution and promotes inclusion formation.
  5. Post-weld inspection: Perform 100% visual inspection and appropriate non-destructive testing. Use ultrasonic testing to detect subsurface inclusions and lack of fusion.

The Dilution Dilemma

One of the challenges I have faced with NiCrBSi surfacing is the dilution dilemma. The surfacing layer must have sufficient dilution to ensure metallurgical bonding with the substrate, but excessive dilution degrades the corrosion resistance by introducing iron into the deposit. The paper's findings reinforce that the optimal dilution window is narrow.

In practice, I have found that a dilution rate of 10% to 15% is typically acceptable for NiCrBSi surfacing on carbon steel. At dilution rates above 20%, the iron content in the deposit increases significantly, and the corrosion resistance drops noticeably. At dilution rates below 8%, the risk of lack of fusion increases.

A Case from the Field

I recall a specific project involving a large pressure vessel for a petrochemical plant. The vessel required a NiCrBSi surfacing layer on the internal surface to resist a highly corrosive process stream. The initial production run showed good appearance and hardness, but the customer's corrosion testing revealed localized pitting after only 500 hours of exposure.

Investigation revealed that the surfacing operation had been performed with an insufficient shielding gas flow rate. The resulting oxide inclusions were concentrated in the upper portions of the deposit, exactly where the corrosion testing showed pitting. After correcting the shielding gas parameters and implementing stricter interpass cleaning procedures, the reworked vessel passed all corrosion testing requirements.

Key Questions and Reflections

Is the 3.5% NaCl Solution Representative?

The paper uses 3.5% NaCl solution to simulate seawater. While this is a standard test solution, I question whether it adequately represents all service environments. In many applications, the corrosive medium is more complex, containing chlorides, sulfides, and other aggressive species. The corrosion mechanism may differ significantly in these environments.

For example, in sour service environments containing hydrogen sulfide, the failure mechanism shifts from pitting corrosion to sulfide stress cracking. The presence of inclusions still plays a role, but the mechanism is different. This is an area where further research is needed.

How Does the Inclusion Size Distribution Affect Corrosion?

The paper states that reducing inclusion count and size improves corrosion resistance. However, it does not provide quantitative data on the relationship between inclusion size distribution and corrosion rate. In my experience, the critical inclusion size for pitting initiation is typically around 1 to 5 micrometers. Inclusions larger than this threshold are much more likely to initiate pitting.

This has practical implications for quality control. Simple inclusion counting may not be sufficient; we need to understand the size distribution and the maximum inclusion size. This requires careful metallographic examination at appropriate magnifications.

The Importance of Electrode Potential Monitoring

The paper's conclusion that natural corrosion potential can be used to monitor cladding failure is practical and useful. However, the implementation of potential monitoring in real structures requires careful consideration. The reference electrode must be stable and properly positioned. The potential readings must be corrected for ohmic drop and temperature effects.

In my experience, potential monitoring is most effective when combined with other techniques, such as electrochemical impedance spectroscopy or linear polarization resistance. A multi-technique approach provides more reliable data and reduces the risk of false alarms.

Study Insights and Implications

This paper provides a solid scientific foundation for understanding the corrosion failure of NiCrBSi surfacing layers. The key insight is that inclusions are the root cause of localized corrosion, and their control is essential for achieving reliable performance. This aligns with my practical experience and reinforces the importance of process control in surfacing operations.

The paper also highlights the value of electrochemical impedance spectroscopy as a diagnostic tool. In my experience, EIS is underutilized in production quality control. Many manufacturers rely solely on visual inspection and hardness testing, which do not detect the subtle microstructural features that control corrosion resistance. EIS can provide a rapid, non-destructive assessment of the corrosion resistance of a surfacing layer.

For the industry, the practical implications are clear:

Area Recommended Action
Consumable control Verify inclusion content of incoming filler metals
Process control Optimize shielding gas, heat input, and interpass cleaning
Quality control Implement EIS or polarization resistance testing
In-service monitoring Use electrode potential monitoring for critical components
Defect management Repair any defect exposing the substrate immediately

Concluding Thoughts

The study by Zhao Weimin and colleagues is a valuable contribution to the understanding of NiCrBSi surfacing layer corrosion. It confirms what many of us have suspected from practical experience: inclusions are the primary culprit in localized corrosion failure. The paper provides a scientific basis for the process control measures we implement on the shop floor.

For the practicing engineer, the key takeaways are clear. Control the inclusions, and you control the corrosion. This requires attention to every aspect of the surfacing operation, from consumable quality to shielding gas purity to interpass cleaning. It also requires appropriate quality control measures that can detect inclusion problems before they become service failures.

I would recommend this paper to any engineer involved in surfacing operations for corrosive service. The findings are directly applicable to the design, production, and inspection of NiCrBSi surfacing layers. The use of electrochemical techniques for quality control and condition monitoring is a practice that should be more widely adopted in our industry.