ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Welding Defect Analysis and Improvement Measures for Austenitic Stainless Steel Surfacing Layers

Literature Overview and Core Technical Points

This paper by Wang Longhu et al. (2023) from Shared Foundry Co., Ltd. addresses a problem that I have encountered many times in my career: cracking and slag inclusions in austenitic stainless steel corrosion-resistant surfacing layers. The context here is a nuclear power high-pressure and intermediate-pressure outer casing, which is a critical component where weld quality is paramount.

The paper identifies two distinct defect types: microcracks caused by NbC phase formation that shifts grain boundaries at high temperature, and slag inclusions that are inherent to the characteristics of austenitic filler materials. The solution is a combination of no preheat, small current, low heat input, interlayer temperature control at or below 150°C, and narrow weaving. This approach was validated on the actual component and has been adopted for similar products.

Metallurgical Analysis and Process Window

The NbC Grain Boundary Shifting Mechanism

The microcrack mechanism described in this paper is a classic example of a metallurgical problem that is often misunderstood. When welding austenitic stainless steel with niobium-stabilized filler (such as ER347 or ERNiCr-3), the niobium combines with carbon to form NbC. At high temperatures, the NbC phase precipitates at grain boundaries and causes them to shift or migrate.

This grain boundary shifting creates a condition where the boundary is no longer in its original position, and the newly exposed regions have different composition and properties. When the weld cools and contracts, the thermal stresses concentrate at these shifted boundaries, leading to microcracks. This is a form of hot cracking that occurs in the solidification temperature range.

Defect Type Root Cause Mechanism
Microcracks NbC phase formation at high temperature Grain boundary shifting, stress concentration
Slag inclusions Austenitic filler material characteristics Viscous slag, poor slag removal

The Slag Inclusion Problem

Slag inclusions in austenitic stainless steel surfacing are a different problem. Austenitic filler materials tend to produce a viscous slag that is difficult to remove completely between passes. The slag can become trapped in the weld if the interpass cleaning is not thorough, or if the welding technique does not allow the slag to float to the surface.

The paper notes that this is inherent to the material characteristics of austenitic welding consumables. The slag system used in these electrodes is designed to provide adequate protection, but it has a tendency to remain in the weld pool longer than desired.

The Low Heat Input Approach

The solution proposed by the authors is a combination of:

Parameter Recommended Value Rationale
Preheat None Preheating increases heat input and NbC formation
Welding current Reduced from standard Lowers heat input, reduces grain growth
Heat input Low Minimizes thermal stress and NbC precipitation
Interlayer temperature ≤150°C Prevents excessive heat buildup
Weaving technique Narrow Reduces heat concentration, improves slag control

The no-preheat requirement is counterintuitive to many welders who are accustomed to preheating to prevent cracking. However, in this case, preheating actually contributes to the problem by increasing the peak temperature and the time at temperature, which promotes NbC precipitation and grain boundary shifting.

The Role of Interlayer Temperature Control

Controlling the interlayer temperature at or below 150°C is critical. In multi-pass welding, the heat from each pass builds up in the component. If the interlayer temperature is not controlled, the component can reach temperatures well above 150°C, which increases the time at temperature for the previously deposited layers and promotes NbC formation.

The practical implementation of this control requires either natural cooling between passes or forced cooling with air or water. In many cases, the component must be allowed to cool for several minutes between passes, which reduces productivity but is necessary for quality.

Engineering Practice and Lessons Learned

Application to Nuclear Power Components

The context of this paper is a nuclear power high-pressure and intermediate-pressure outer casing. This is a component where weld quality is critical because it operates under high pressure and in a corrosive environment. The surfacing layer provides corrosion resistance, and any defect in this layer can lead to premature failure.

The authors describe the quality control sequence: non-destructive testing (NDT) after welding, followed by penetrant testing (PT) after completion. The defects were found by PT, which is the appropriate method for detecting surface-breaking defects in austenitic stainless steel.

Inspection Method Defect Detected Timing
NDT (ultrasonic or radiographic) Internal defects After welding
Penetrant testing (PT) Surface-breaking defects After completion

The PDCA Approach to Defect Resolution

The development of the improved welding procedure follows a classic PDCA (Plan-Do-Check-Act) cycle:

  1. Plan: Identify the defect types and root causes through metallographic examination.
  2. Do: Implement the improved welding parameters (no preheat, low heat input, interlayer temperature control).
  3. Check: Verify the effectiveness through NDT and PT after welding.
  4. Act: Standardize the procedure for future components.

This is exactly the right approach. You cannot simply change welding parameters and hope for the best. You need to understand the root cause of the defect, then develop a targeted countermeasure, then verify it works, then standardize it.

Common Defects and Countermeasures for Austenitic Surfacing

Defect Root Cause Countermeasure
Microcracks (hot cracking) NbC precipitation, grain boundary shifting No preheat, low heat input, interlayer temp ≤150°C
Slag inclusions Viscous slag from austenitic filler Narrow weaving, thorough interpass cleaning
Porosity Moisture, gas entrapment Proper electrode drying, adequate shielding gas
Lack of fusion Low heat input, poor technique Maintain proper arc length, use appropriate current
Distortion High heat input, residual stress Low heat input, controlled interlayer temperature

The 5W2H Analysis

A structured 5W2H analysis of the problem:

Study Insights and Implications

This paper is a valuable case study in defect analysis and process improvement. The key insight is that the welding procedure must be designed based on the metallurgical characteristics of the materials involved, not just on general welding practice.

The NbC grain boundary shifting mechanism is a subtle metallurgical phenomenon that is often overlooked. Many welders would attribute microcracks to residual stress or improper technique, but the root cause here is a specific phase transformation that occurs at high temperature. Understanding this mechanism allows for a targeted solution: reduce the time at temperature to minimize NbC precipitation.

The slag inclusion problem is also instructive. Austenitic stainless steel welding consumables have a different slag system than carbon steel consumables. The slag is more viscous and requires more careful interpass cleaning. The narrow weaving technique helps because it reduces the amount of slag that can be trapped.

For the pipe and fitting industry, this paper has direct relevance to the surfacing of corrosion-resistant alloys on carbon steel pipe. In many applications, such as CRA clad pipe for oil and gas service, the surfacing layer is austenitic stainless steel or nickel-based alloy. The same defect mechanisms can occur, and the same countermeasures apply.

Conclusion

The paper by Wang Longhu et al. provides a clear and practical solution to a common problem in austenitic stainless steel surfacing. The microcracks were caused by NbC phase formation that shifts grain boundaries at high temperature, and the slag inclusions were inherent to the austenitic filler material characteristics. The solution — no preheat, small current, low heat input, interlayer temperature control ≤150°C, and narrow weaving — was validated on a nuclear power component and has been adopted for similar products. The key lesson is that welding procedures must be developed based on a thorough understanding of the metallurgical mechanisms involved, not just on general practice. The PDCA approach used here is a model for defect resolution in any welding operation. For the shop floor, this means that when you encounter defects in austenitic surfacing, you need to look beyond the obvious and understand the root cause before changing parameters. This paper should be required reading for any welding engineer involved in corrosion-resistant surfacing of pressure components.