ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

The Fusion Zone in Stainless Steel Cladding: Composition, Microstructure, and What the Shop Floor Must Know

Literature Overview and Why This Paper Still Matters

This 1999 study by Liu Yixiang and Wu Jingzi, published in Physical Testing and Chemical Analysis (Physical Volume), examines the fusion zone of stainless steel cladding using electron probe microanalysis (EPMA) and transmission electron microscopy (TEM). The paper reports three key findings: a martensitic band exists in the fusion zone in both as-welded and post-weld heat treated (PWHT) states; chromium and nickel exhibit linear distribution with a compositional gradient across the fusion zone; and PWHT causes carbon to segregate in the fusion zone, leading to extensive carbide precipitation.

I have spent thirty years in the pipe and fitting business, and I can tell you this paper addresses one of the most misunderstood areas in cladding work. The fusion zone is not just a transition region; it is the weakest link in many clad components, and the reasons are metallurgical, not just mechanical. When we clad the internal surface of a pipe or a fitting with stainless steel, we are creating a dissimilar metal joint between carbon steel and stainless steel. The fusion zone is where the dilution of the stainless steel filler by the carbon steel base occurs, and that dilution is what creates the martensitic band.

Technical Interpretation: The Martensitic Band and the Compositional Gradient

The martensitic band forms because the chemical composition in the fusion zone falls within the martensite-forming range of the Schaeffler or WRC-1992 diagram. When the carbon steel base dilutes the stainless steel filler, the nickel and chromium equivalents shift, and the resulting microstructure can be fully martensitic, even though the filler itself is austenitic. The paper shows that chromium and nickel concentrations change linearly across the fusion zone, which means the dilution ratio is not abrupt but gradual. This is critical because it tells us that the width of the martensitic band is controlled by the welding parameters, particularly the heat input and the deposition technique.

Parameter As-Welded State After PWHT
Martensitic Band Present, narrow Present, but with carbide precipitation
Cr/Ni Distribution Linear gradient Linear gradient, but carbon segregation occurs
Carbide Precipitation Minimal Extensive, particularly at grain boundaries
Microstructure Martensite + retained austenite Martensite + carbides + tempered structures

The carbon segregation after PWHT is a particularly important finding. In the as-welded state, carbon is distributed relatively uniformly. But after PWHT, carbon migrates to the fusion zone because the martensitic band has a different solubility for carbon than the adjacent austenitic and ferritic regions. This carbon enrichment leads to carbide precipitation, which can significantly reduce the corrosion resistance of the fusion zone. For a clad pipe or fitting that is going to be used in a corrosive service environment, this is a serious concern.

Practical Implications for Manufacturing and Delivery

On the shop floor, we see the consequences of this fusion zone behavior in several ways. First, when we perform a bend test on a clad pipe, the failure often occurs not in the weld metal or the base metal, but right at the fusion zone. This is because the martensitic band is hard, brittle, and has low toughness. Second, when we perform hardness surveys across a clad joint, we see a hardness spike at the fusion zone, which can be 20 to 30 HRC higher than the adjacent regions. This hardness spike is a direct indicator of the martensitic band.

For the delivery side, this matters because many specifications require that the hardness of a clad component not exceed a certain value. If the fusion zone hardness is too high, the component may be rejected. I have seen this happen on a project where we supplied clad pipe for a sour service application. The hardness at the fusion zone was exceeding the 22 HRC limit specified in the project requirements, and we had to adjust our welding parameters to reduce dilution and narrow the martensitic band.

What the Shop Floor Must Do Differently

Based on this paper and my own experience, I would recommend the following practical measures when cladding carbon steel pipe or fittings with stainless steel:

  1. Control the dilution ratio by using a buttering layer. Deposit a nickel-based or high-nickel buttering layer on the carbon steel surface before applying the stainless steel cladding. This reduces the carbon pickup and shifts the fusion zone composition away from the martensite-forming range.
  2. Use low heat input techniques. Lower heat input reduces the width of the fusion zone and the degree of dilution, which narrows the martensitic band.
  3. Consider the PWHT cycle carefully. If PWHT is required, the temperature and time must be controlled to minimize carbon segregation and carbide precipitation. A lower PWHT temperature with a longer holding time may be preferable to a higher temperature with a short time.
  4. Perform a hardness survey across the fusion zone after cladding and after PWHT. This is the most reliable way to detect the presence and extent of the martensitic band.

Key Questions and Reflections

The paper raises an important question: is the martensitic band always detrimental? In some applications, a thin martensitic band may be acceptable, particularly if the component is not subjected to severe corrosion or hydrogen charging. However, in sour service or where hydrogen-induced cracking (HIC) is a concern, the martensitic band is a potential crack initiation site. The carbide precipitation after PWHT further exacerbates this risk.

I have also seen cases where the martensitic band was beneficial. In some wear-resistant cladding applications, a hard martensitic layer is actually desired. But for corrosion-resistant cladding, it is a problem. This is why the application and service conditions must be carefully considered before deciding on the cladding approach.

Study Insights and Implications for the Industry

This paper is a reminder that the fusion zone is not a simple transition region. It is a complex microstructural zone that can significantly affect the performance of a clad component. The findings about carbon segregation after PWHT are particularly important because many fabricators assume that PWHT will homogenize the microstructure and relieve residual stress. In reality, it can cause carbon to segregate and form carbides, which may reduce corrosion resistance.

For the pipe and fitting industry, this means we must pay close attention to the cladding procedure qualification. The procedure qualification test should include not only tensile and bend tests, but also hardness surveys, metallographic examination, and corrosion tests on the fusion zone. The qualification should be performed on the actual production geometry, not just on a flat plate, because the dilution ratio can vary with the component geometry.

Reference Value and Outlook

This paper, although published in 1999, remains highly relevant today. The fundamental metallurgical principles have not changed, and the challenges of cladding carbon steel with stainless steel are still present in our industry. The use of advanced cladding techniques, such as laser cladding and explosive cladding, may reduce the fusion zone width, but the martensitic band will still exist if there is any dilution.

In my view, the most important takeaway from this paper is the need to understand the fusion zone as a distinct microstructural entity, not just a boundary. We need to design our cladding procedures with this in mind, and we need to ensure that our quality control measures are capable of detecting and evaluating the fusion zone characteristics. The next time you are qualifying a cladding procedure, ask yourself: what is happening in the fusion zone, and will it perform in the service environment? If you cannot answer that question, you are not ready to ship the product.