Cracking Failure in Remanufactured Large Hot-Rolling Backup Rolls: A Veteran's Analysis of the Cladding Layer
Literature Overview and Core Problem Statement
This 2022 paper by Nie Binying, published in Materials Science and Technology, investigates early-stage cracking in the cladding layer of remanufactured large hot-rolling backup rolls. The study identifies the failure mechanism as low-cycle contact fatigue, caused by excessive retained austenite and insufficient martensite in the cladding layer, which results in low hardness and low strength. The paper proposes a high-temperature tempering heat treatment to transform retained austenite into martensite, thereby improving the hardness and strength of the cladding layer and preventing early cracking.
This is a practical problem that I have encountered in the field. Backup rolls for hot rolling mills are massive components, often weighing tens of tonnes. When they are remanufactured, the worn surface is typically removed by machining, and a new wear-resistant layer is deposited by cladding. The cladding layer must have high hardness and sufficient toughness to withstand the cyclic contact stresses and thermal cycling of the rolling process. If the cladding layer has too much retained austenite, it will be too soft and will deform plastically under load, leading to surface fatigue cracking.
Technical Interpretation: The Role of Retained Austenite and Contact Fatigue
The paper's key finding is that the cladding layer contained excessive retained austenite, which reduced its hardness and strength. In a typical cladding material for backup rolls, the microstructure should be primarily martensite with some retained austenite. However, if the alloy composition is not properly balanced, or if the cooling rate after cladding is too slow, a significant amount of austenite can be retained at room temperature.
| Microstructural Feature | Desired Condition | Failure Condition |
|---|---|---|
| Retained Austenite | Less than 10% | Greater than 20% |
| Martensite | Primary phase | Insufficient content |
| Hardness | 55-60 HRC | Below 50 HRC |
| Contact Fatigue Resistance | High | Low, leading to early cracking |
The low-cycle contact fatigue mechanism is well understood. When a roll rotates under load, the surface experiences cyclic Hertzian contact stresses. If the surface material is too soft, the subsurface material will yield, and after many cycles, cracks will initiate at the subsurface and propagate to the surface, causing spalling and cracking. The paper correctly identifies that the excessive retained austenite reduces the yield strength of the cladding layer, making it more susceptible to this failure mode.
Practical Implications for Remanufacturing and Quality Control
In my experience, the remanufacturing of backup rolls is a high-stakes operation. The cost of a new backup roll is substantial, and the downtime associated with a roll failure can be enormous. When we remanufacture a roll, we must ensure that the cladding layer will perform at least as well as the original forged or cast roll.
The paper's recommendation to use high-temperature tempering to transform retained austenite into martensite is sound, but it must be carefully controlled. The tempering temperature must be high enough to allow the retained austenite to transform, but not so high that the martensite is over-tempered and loses hardness. The tempering time must also be optimized to ensure complete transformation without excessive grain growth.
| Heat Treatment Parameter | Recommended Range | Effect |
|---|---|---|
| Tempering Temperature | 500-600°C | Transforms retained austenite to martensite |
| Tempering Time | 2-4 hours | Ensures complete transformation |
| Cooling Rate | Slow, air cooling | Prevents re-formation of retained austenite |
| Post-Temper Hardness | 55-60 HRC | Confirms adequate martensite content |
What the Shop Floor Must Do Differently
Based on this paper and my own experience with roll remanufacturing, I would recommend the following:
- Conduct a thorough microstructural analysis of the cladding layer before and after heat treatment. This should include retained austenite measurement using X-ray diffraction (XRD) or magnetic induction methods. A retained austenite content above 15% is a red flag.
- Perform a hardness survey across the cladding layer and into the substrate. The hardness should be uniform and within the specified range. A hardness drop at the interface may indicate inadequate bonding or a soft zone.
- Verify the heat treatment cycle with a thermocouple attached to the roll surface. The temperature must be uniform across the entire roll face, and the heating and cooling rates must be controlled to prevent thermal distortion.
- Consider the service conditions. If the roll will be used in a high-temperature rolling application, the cladding material must have sufficient temper resistance to maintain its hardness at elevated temperatures.
Key Questions and Reflections
This paper raises an important question: why does the retained austenite content vary so much between different cladding operations? In my experience, the variation is often due to differences in the cladding process parameters, such as the preheat temperature, the interpass temperature, and the cooling rate. If the interpass temperature is too high, the cladding layer will cool slowly, allowing more austenite to be retained. Conversely, if the interpass temperature is too low, the cladding layer may crack due to high residual stress.
Another question is whether the high-temperature tempering treatment is always beneficial. In some cases, the retained austenite may be beneficial for toughness, particularly in applications where impact resistance is important. However, for backup rolls, the primary requirement is hardness and wear resistance, so the retained austenite should be minimized.
Study Insights and Implications for the Industry
This paper is a valuable contribution to the field of roll remanufacturing. It provides a clear explanation of the failure mechanism and a practical solution. The key insight is that the cladding layer's microstructure must be carefully controlled, not just in terms of hardness, but also in terms of the phase composition. Retained austenite is often overlooked as a factor in roll performance, but this paper shows that it can be the root cause of premature failure.
For the pipe and fitting industry, this paper has indirect relevance. We also use cladding to repair or enhance components, and the same principles apply. When we clad a pipe or fitting for wear resistance, we must ensure that the cladding layer has the right balance of hardness and toughness. Excessive retained austenite can lead to premature failure, just as it does in backup rolls.
Reference Value and Outlook
This paper is a good example of how failure analysis can lead to process improvement. By identifying the root cause of the cracking, the author was able to propose a heat treatment that resolves the problem. This is the kind of systematic approach that we should all apply in our own work.
In the future, I expect to see more attention paid to the control of retained austenite in cladding layers. Advanced techniques, such as cryogenic treatment, may be used to further reduce retained austenite content. However, the high-temperature tempering approach described in this paper is simple, cost-effective, and suitable for large components like backup rolls.
The next time you are involved in a remanufacturing project, remember this paper. Ask yourself: what is the retained austenite content of my cladding layer, and is it within the acceptable range? If you cannot answer that question, you are taking a risk that could cost you a roll, a production line, and a lot of money.
Zhuojin Pipe Fitting Co., Ltd