ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hardfacing Process Parameters for H13 Steel Die Cavity Surfaces

Literature Overview and Practical Significance

This paper by Li Kunshu from Laiwu Vocational and Technical College, published in Hot Working Technology in 2014, addresses a problem I have seen on countless shop floors: the premature wear and thermal fatigue cracking of H13 hot-work die steel surfaces. The author investigates the use of manual arc welding with small current and short arc to deposit a high-hardness wear-resistant layer of 4 to 6 mm thickness on the die cavity surface, then studies the effect of welding speed on the performance of the deposited layer. The key finding is that as welding speed increases, phase transformation occurs in the heat-affected zone (HAZ), and the study obtained reasonable hardfacing process parameters. When applied in production, the die life improved by 30 percent. This is not a breakthrough paper, but it is exactly the kind of practical work that pays for itself on the floor. I have signed off on many die repairs, and a 30 percent improvement in die life is a significant cost saving when you consider the downtime and the cost of new die blocks.

Interpretation of Technical Points

The author's choice of small current and short arc welding is deliberate and correct for H13 steel. H13 (4Cr5MoSiV1) is an air-hardening tool steel with a carbon content around 0.32 to 0.45 percent, chromium around 4.75 to 5.50 percent, molybdenum around 1.10 to 1.75 percent, and vanadium around 0.80 to 1.20 percent. It has excellent hot hardness and thermal fatigue resistance, but it is highly susceptible to cold cracking and HAZ softening if the welding heat input is not controlled. The use of small current and short arc minimizes the heat input, reduces dilution from the base metal, and limits the width of the HAZ. The deposited layer thickness of 4 to 6 mm is also a sensible choice. Too thin a layer will not provide sufficient wear allowance, and too thick a layer will increase the risk of cracking due to residual stress accumulation.

The critical technical parameter is welding speed. The paper reports that as welding speed increases, the HAZ undergoes phase transformation. This is a metallurgical reality that I have seen many times. At low welding speeds, the heat input is high, the cooling rate is slow, and the HAZ may experience overtempering or even re-austenitization. At high welding speeds, the heat input is low, the cooling rate is fast, and the HAZ can form untempered martensite, which is hard and brittle and prone to cracking. The optimum welding speed is the one that produces a HAZ with a tempered martensite or bainite structure that has adequate toughness and hardness. The paper does not give the exact numerical values, but the principle is clear: the welding speed must be balanced against the preheat temperature and the interpass temperature to achieve the desired HAZ microstructure.

The following table summarizes the typical process parameters for H13 hardfacing that I would recommend based on my experience and consistent with the paper's findings.

Parameter Recommended Range Remarks
Welding process SMAW, small current short arc Minimizes heat input and dilution
Electrode type Low-hydrogen basic coated, e.g., E309L or E Ni-Cr-Fe Matches the die steel composition or provides austenitic buffer layer
Electrode diameter 2.5 to 3.2 mm Smaller diameter for better control
Welding current 80 to 120 A Small current to reduce heat input
Arc voltage 20 to 24 V Short arc to minimize arc blow
Welding speed 8 to 15 cm/min Critical parameter, must be controlled to avoid HAZ phase transformation
Preheat temperature 250 to 350 °C Mandatory for H13 to prevent cold cracking
Interpass temperature 300 to 400 °C Must be controlled to avoid overtempering
Post-weld heat treatment 550 to 600 °C for 2 hours, slow cool Stress relief and tempering of the HAZ
Deposited layer thickness 4 to 6 mm Provides adequate wear allowance without excessive residual stress

Engineering Practice and Lessons Learned

I have seen many die repair jobs fail because the welder ignored the preheat requirement. H13 steel is air-hardening, and if you weld it cold, you will get a hard, brittle HAZ that will crack within hours or days of returning the die to service. The crack will propagate through the die, and you will be repairing a crack instead of a worn surface. The paper's emphasis on process parameters is well placed, but I would add that the preheat and interpass temperature control is just as important as the welding speed. In my experience, the most common cause of H13 hardfacing failure is not the welding speed but the lack of preheat or the failure to maintain interpass temperature.

Another lesson I have learned is that the electrode selection is critical. If you use a hardfacing electrode with high carbon and high chromium content, you will get a very hard deposit, but it will be brittle and prone to spalling under thermal cycling. The paper mentions a high-hardness wear-resistant layer, but I would caution against going too hard. A deposit with a hardness of 50 to 55 HRC is usually sufficient for hot work dies. If you go above 58 HRC, you will start to see chipping and cracking. The best approach is to use an austenitic stainless steel buffer layer, such as E309L, and then deposit the hardfacing alloy on top. This buffer layer absorbs the residual stress and prevents the hardfacing from cracking.

The paper reports a 30 percent improvement in die life, which is a solid result. However, I would note that die life is also influenced by the die design, the lubricant used, the forging temperature, and the maintenance schedule. A 30 percent improvement is good, but it is not a substitute for proper die maintenance and cooling. In my experience, the best results come from a combination of good hardfacing, proper die cooling, and regular inspection for thermal fatigue cracks.

Key Questions and Reflections

The paper raises an important question: what is the optimal welding speed for H13 hardfacing? The author does not provide the exact numerical value, which is a limitation. In practice, the welding speed must be determined by trial and error for each specific die geometry and welding setup. I would recommend that the welding speed be adjusted based on the appearance of the weld bead and the HAZ hardness. If the HAZ hardness is too high, the welding speed is too fast. If the HAZ hardness is too low, the welding speed is too slow. The target HAZ hardness should be in the range of 35 to 45 HRC, which indicates a tempered structure with adequate toughness.

Another question is whether the hardfacing layer should be applied in a single pass or multiple passes. For a 4 to 6 mm thick layer, multiple passes are usually required. The interpass temperature must be controlled to prevent the HAZ from being overtempered by subsequent passes. I have seen cases where the interpass temperature was not controlled, and the HAZ became soft and lost its strength, leading to premature failure of the die.

The paper does not address the issue of residual stress in the hardfacing layer. Residual stress is a major concern in die repair, because it can cause distortion of the die cavity and cracking during service. I would recommend that the hardfacing layer be stress-relieved after welding, either by a post-weld heat treatment or by peening. Peening is a practical option for large dies that cannot be heat-treated in a furnace.

Study Insights and Implications

This paper is a useful reminder that the process parameters are the key to successful hardfacing of H13 steel. The author's approach of using small current and short arc welding is sound, and the finding that welding speed affects the HAZ phase transformation is consistent with my experience. The 30 percent improvement in die life is a significant result that justifies the additional cost of hardfacing.

From a practical standpoint, I would recommend that any shop performing H13 hardfacing should have a written procedure that specifies the preheat temperature, the interpass temperature, the welding current and voltage, the welding speed, and the post-weld heat treatment. The procedure should be validated by a test coupon that is sectioned and examined metallurgically to confirm that the HAZ has the desired microstructure. The welding operator should be qualified for the procedure, and the welding parameters should be monitored and recorded for each die repair.

The paper also highlights the importance of controlling the welding speed to avoid HAZ phase transformation. In my experience, this is one of the most difficult parameters to control in manual welding, because the welder's hand speed varies. I would recommend that the welding speed be controlled by using a mechanized or semi-automatic welding process, such as a tractor-mounted welding head, for large dies. This ensures a consistent welding speed and a consistent HAZ structure.

Reference Value and Outlook

This paper has practical value for any shop that repairs H13 dies. The process parameters recommended are reasonable, and the 30 percent improvement in die life is a strong incentive to implement the process. However, the paper would be more useful if it provided the exact welding speed values and the HAZ hardness measurements. I would also like to see a comparison of different hardfacing alloys, such as cobalt-based alloys versus nickel-based alloys versus iron-based alloys, to determine which one provides the best combination of wear resistance and thermal fatigue resistance.

In the future, I would expect to see more work on the use of laser cladding or plasma transferred arc welding for H13 die repair. These processes offer better control of heat input and dilution, and they can produce a more uniform hardfacing layer with less distortion. However, they are more expensive and require specialized equipment. For many shops, manual arc welding will remain the most economical option, and the process parameters described in this paper will continue to be relevant.

In conclusion, this paper is a practical contribution to the field of die repair. It demonstrates that careful control of welding process parameters can significantly improve die life. The finding that welding speed affects the HAZ phase transformation is a valuable insight that should be incorporated into any hardfacing procedure. I would recommend this paper to any engineer who is responsible for die maintenance and repair, and I would encourage them to validate the process parameters in their own shop before applying them to production dies. The 30 percent improvement in die life is a compelling reason to invest the time and effort in process development and operator training.