WC Particle Reinforcement of High-Chromium Cast Iron Surfacing Layers: Microstructure and Wear Performance
Literature Overview and Core Findings
The paper by Gao Shasha and Ping Chaofan, published in 2020, investigates the effect of tungsten carbide (WC) particles on the microstructure and wear resistance of high-chromium cast iron (HCCI) surfacing layers produced by high-frequency induction heating. The study is particularly interesting because it uses induction heating rather than conventional arc welding, which has significant implications for the microstructure and the distribution of WC particles.
The authors found that the surfacing layer consists of gamma-Fe, (Cr,Fe)7(C,B)3, WC and W2C phases. The presence of W2C indicates that some of the WC particles partially dissolved during the induction heating process, and the dissolved tungsten and carbon reacted with the matrix to form W2C. This is a critical finding because it affects the wear mechanism. WC is extremely hard (about 2200 to 2800 HV), but W2C is even harder (about 2800 to 3200 HV). However, W2C is more brittle than WC, so the balance between hardness and toughness must be carefully controlled.
The most important result is that the optimum WC content is 30 percent by weight. At this content, the surfacing layer has the best combination of hardness and toughness, resulting in the lowest wear rate. Below 30 percent, the hardness is insufficient to resist abrasive wear. Above 30 percent, the WC particles agglomerate and the matrix cannot hold them, leading to particle pull-out and increased wear.
Microstructural Analysis and Phase Identification
Table 1: Phases Identified in the Surfacing Layer
| Phase | Hardness (HV) | Morphology | Role in Wear |
|---|---|---|---|
| gamma-Fe | 200 to 300 | Matrix, dendritic | Provides toughness, holds carbides |
| (Cr,Fe)7(C,B)3 | 1200 to 1600 | Primary carbides, hexagonal | Provides abrasion resistance |
| WC | 2200 to 2800 | Angular particles, 50 to 100 microns | Provides extreme abrasion resistance |
| W2C | 2800 to 3200 | Needle-like, at WC boundaries | Increases hardness but reduces toughness |
The gamma-Fe matrix is the continuous phase that holds the hard particles together. It is austenite that is retained at room temperature because of the high chromium and carbon content, which stabilizes the austenite. The (Cr,Fe)7(C,B)3 carbides are the primary hardening phase in high-chromium cast iron. They form during solidification and grow as large hexagonal prisms. The WC particles are added to the surfacing material as a powder, and they remain largely undissolved during the induction heating process, except at their surfaces where they react with the matrix to form W2C.
The presence of W2C at the WC-matrix interface is a double-edged sword. On one hand, it increases the hardness of the interface, which improves the abrasion resistance. On the other hand, it creates a brittle zone that can crack under impact. The authors found that at 30 percent WC content, the W2C layer is thin enough that it does not cause significant cracking, but at higher WC contents, the W2C layer becomes thicker and the particles tend to crack.
Induction Heating Process and Its Advantages
Table 2: Comparison of Induction Surfacing and Conventional Arc Surfacing
| Parameter | Induction Surfacing | Arc Surfacing (SMAW/FCAW) |
|---|---|---|
| Heat source | High-frequency induction coil | Electric arc |
| Heat input | Controlled by power and time | Controlled by current, voltage, speed |
| Dilution | 5 to 10 percent | 15 to 30 percent |
| Deposition rate | High, can be automated | Low to moderate |
| Coating thickness | 2 to 5 mm | 2 to 10 mm |
| Microstructure | Fine, uniform, no columnar grains | Coarse, columnar grains |
| WC retention | High, minimal dissolution | Low, significant dissolution |
| Equipment cost | High | Low to moderate |
| Application | Production line, large components | Field repair, small components |
The induction heating process offers several advantages for WC-reinforced surfacing. First, the heat is generated directly in the surfacing material and the substrate, rather than being transferred from an arc. This results in a more uniform temperature distribution and a finer microstructure. Second, the heating and cooling rates can be precisely controlled, which allows the WC particles to remain largely undissolved. Third, the process can be automated, which ensures consistent quality.
The main disadvantage of induction surfacing is the high equipment cost. A high-frequency induction power supply and a custom-designed coil are expensive, and the process is only economical for production runs. For field repair of bucket teeth or pipe fittings, arc surfacing is still the preferred method.
Wear Mechanism and the Effect of WC Content
Abrasive Wear Mechanism
The wear test was conducted using a rotary abrasive wear tester, which simulates the conditions in a ball mill or a chute. The abrasive particles (typically quartz or alumina) slide across the surface of the specimen, cutting and plowing the material. The wear rate depends on the hardness of the specimen relative to the hardness of the abrasive.
For the surfacing layer without WC, the wear mechanism is cutting by the abrasive particles. The (Cr,Fe)7(C,B)3 carbides provide some resistance, but the gamma-Fe matrix is relatively soft and is easily cut. The wear rate is high.
For the surfacing layer with 30 percent WC, the wear mechanism changes. The WC particles are harder than the abrasive, so they cannot be cut. Instead, the abrasive particles are blunted or broken when they hit a WC particle. The matrix is worn away around the WC particles, but the particles remain in place and continue to protect the surface. The wear rate is significantly reduced.
For the surfacing layer with 40 percent WC or more, the WC particles agglomerate and form clusters. The matrix cannot hold the clusters, and the particles are pulled out during wear. Once a particle is pulled out, it creates a cavity that traps abrasive particles, which then grind the matrix at a higher rate. The wear rate increases.
Table 3: Effect of WC Content on Hardness and Wear Rate
| WC Content (wt. percent) | Hardness (HRC) | Relative Wear Rate | Dominant Wear Mechanism |
|---|---|---|---|
| 0 | 52 | 1.00 | Cutting of matrix |
| 10 | 55 | 0.75 | Cutting of matrix, some WC protection |
| 20 | 58 | 0.55 | Mixed cutting and WC protection |
| 30 | 62 | 0.35 | WC protection, minimal pull-out |
| 40 | 60 | 0.60 | WC pull-out, cavity formation |
| 50 | 57 | 0.85 | Severe WC pull-out |
The data shows a clear optimum at 30 percent WC. At this content, the hardness is maximum (62 HRC) and the wear rate is minimum (0.35 relative). Above 30 percent, the hardness decreases because the WC particles agglomerate and create porosity, and the wear rate increases because of particle pull-out.
Engineering Practice and Lessons Learned
Application to Steel Pipe and Fitting Industry
The principles of WC-reinforced surfacing are directly applicable to the steel pipe and fitting industry, particularly for components that are subject to severe abrasive wear, such as pipe bends in slurry pipelines, valve seats, and pump casings. In slurry pipelines, the abrasive particles (sand, ore, coal) cut through the pipe wall, and the wear rate is proportional to the velocity and the hardness of the particles. A WC-reinforced surfacing layer can extend the service life by a factor of 3 to 5 compared to a conventional hardfacing layer.
Practical Considerations for Induction Surfacing
In my experience, the key to successful induction surfacing is the design of the induction coil. The coil must be designed to produce a uniform temperature distribution across the surfacing area. If the coil is too small, the edges of the surfacing area will be cold, and the WC particles will not bond to the matrix. If the coil is too large, the center will be overheated, and the WC particles will dissolve.
Another important factor is the heating and cooling rate. The heating rate should be fast enough to prevent the WC particles from dissolving, but slow enough to allow the matrix to wet the particles. In practice, a heating rate of 100 to 200 °C per second is optimal. The cooling rate should be controlled to prevent cracking. A slow cooling rate allows the austenite to transform to martensite, which is hard but brittle. A fast cooling rate retains the austenite, which is tough but soft. The optimum is a cooling rate that produces a mixture of austenite and martensite.
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| WC dissolution | Excessive heating time or temperature | Reduce heating time, lower power |
| WC agglomeration | Poor mixing of powder | Use a binder, improve mixing process |
| Porosity | Gas evolution during heating | Use degassed powder, control atmosphere |
| Cracking | High thermal stress, brittle W2C layer | Preheat substrate, control cooling rate |
| Poor bonding | Insufficient heating, low temperature | Increase power, adjust coil position |
Study Insights and Reflections
This paper is a valuable contribution to the field of wear-resistant surfacing. It provides quantitative data on the effect of WC content on the microstructure and wear resistance of HCCI surfacing layers, and it identifies the optimum WC content as 30 percent. The use of induction heating is a novel approach that offers significant advantages over conventional arc surfacing, particularly in terms of WC retention and microstructure control.
The main limitation of the paper is that it does not address the effect of WC particle size. In my experience, the particle size is as important as the content. Fine WC particles (10 to 30 microns) provide a more uniform distribution and better toughness, while coarse particles (50 to 100 microns) provide higher abrasion resistance but lower toughness. The optimum particle size depends on the specific application.
Another reflection is the importance of the matrix composition. The paper uses a high-chromium cast iron matrix, which is hard and wear-resistant but brittle. For applications that require impact resistance, a tougher matrix, such as a martensitic steel or a nickel-based alloy, may be more appropriate. The trade-off between hardness and toughness is a classic engineering decision that must be made based on the service conditions.
For the steel pipe industry, the most important takeaway is that WC-reinforced surfacing can significantly extend the service life of wear components, but it requires careful control of the process parameters and the WC content. The optimum WC content is not a fixed value; it depends on the matrix composition, the WC particle size, and the wear mechanism. A field trial is always recommended before committing to a production run.
In summary, this paper provides a solid scientific foundation for the development of WC-reinforced HCCI surfacing layers. The identification of 30 percent WC as the optimum content is a valuable finding, and the use of induction heating is a promising approach for production applications. The next step for the industry would be to develop a standard test method for evaluating the wear resistance of WC-reinforced surfacing layers, so that different products can be compared on an equal basis.
Zhuojin Pipe Fitting Co., Ltd