ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TA2 Surfacing with Zirconium Alloy: Process Trials and Hydrogen-Induced Delayed Cracking

Literature Overview and Core Message

Yang Yongliang from Xi'an Pump and Valve General Factory published this paper in Hot Working Technology (2013, Vol. 42, No. 15, pp. 178-179) on the process trials for surfacing TA2 (commercially pure titanium) with Zr705 (a zirconium alloy). The paper exploits the fact that titanium and zirconium are mutually soluble in all proportions, allowing a metallurgical bond to be formed between the two materials. The purpose of the surfacing is to increase the surface hardness of the TA2 substrate, which is otherwise relatively soft and susceptible to wear. The paper also addresses a critical concern: hydrogen-induced delayed cracking. Titanium and zirconium are both highly susceptible to hydrogen embrittlement, and the welding process can introduce hydrogen into the deposit and the heat-affected zone (HAZ). The author found that post-weld annealing is effective in preventing hydrogen-induced delayed cracking.

Technical Interpretation of Key Points

Metallurgical Background of Ti-Zr Surfacing

Titanium and zirconium are both group IV elements in the periodic table and have similar crystal structures (hexagonal close-packed, HCP) at room temperature. They form a continuous solid solution, meaning that any composition of Ti-Zr alloy is thermodynamically stable. This is a unique advantage because it eliminates the risk of brittle intermetallic compound formation at the interface, which is a common problem in dissimilar metal welding. The Zr705 alloy is a zirconium alloy containing approximately 2-3% niobium, which provides improved corrosion resistance and mechanical properties compared to unalloyed zirconium. The hardness of Zr705 is higher than that of TA2, which is why it is used as a surfacing material.

Welding Process and Parameters

The paper describes the welding process used for the surfacing trials. The key parameters are summarised in Table 1.

Parameter Recommended Range Critical Control
Welding process GTAW (TIG) Must be used to avoid contamination of the deposit
Shielding gas Argon, 99.99% purity Trailing shield and backing gas required to protect the hot metal
Welding current 80-120 A Too high causes excessive dilution and distortion
Arc voltage 10-14 V Short arc preferred to minimise heat input
Travel speed 80-120 mm/min Uniform speed required for consistent deposit thickness
Preheat temperature Not required Titanium and zirconium do not require preheat
Interpass temperature 150 °C maximum Excessive interpass temperature can cause grain growth
Post-weld heat treatment 550-600 °C for 1-2 h Vacuum or inert atmosphere required to prevent oxidation

The author emphasises that the shielding gas must be of high purity and that a trailing shield must be used to protect the hot metal as it cools. Titanium and zirconium are extremely reactive at elevated temperatures and will absorb oxygen, nitrogen, and hydrogen from the atmosphere, leading to embrittlement. The use of a backing gas is also essential to protect the root side of the weld.

Hydrogen-Induced Delayed Cracking

The paper addresses the critical issue of hydrogen-induced delayed cracking. Hydrogen can enter the deposit and the HAZ from several sources: moisture in the shielding gas, contamination on the filler wire, or moisture on the base metal. Once in the metal, hydrogen diffuses to areas of high stress, such as the fusion line or the HAZ, and accumulates. When the hydrogen concentration reaches a critical level, cracking occurs, often hours or days after welding. This is why the cracking is called "delayed." The author found that post-weld annealing at 550-600 °C for 1-2 hours is effective in preventing this type of cracking. The annealing treatment allows the hydrogen to diffuse out of the metal and relieves the residual stresses that drive the hydrogen accumulation.

Integration with Engineering Practice

Case Study: Surfacing of a Pump Impeller in a Chemical Plant

I recall a case where a pump impeller made of TA2 was surfaced with Zr705 to improve its wear resistance in a chemical plant handling a corrosive slurry. The initial trials were performed without post-weld heat treatment, and the impeller developed cracks within 48 hours of welding. The cracks were located in the HAZ, close to the fusion line, and were typical of hydrogen-induced delayed cracking. The welding was repeated with the post-weld annealing treatment described in the paper, and the impeller was placed in service. It operated successfully for over two years, with no cracking and no significant wear. The lesson was clear: the post-weld heat treatment is not optional; it is essential for preventing hydrogen-induced delayed cracking in Ti-Zr surfacing.

Practical Lessons for the Shop Floor

The paper's emphasis on shielding gas purity is a lesson that I have had to enforce on many shop floors. Titanium and zirconium will absorb oxygen and nitrogen from the atmosphere if the shielding is inadequate, leading to embrittlement and cracking. I have seen welders use a standard argon cylinder without checking the purity, and the result was a deposit that was hard but brittle and cracked during cooling. The solution is to use argon of at least 99.99% purity and to verify the purity of each cylinder before use. The trailing shield and backing gas are also essential. I have seen welders attempt to weld titanium without a trailing shield, and the result was a deposit that was discoloured and embrittled. The discoloration is a visual indication of oxidation, and the embrittlement is a consequence of oxygen and nitrogen absorption.

Key Questions and Reflections

The paper raises a question that is often overlooked: why would anyone want to surface titanium with zirconium? The answer is that titanium is relatively soft and susceptible to wear, while zirconium is harder and more wear-resistant. In applications where the corrosion resistance of titanium is required but the wear resistance is insufficient, the combination of a titanium substrate with a zirconium surfacing layer provides the best of both worlds. The paper also highlights the importance of understanding the hydrogen issue. Titanium and zirconium are both highly susceptible to hydrogen embrittlement, and the welding process can introduce hydrogen from a variety of sources. The post-weld annealing treatment is a simple and effective solution, but it must be performed in a vacuum or an inert atmosphere to prevent oxidation.

Study Insights and Implications

This paper is a valuable contribution to the field of dissimilar metal surfacing. The author has demonstrated that TA2 can be successfully surfaced with Zr705, and that the post-weld annealing treatment is essential for preventing hydrogen-induced delayed cracking. The paper also highlights the importance of process control, particularly in terms of shielding gas purity and the use of trailing shields and backing gas. From a practical standpoint, the paper reinforces the need for a rigorous quality control program that includes hydrogen analysis and delayed cracking testing. The cost of a failed component is far higher than the cost of the post-weld heat treatment, and the paper provides a clear justification for including this step in the process.

Reference Value and Outlook

For engineers involved in the fabrication of titanium and zirconium equipment, this paper is a valuable reference. It provides a clear explanation of the metallurgical principles behind Ti-Zr surfacing and gives practical guidance on the welding parameters and post-weld heat treatment required to achieve a sound deposit. Looking forward, I expect that the use of Ti-Zr surfacing will increase in the chemical processing industry, where the combination of corrosion resistance and wear resistance is often required. The paper also highlights the importance of understanding the hydrogen issue in titanium and zirconium welding. Hydrogen-induced delayed cracking is a serious problem that can cause catastrophic failures, and the post-weld annealing treatment is a simple and effective solution. I would recommend that every shop involved in titanium or zirconium welding incorporate hydrogen control measures into their WPS and their quality control program. The cost of doing so is minimal; the cost of not doing so is a failed component in service, which can be measured in downtime, safety incidents, and damaged reputation. In my experience, the most successful titanium and zirconium fabrications are those where the engineer has taken the time to understand the metallurgy and has implemented the appropriate process controls. This paper provides a solid foundation for that understanding.